READYLIFT 44-52620 2022 Toyota Tundra 6 Big Lift Instruction Manual
- June 13, 2024
- READYLIFT
Table of Contents
READYLIFT 44-52620 2022 Toyota Tundra 6 Big Lift
Product Information
- Product Name: 2022 Toyota Tundra 6 Big Lift
- Model Number: 44-52620
- Manufacturer: ReadyLIFT
- Warranty: ReadyLIFT offers a no-hassle product warranty that extends to the original purchaser of any ReadyLIFT product. If the product breaks, a new replacement part will be provided.
Product Usage Instructions
-
Before beginning the installation, thoroughly read and understand all instructions provided in this manual.
-
It is highly recommended to have the installation done by a certified professional mechanic.
-
Prior to purchasing and installing any ReadyLIFT products, it is the responsibility of the retailer, installer, and end user to review all state and local laws related
to bumper height laws and the lifting of their vehicle. -
Before moving the vehicle, drivers must check their surrounding area for obstructions, people, and animals. Raised vehicles have increased
blind spots, and failure to follow these instructions can result in damage, injury, or death. -
This kit is not compatible with aftermarket lift struts or other lift systems. The use of additional lift components can cause damage to the vehicle.
-
The kit is also not compatible with factory air suspension or advanced vehicle suspensions that may include electronic shocks, TRD Pro configurations.
-
Perform pre-installation measurements as follows:
- Vehicle Height Measurements: Measure from the center of the hub to the fender edge straight up from the hub. Measure the front and rear heights on both the driver and passenger sides.
- Record Headlamp Measurements: Measure the height of the headlamps before and after installation on both the driver and passenger sides.
-
Refer to the Bill of Materials section for a list of components and hardware included in the kit.
-
Follow the provided step-by-step instructions for installation, ensuring proper torque specifications and sequence for all bolts and nuts.
-
If any issues arise during the installation or if there are warranty concerns, contact ReadyLIFT at 877-759-9991 or email support@readylift-ami.com. Additional support can be found on the ReadyLIFT website at www.readylift.com. Note: It is important to retain this document in your vehicle at all times for reference.
44-52620 2022 Toyota Tundra 6″ Big Lift
IF your ReadyLIFT® product has a damaged or missing part, please contact
customer service directly and
a new replacement part will be sent to you immediately. For warranty issues,
please return to the place of installation and contact ReadyLIFT.
877-759-9991
MON-FRI 7AM-4PM PST OR
EMAIL: support@readylift-ami.COM WEBSITE: ReadyLIFT.COM
Please retain this document in your vehicle at all times.
READYLIFT ” NO HASSLE” PRODUCT WARRANTY
This unique “no hassle” product warranty proves out commitment to the quality
of every product the ReadyLIFT produces. ReadyLIFT product warranty only
extends to the Original Purchaser of any ReadyLIFT product. If it breaks, we
will give you a new part.
READYLIFT “NO HASSLE” WARRANTY PROCEDURES Any ReadyLIFT products containing
missing or defective components will be covered under warranty by ReadyLIFT.
Please call 800-549-4620 to initiate a
warranty claim. Rest assured out customer service team will urgently address
the matter and expedite the replacement parts. In the event of a defective
product, ReadyLIFT may request a return of the defective product (at
ReadyLIFT’s expense) so the quality team can analyze the nature of the defect.
Returning defective product will not delay the replacement part delivery.
ReadyLIFT leveling kit, block kits, and lift kit products are NOT intended for
off-road abuse. Any abuse or damage as a result of off-road use voids the
warranty of the ReadyLIFT product. Exception: ReadyLIFT Jeep SST and Terrain
Flex Lift Kits are designed for normal off-road use to compliment the Jeep
vehicle’s off-road capability. All Jeep Lift Kit products are covered under
warranty when used in recreational offroad environments. Warranty does not
apply to discontinued, clearance or outlet products. Wearable components
including but not limited to, shocks, ball joints, heim joints, bushings, and
steering extensions, are covered for up to 1-year. Labor, installation,
surcharges or any other applicable fees from the original purchase are
nonrefundable. ReadyLIFT is not responsible for any consequential damage to
the vehicles. ReadyLIFT reserves the right to change, modify, or cancel this
warranty without prior notice.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
READ INSTRUCTIONS THOROUGHLY AND COMPLETELY BEFORE BEGINNING INSTALLATION.
INSTALLATION BY A CERTIFIED PROFESSIONAL MECHANIC IS HIGHLY RECOMMENDED.
READYLIFT® IS NOT RESPONSIBLE FOR ANY DAMAGE OR FAILURE RESULTING FROM
IMPROPER INSTALLATION. Safety Warning
MISUSE OF THIS PRODUCT COULD LEAD TO INJURY OR DEATH. Suspension systems or
components that enhance the on and off-road performance of your vehicle may
cause it to handle differently than it did from the factory. Extreme care must
be used to prevent loss of control or vehicle rollover during abrupt
maneuvers. Always operate your vehicle at reduced speeds to ensure your
ability to control your vehicle under all driving conditions. Failure to drive
safely may result in serious injury or death to driver and passengers. Driver
and passengers must ALWAYS wear your seat belts, avoid quick sharp turns and
other sudden maneuvers. ReadyLIFT Suspension does not recommend the combined
use of suspension lifts, body lifts, or other lifting devices. You should
never operate your vehicle under the influence of alcohol or drugs. Constant
maintenance is required to keep your vehicle safe. Thoroughly inspect your
vehicle before and after every off-road use.
It is the responsibility of the retailer and/or the installer to review all
state and local laws, with the end user of this product, related to bumper
height laws and the lifting of their vehicle before the purchase and
installation of any ReadyLIFT products.
It is the responsibility of the driver/s to check their surrounding area for
obstructions, people, and animals before moving the vehicle. All raised
vehicles have increased blind spots; damage, injury and/or death can occur if
these instructions are not followed.
.
Installation Warning All steps and procedures described in these instructions
were performed while the vehicle was properly supported on a two post vehicle
lift with safety jacks. Use caution during all disassembly and assembly steps
to insure suspension components are not over extended causing damage to any
vehicle components and parts included in this kit. Included instructions are
guidelines only for recommended procedures and are not meant to be definitive.
Installer is responsible to insure a safe and controllable vehicle after
performing modifications. ReadyLIFT Suspension recommends the use of an OE
Service Manual for model/year of vehicle when disassembly and assembly of
factory and related components. Unless otherwise specified, tighten all bolts
and fasteners to standard torque specifications listed within the OE Service
Manual. Suspension components that use rubber or urethane bushings should be
tightened with the vehicle at normal ride height. This will prevent premature
wear or failure of the bushing and maintain ride comfort. Larger tire and
wheel combinations may increase leverage on suspension, steering, and related
components. Due to payload options and initial ride height variances, the
amount of lift is a base figure. Final ride height dimensions may vary in
accordance to original vehicle ride height. Always measure the vehicle ride
height prior to beginning installation.
SAEJ2492 Warning
By installing this product, you acknowledge that the suspension of this
vehicle has been modified. As a result, this vehicle may handle differently
than that of factory-equipped vehicles. As with any vehicle, extreme care must
be used to prevent loss of control or roll-over during sharp turns or abrupt
maneuvers. Always wear seat belts, and drive safely, recognizing that reduced
speeds and specialized driving techniques may be required. Failure to drive
this vehicle safely may result in serious injury or death. Do not drive this
vehicle unless you are familiar with its unique handling characteristics and
are confident of your ability to maintain control under all driving
conditions. Some modifications (and combinations of modifications) are not
recommended and may not be permitted in your state. Consult your owner’s
manual, the instructions accompanying this product, and state laws before
undertaking these modifications. You are responsible for the legality and
safety of the vehicle you modify using these components.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
2
Due to payload options and initial ride height variances, the amount of lift
is a base figure. Final ride height dimensions may vary in accordance to
original vehicle ride height. Always measure the vehicle ride height prior to
beginning installation. A lifted vehicle may have different headlight aim
performance. ReadyLIFT recommends marking and recording the headlight beam
position before kit installation and then adjusting, if necessary, the
headlamps to the same height settings after kit installation. Set the vehicle
on a level surface 10′ to 15′ from a solid wall or garage door. (This is a
general distance with some manufacturers requiring different distances.) Note
the top height of the low beam’s bright spot, the top of the most intense part
of the beam, for driver and passenger side. Height may vary from side to side.
Repeat this procedure and adjust after lift kit is installed. Adjust if the
aim is off by turning the adjusters gradually (a quarter of a turn) and
looking to see where the new alignment falls. It may be easier to block one
headlamp while adjusting the other. Consult the owner operation manual for
procedures to adjust headlights – many automakers offer headlight aiming
specs. Some states have their own specifications when it comes to headlight
aim, so it’s best to follow those rules when alighting headlights.
This suspension system was developed using a 37 x 12.5 tire with 20×9 wheel
and a offset of 18mm. If wider tires are used, offset wheels may be necessary
and trimming may be required. Factory wheels can be used but are not
recommended with tires over 10.5″ wide. The stock spare rim can be run in an
emergency – exercise extreme caution under stock spare tire operating
conditions. Please note that, if running the spare factory tire, it is done
for short distances and a speed not to exceed 45mph or damage to differentials
may occur.
IMPORTANT NOTE:
Kit not compatible with aftermarket lift struts or other lift systems. Use of
additional lift components will damage vehicle. Kit is not compatible with
factory air suspension or advanced vehicle suspensions which may include
electronic shocks TRD Pro configurations.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
3
PRE-INSTALLATION MEASUREMENTS:
It is imperative that you record the following measurements and factory components in the tables below. ReadyLIFT tests and records as much data from each application as available at the time of product development. Vehicle manufacturers may change components or add models with different options. Recording and not exceeding the fender-to-hub-center ReadyLIFT calls out will ensure the lift on the vehicle is correct. These measurements will affect the performance of this lift kit. Failure to ensure proper stock conditions may result in over lifting, causing premature failure of axles, CV boots and drivetrain. Over lifting a vehicle will also result in an incorrect wheel alignment. This will wear tires incorrectly. Incorrect alignment will cause poor vehicle handling issues including but not limited to under steer. Over lifting will also cause a shock top off condition resulting in poor ride quality accompanied by pops and clunks which are symptoms of prematurely wearing components. Failure to adjust head lamps may cause dangerous driving conditions for you and other drivers on the road. Record the head lamp position before the installation of this lift or leveling kit and adjust to original factory position after the completion to ensure a safe and enjoyable experience.
VEHICLE HEIGHT MEASUREMENTS
Front Rear
Driver Before
Driver After
Passenger Before
Passenger After
MEASUREMENT IS TO BE PERFORMED FROM CENTER OF HUB TO FENDER EDGE STRAIGHT UP FROM HUB.
Driver Before
RECORD HEAD LAMP MEASUREMENTS
Driver After
Passenger Before
Passenger After
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
4
BILL OF MATERIALS
COMPONENTS
HARDWARE
Front Crossmember
1 M18-2.5 X 140mm Hex Head Bolt
2
Rear Crossmember Front Strut Spacer Skid Plate Front Sway Bar Drop–Left
Front Sway Bar Drop–Right
Front Brake Line Bracket–Right 1 Front Brake Line Bracket–Right 2
1 M18-2.5 Top Lock Nut
4
2 1 1
M18 Flat Washer M18-2.5 X 160mm Hex Head Bolt
8 2
1 3/8-16 X 1in Hex Head Bolt
7
1 3/8-16 Top Lock Nut
4
1 3/8 Flat Washer
14
Front Brake Line Bracket–Left 1
1 7/16-20 Serrated Flange Nut
8
Front Brake Line Bracket–Left 2
1 M10-1.25 X 25mm Flange Bolt
6
Cam Block Off Plates
8 M10-1.25 Flange Nut
8
Headlight Sensor Bracket Sleeve and HSB Lft 1 M8-1.25 X 40mm Flange Bolt
2
Knuckle–Left Hand Side Knuckle–Right Hand Side
Front Bump Stop–Left Hand Side
Front Bump Stop–Right Hand Side Rear Crossmember Nut Plate 1/4″ Front Diff
Vent Hose
1 M8-1.25 X 25mm Hex Head Bolt
12
1
1 1 1
M8-1.25 Top Lock Nut M8 Flat Washer M12-1.75 X 50 Fully Threaded
12 24 4
1 M12-1.75 X 35mm Hex Head Bolt
1
Rear Trackbar Bracket
1 M12-1.75 Top Lock Nut
5
Rear Sway Bar Drop–Left
1 M12 Flat Washer
10
Rear Sway Bar Drop–Right
1 M14-2.00 X 90mm Hex Head Bolt
1
6″ Rear Coil Spring
2 M14-2.00 Top Lock Nut
1
Rear Bump Stop–Left
1 M14 Flat washer
2
Rear Bump Stop–Right Rear Bump Stop Extension Rear ABS Relocator
1 2 2
5/32 X 2in Cotter Pin 1/8 X 1.5in Cotter Pin
4 4
Rear ABS Bracket
2
Rear Shock
2
Before starting installation: ReadyLIFT Suspension highly recommends that the
installation of this product be performed by a professional mechanic with
experience working on and installing suspension products. Professional
knowledge and skill will typically yield the best installation results. If you
need an installer in your area, please contact ReadyLIFT Suspension Customer
Service to find one of our “ProGrade” Dealers.
INSTALLATION BY A PROFESSIONAL IS HIGHLY RECOMMENDED.
· A Factory Service Manual for your specific Year / Make / Model is highly
recommended for reference during installation.
· All lifted vehicles may require additional driveline modifications and / or
balancing. · A vehicle alignment is REQUIRED after installation of this
product. · Speedometer / Computer recalibration is required if changing +/-
10% from factory tire diameter. · A vehicle lift or hoist greatly reduces
installation time. Installation time estimates are based on an avail-
able vehicle hoist. · Vehicle must be in excellent operating condition. Repair
or replace any and all worn or damaged com-
ponents prior to installation.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
5
Parts shown in red for picture clarification only
ReadyLIFT recommends all steps and procedures described in these instructions
be performed while the vehicle is properly supported on a two post vehicle
lift with safety jacks. Otherwise, park vehicle on a clean flat surface and
block the rear wheels for safety. Engage the parking brake. Disconnect the
vehicle power source at the ground terminal on the battery. Lock the steering
wheel in the straight forward position with the column lock or steering wheel
locking device. Raise the front of the vehicle and support with safety jack
stands at each frame rail behind the lower control arms. Remove the front
wheels. Starting with the front of the vehicle, all steps are to be completed
on both sides of the vehicle unless instructed.
Remove the two (2)(one on each side) screws retaining the factory air dam to
the chassis. Retain factory hardware.
Remove the two (2) screws retaining the factory air dam to the actuator.
Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
6
Remove the four (4) bolts for the front dust shield. Retain factory hardware.
Remove the sway bar end link bolt from the lower control arm and slide the end
link off of its perch. Retain factory hardware.
Remove the four (4)(two on each side) sway bar bolts and remove the sway bar
from the vehicle. Retain factory hardware.
Remove the ABS wire bracket on the upper control arm and strut perch. Retain
factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
7
Remove the brake line from the bracket on the chassis. Do not disconnect brake
line hydraulic connections. Retain factory hardware.
Remove both screws retaining the ABS wire to the middle of the knuckle. Retain
factory hardware.
Remove the ABS wire bracket at the bottom of the knuckle. Retain factory hardware.
Using a trim removal tool, remove the four (4) clips for the plastic dirt shield. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
8
Remove the rear cover for caliper hanger hole. Retain factory hardware.
Support the lower control arm with a suitable jack. Loosen but DO NOT remove
the lower strut bolt.
Loosen but DO NOT remove the four (4) upper strut bolts.
Loosen but DO NOT remove inner control arm nuts.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
9
Remove the two (2) caliper bolts. Hang the caliper out of the way. Remove
rotor. Retain factory hardware.
Remove the upper ball joint retaining clip by pushing in on the clip nub.
Release the hook from the castle nut and remove the clip.
Loosen but DO NOT remove the upper ball joint nut.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
10
Remove the cotter pin and castle nut from the tie rod. Use the appropriate
tool to release the tapper. Retain factory hardware.
Remove the CV axle dust shield. Retain factory hardware.
Remove the cotter pin, sleeve, and nut. Release the axle from the hub. Retain
factory hardware.
Remove the two (2) lower ball joint bolts. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
11
Use the appropriate tool to release the taper on the upper ball joint. Remove
the upper ball joint nut. Remove the knuckle from the vehicle. Retain factory
hardware.
Support the CV axle to prevent damage
Remove the lower shock bolt, let the lower control arm hang out of the way.
Remove the shock from the vehicle. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
12
Remove the four (4) nuts holding the drive shaft to the front differential. Support the drive shaft and remove it from the front differential. Retain factory hardware.
Support the front differential with a jack. Remove the three bolts holding the
passenger side bracket to the differential. Remove the nut and bolt holding
the bracket to the chassis and remove the bracket from the vehicle. Retain
factory hardware.
Remove the two bolts holding the driver side bracket to the differential.
Remove the nut and bolt holding the bracket to the chassis and remove the
bracket from the vehicle. Retain factory hardware.
Unplug the front differential control plug from the vehicle. Remove the bolt
holding the plug wire to the steering rack. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
13
From the driver side wheel well, disconnect the front differential vent hose from the differential.
Remove the differential from the vehicle. Retain factory hardware.
On the backside of the rear crossmember, mark a vertical line 2.5 inches from
the center of the left hand side alignment cam hole. Also, mark a vertical
line 10.75 inches from the same alignment cam hole.
Using a suitable cutting tool, cut the crossmember at the marked lines. Debur
any sharp edges. Coat the cut edges with a suitable protectant.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
14
Temporally install the rear crossmember with the differential mount on the
driver side. Use the supplied M18-2.5 X 160mm hex heads bolts and cam block
off plates (four total). Mark the three (3) crossmember mounting holes. Remove
the crossmember and drill marked holes to 25/64″. Coat with a suitable
protectant.
Remove the factory front differential vent hose. Retain factory hardware.
Using the factory hose clips, attach the supplied vent hose to the chassis
side factory mounting location.
Install the front crossmember using the supplied M18-2.5 X 140mm hex head
bolts, M18-2.5 lock nuts, M18 flat washers (4), and cam block off plates (4).
Install the bolts from front to rear It’s imperative that the notches on all
four cam plates are all facing the same direction. Ex., all are pointed up.
Raise the front differential and install the to the front crossmember using
the factory front differential mounting brackets and hardware. DO NOT TIGHTEN
AT THIS TIME.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
15
Install the rear crossmember using he supplied M18-2.5 X 160mm hex head bolts,
M18-2.5 locking nuts, and M18 flat washers, Slide the rear crossmember nut
plate into the factory rear crossmember.
Use the supplied 3/8-16 X 1in hex head bolts and 3/8-16 flat washers to secure
the rear crossmember to the chassis. DO NOT TIGHTEN AT THIS TIME.
Use factory hardware to attach the rear front differential mount to the rear
crossmember. DO NOT TIGHTEN AT THIS TIME.
Use factory hardware to attach the driveshaft to the front differential.
Torque factory hardware to 60 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
16
Remove the bolt holding the front differential control plug to the front
differential (left image). Plug the harness into the factory plug location.
Attach the harness to the steering rack using factory hardware (right image).
Torque to 8 ft-lbs.
Attach the supplied differential vent hose to the front differential using the
factory hose clip.
Use factory hardware to install the factory lower control arms. Install the
bolts with the bolt heads facing towards each other. DO NOT TIGHTEN AT THIS
TIME.
Remove the factory bump stop from the chassis mount. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
17
Using the supplied M10-1.25 X 25mm hex head flange bolts (3) and M10-1.25
flange nuts (3), attach the front bump stops to the rear crossmember. Note:
the long flange goes towards the rear of the vehicle. DO NOT TIGHTEN AT THIS
TIME.
Use a supplied M10-1.25 X 25 hex head flange bolt to attach the bump stop to
the chassis. Install from the bottom up.
Feed a ratchet extension up through the lower mounting hole to tighten the
bolt. Torque hardware to 40 ft-lbs.
Torque the chassis to differential drop bracket hardware to 110 ft-lbs. Torque the driver side bracket to differential hardware to 110 ft-lbs. Torque the passenger side bracket to differential hardware to 145 ft lbs. Torque the crossmember to chassis M18 hardware to 250 ft-lbs. Torque the crossmember to chassis 3/8-16 hardware to 40 ft-lbs. Torque the bump stop to crossmember hardware to 40 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
18
Insert a supplied M10-1.25 flange nut into the bump stop. Screw the factory
bump stop into the nut. Torque to 40 ft-lbs.
Attach the front strut spacer to the factory strut using factory hardware.
Torque to 40 ft-lbs.
Install the strut and spacer assembly into the vehicle using the supplied 7/16-20 serrated flange nuts. DO NOT TIGHTEN AT THIS TIME.
Raise the lower control arm enough to insert the factory lower strut bolt and nut. Install from front to rear. DO NOT TIGHTEN AT THIS TIME.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
19
Remove the four (4) factory bolts holding the knuckle to the hub. Retain factory hardware.
Carefully remove the dust seal off of the back of the knuckle. Using a flathead screwdriver or similar tool, carefully work around the outer edge of the seal to release it from the knuckle. Retain factory hardware.
Using factory hardware, attach the factory hub to the supplied knuckle. Torque
to 60 ft-lbs. Transfer the factory dust seal to the supplied knuckle. Use a
blunt punch to set the seal into the knuckle. NOTE: ONLY PRESS ON THE
HORIZONTAL FACE.
Install the knuckle into the corner package. Insert the CV axle into the hub
and thread the factory axle nut on. DO NOT TIGHTEN AT THIS TIME. Support the
knuckle from falling through the next step.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
20
Using factory hardware, insert the upper control arm ball joint into the knuckle. Rest the knuckle on the knuckle adaptor/ steering stop. DO NOT TIGHTEN AT THIS TIME.
Apply a small amount of medium duty thread locker to the factory lower ball
joint bolts.
Torque the lower ball joint bolts to 115 ft -lbs. Torque the upper ball joint
hardware to 70 ft-lbs. Reattach the factory hook into the castle nut.
Torque the axle nut to 250 ft-lbs. Slide the factory axle nut cover on. Use a
supplied 5/32 X 2in cotter pin to secure the axle nut.
Remove the factory tie rod from the tie rod shaft and switch with the opposite side (driver to passenger, passenger to driver). Final torque of tie rod jam nut to be set by alignment tech. Note: It may help to temporally install the tie rod into the knuckle to loosen the tie rod jam nut. Also, note the orientation of the nub on the tie rod.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
21
Note how the nub on the tie rod is opposite of the factory location in the previous step.
Using factory hardware, attach the tie rod to the knuckle from the top. Torque
to 160 ft-lbs. Use a supplied 1/8 X 1.5in cotter pin to secure the factory
castle nut.
Remove the two (2) nuts holding the brake line bracket to the body (driver
shown in the left image, passenger shown in the right image).
Remove the driver side brake lines from the plastic clip on the inside of the body panel opposite of the bracket removed in the previous step (left image). Use a trim removal tool to remove the clip holding the three brake lines from the body panel opposite of the bracket removed in the previous step (right image).
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
22
Attach the supplied front brake line bracket 2 (left and right) to the body
using factory hardware. Attach the factory brake line bracket to the supplied
bracket using the supplied M8-1.25 X hex head bolt, M8-1.25 locking nut, and
four (4) M8 flat washers. Torque all hardware to 20 ft-lbs.
Slide the rotor onto the hub. Use a lug nut to keep it in place. Using a small
amount of medium strength thread locker, attach the caliper to the knuckle
using the factory hardware. Torque factory hardware to 110 ft-lbs.
Remove the factory brake line bracket from the chassis. Retain factory
hardware. Using factory hardware, install the supplied brake line bracket.
Note that they are left and right side specific. Torque to 20 ft-lbs. Attach
the brake line to the supplied brake line bracket using factory hardware and
the supplied M8-1.25 locking nut and M8 washer. Torque to 20 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
23
Attach the ABS wire to the strut perch using factory hardware. Torque to 20 ft-lbs.
Using factory hardware, attach the ABS sensor wire at the middle of the knuckle. Torque to 20 ft-lbs.
Using factory hardware, attach the ABS sensor wire at the bottom of the knuckle. Torque to 20 ft-lbs.
Using factory hardware, attach the ABS/ wheel speed sensor. Torque to 8 ft- lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
24
On the factory dirt shields removed on page 8, remove the retaining clip for
the sound deadening in the front lower corner. Mark and trim a semi-circle
1.75″ from the edges (left image). Drill a hole 0.75″ from cut edge with a J
sized drill. Insert previously removed clip (right image).
Replace the factory dirt shields onto the vehicle.
Using factory hardware, install the front sway bar drop brackets. Note that they are handed with the pockets facing inboard and the smaller mating faces towards the front of the vehicle. DO NOT TIGHTEN AT THIS TIME.
FRONT
Using factory hardware, attach the sway bar end links to the lower control arms. DO NOT TIGHTEN AT THIS TIME.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
25
Using the supplied M12-1.75 X 50 bolt, locking nuts, and flat washers, attach
the sway bar to the sway bar brackets. Torque the sway bar factory hardware to
80 ft-lbs. Torque the sway bar bracket supplied hardware to 60 ft-lbs. Install
the supplied skid plate using the supplied 3/8-16 X 1″ hex head bolts, lock
nuts, and flat washers. Torque to 40 ft-lbs.
Using factory hardware, install the factory front dust shield. Torque to 20
ft-lbs.
Trim the front air dam 0.25″ from the inner edge. Contour the line to blend it
into the air dam.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
26
Using factory hardware, install the factory air dam onto the actuator. DO NOT TIGHTEN AT THIS TIME.
Using factory hardware, attach the front air dam to the chassis. Torque factory hardware to 20 ft-lbs.
Install the front wheels and lower vehicle to the ground. Torque the lug nuts to the wheel manufacturer specs. Torque the lower strut factory hardware (2x) to 115 ft-lbs. Attach the vehicle negative power source.
Torque the sway bar end link factory hardware to 80 ft-lbs. Have the alignment
set to the recommended specs at the end of the instructions.
Rear instructions continued on following page.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
27
Rear Installation Block the front tires and raise the rear of the vehicle
using a suitable jack. Support with jack stands at each frame rail in front of
the rear bumper. Remove the rear wheels. It can help to remove the spare tire.
Steps must be repeated on both sides concurrently.
Remove the five (5) bolts holding the rear brake line to the axle. Retain
factory hardware.
Remove the bolt (one on each side) holding the brake line to the axle. Retain factory hardware.
Remove the bolt (one on each side) holding the brake line to the body. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
28
Remove the bolt holding the brake line to the frame. Retain factory hardware.
Remove the bolt holding the brake line to the axle. Retain factory hardware.
Remove the end link nut and let the end hang out of the way. Retain factory hardware.
Remove the Panhard bar bolt at the axle and let it rest in the mounting perch. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
29
Loosen but DO NOT remove the DRIVER upper control nut at the axle. Remove the
PASSENGER upper control bolt at the axle. Retain factory hardware.
Loosen but DO NOT remove the lower control nut at the axle.
Loosen but DO NOT remove the lower shock bolt.
Remove the upper shock nut and bushing. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
30
Lower the axle enough to remove the rear springs. Retain factory hardware.
Remove the factory bump stop from the factory spring isolator.
Install the supplied rear bump stop extension onto the factory isolator.
Attach the supplied bump stop extension to the factory isolator using thread locker and the supplied M10-1.5 X 25mm hex bolt and M10 washer. Torque the M10 hardware to 20 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
31
Insert the factory bump stop into the extension.
Place the factory bump stop and isolator on the top of the spring as shown.
Insert the spring onto the axle. Raise the axle and make sure the spring is
properly seated on the axle and in the frame.
Install the PASSENGER upper control using factory hardware. DO NOT tighten at
this time.
Remove the factory end link mount. Retain factory hardware.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
32
Remove the three bolts holding the factory bump stop to the frame. Retain
factory hardware.
Using factory hardware, install the supplied end link bracket to the frame.
Torque to 60 ft-lbs.
Place the supplied Panhard bar bracket in the factory location as shown.
Using factory hardware, attach the bracket to the axle in the factory mounting location. DO NOT TIGHTEN AT THIS TIME.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
33
Using the supplied M12-1.75 X 35mm hex head bolt, M12-1.75 locking nut, and
two (2) M12 washers attach the Panhard bar bracket to the factory upper
control arm bracket. Install front to back. DO NOT TIGHTEN AT THIS TIME.
Using the supplied M14-2.00 X 90mm hex head bolt, M14-2.00 locking nut, and
two (2) M14 washers attach the factory Panhard bar to the track bar bracket.
Install front to back. DO NOT TIGHTEN AT THIS TIME.
Attach the supplied bump stop extension to the frame with factory hardware in
the bottom holes. Torque all hardware to 20 ft-lbs.
Attach the factory bump stop to the extension using the supplied M8-1.25 X 20mm hex head bolts and M8 flat washers, starting with the lower bolts. Torque hardware to 20 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
34
Attach the supplied rear shock to the lower mount using factory hardware. DO NOT TIGHTEN AT THIS TIME.
Using the supplied shock hardware, attach the shock to the upper mount. Torque the upper shock nut to 60 ft-lbs. Torque the lower shock bolt to 60 ft-lbs.
Install the rear ABS bracket between the brake line and the axle using the factory bolt (one on each side) holding the brake line to the axle. Torque to 20 ft-lbs.
Using the supplied M8-1.25 X 20mm hex head bolt, M8-1.25 locking nut, and two (2) M8 washers attach the brake line to the supplied bracket. Torque to 20 ft- lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
35
Install the rear ABS relocator between the brake lines and the axle using the
factory bolt holding the brake line to the axle. Using the supplied M8-1.25 X
20mm hex head bolt and M8 washer, attach the brake line to the supplied
bracket. Torque to 20 ft-lbs.
Install the rear ABS relocator between the brake lines and the frame using the
factory bolt holding the brake line to the frame. Using the supplied M8-1.25 X
20mm hex head bolt, M8-1.25 locking nut, and two (2) M8 washers attach the
brake line to the supplied bracket. Torque to 20 ft-lbs.
Install the end link onto the supplied bracket using factory hardware. Torque
to 60 ft-lbs.
Install the rear wheels and lower vehicle to the ground. Torque the lug nuts to the wheel manufacturer specs. Torque the lower control arm factory hardware (2x) to 100 ft-lbs. Torque the upper control arm factory hardware (2x) to 100 ft-lbs. Torque the Panhard arm factory hardware (2x) to 100 ft-lbs. Torque the M14 Panhard bar bracket hardware to 110 ft-lbs. Torque the M12 Panhard bar bracket hardware to 60 ft-lbs.
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
36
FAILURE TO PERFORM THE POST INSPECTION CHECKS MAY RESULT IN VEHICLE COMPONENT
DAMAGE AND/OR PERSONAL INJURY OR DEATH TO THE DRIVER AND/OR OTHERS.
Final Checks & Adjustments Once the vehicle is lowered to the ground, check
all parts which have rubber or urethane components to ensure proper torque.
Torque lug nuts to the wheel manufacturer specs. Move vehicle backwards and
forwards a short distance to allow suspension components to adjust. Turn the
front wheels completely left then right and verify adequate tire, wheel, brake
line, and ABS wire clearance. Test and inspect steering, brake and suspension
components for tightness and proper operation. Inspect brakes hoses and ABS
lines for adequate slack at full extension, adjust as necessary. RECHECK ALL
HARDWARE FOR PROPER TORQUE VALUES AFTER 500 MILES, AND THEN PERIODICALLY AT
EACH SERVICE INTERVAL THERAFTER.
Vehicle Handling Warning Increasing the height of your vehicle raises the
center of gravity and can affect stability and control. Use caution on turns
and when making steering corrections. Vehicles with larger tires and wheels
will handle differently than stock vehicles. Take time to familiarize yourself
with the handling of your vehicle.
Wheel Alignment/Headlamp Adjustment It is necessary to have a proper and
professional wheel alignment performed by a certified alignment technician.
Align the vehicle to factory specifications. It is recommended that your
vehicle alignment be checked after any off-road driving. In addition to your
vehicle alignment, for your safety and others, it is necessary to check and
adjust your vehicle headlamps for proper aim and alignment. If the vehicle is
equipped with active or passive safety/collision monitoring and/or avoidance
systems including, but not limited to, camera- or radar-based systems, check
and adjust your vehicle’s systems for proper aim and function.
Front Camber Caster Toe
RECOMMENDED ALIGNMENT SPECS
Driver +0.2 +3.1 +0.12
Passenger +0.2 +3.1 +0.12
Tolerance +/- 0.5 +/- 0.5 +/- 0.05
Total / Split +0.0 +0.0 +0.24
44-52620-IM-AA
www.ReadyLIFT.com – Phone: 877-759-9991
37
References
- Foundational Technology - AMI
- ReadyLIFT | Leveling Kits | Lift Kits | Jeep Lift Kits | Block Kits | ReadyLIFT Suspension
- ReadyLIFT | Leveling Kits | Lift Kits | Jeep Lift Kits | Block Kits | ReadyLIFT Suspension
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>