Goodflys Technology GF-H1PRO Smart Helmet User Guide

Goodflys Technology GF-H1PRO Smart Helmet

Product Information

Specifications:

• FCC ID: ABGF-HPRO
• Compliance: Part of FCC Rules

Product Usage Instructions

FCC Caution:
This device complies with part of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Compliance Guidelines:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FAQ

• Q: What should I do if the device causes interference?
  A: If the device causes interference, try repositioning it or contacting customer support for assistance.

• Q: Can I modify the device?
  A: Any modifications to the device must be approved by the responsible party to maintain compliance with FCC regulations.

Introduction

Note: This diagram is for reference only. If the actual product appears different from the diagram, the real prod cut shall prevail.

Packing List

• Helmetx 1
• Quick Start Guide x 1
• Remote Controller x 1
• Type-C USB Charging Cable x 1

Wearing Instructions

Operating instructions

Instructions of Buttons
Note: This button got 8 functions, please read below instructions carefully before use.

1. ****Hold press this button for 3-5 seconds, turn on the helmet. You will hear a voice saying “Ready for Connection’ and LED Taillight will flash, meaning the boot 1s successful.

2. ****Hold press this button for 3-5 seconds, turn off the helmet. You will hear a voice saying “Goodbye”, meaning the shutdown is successful.

3. ****Single press this button to play/pause music and answer/end incoming calls.

4. ****Quickly press twice this button, Central Taillight flashing mode.

5. ****Quickly press twice this button again, change to L &R Taillight Double-Flash mode.

6. ****Quickly press twice this button again, change to Central Taillight and Lateral Taillights alternate flashing mode.

7. ****Quickly press twice this button again, turn off the Taillights.

8. ****Quick press this button 5 times to reset.

9. ****Single press this button, turn on the headlight, 1000/oLm.

10. ****Press again, turn off the headlight.

11. ****Press again, change the Lm or flash mode.

Charging
Open the soft rubber lid with “Type-C”, USB charging cable will be seen. Insert a USB cable into it. Charging starts when red light indicator appeared and charging completed when red light indicator disappeared(charge no less than 3hrs.).

Connect to the Remote Controller
Hold press this button on remote controller, the green light will be on, meaning it is turned on. And then quickly press this button 5 times to reset the remote controller and it will be connected with Helmet Automatically and will hear a voice saying “Remote connected” from the helmet after connected successfully.

Tips:

1. To ensure the connection sigal stability, please try not to place your mobile phone right againt your body.
2. To connect remote controller to helmet first and then connect helmet to your smartphone via bluetooth, click the player button on remote control to activate the smartphone’s voice assistant service.

Connect to Helmet Bluetooth Player
( Tip: Once connected, it can control the music player as well as make or receive a call. To ensure the stability of the connection, please try to postion your smartphone in front of you).
When helmet is powered on, you will hear a voice saying “ready for connection”. Remote controller will connect to the helmet automatically once powered on. And will hear a voice saying” remote connected” after connected successfully. Open your smartphone’s bluetooth, find lizvie helmet and pair it. Will hear a voice saying “bluetooth connected” after connected successfully.

Functions

Instructions for Use and Care

1. Please choose the size that feels secure, and comfortable and fits well on the head.
2. Please adjust the strap’s position to be firm and comfortable.
3. A helmet cannot always protect against injury but can decrease the risk of it only.
4. Please discard the destroy the helmet if subjected to a severe impact.
5. Clean only with mild soap and water, solvents may damage the helmet. Take good care of it, don’t strike the helmet.
6. Please don’t modify or remove any of the original parts of the helmet.
7. Normally, valid for 3 years without impact.

Attention

1. The helmet contains electronic parts inside. Please do not take a long ride in the rain although the helmet can prevent the rain from splashing.
2. After the helmet gets wet in the rain, the water droplet might occur in the chimney of LED Taillights. The water drop. lets will disappear when you put the helmet under the ventilation environment for 1-2 days.
3. The helmet contains the battery. The battery capacity varies with temperature change. The battery life can decay when the helmet is used at low temperatures or below Zero degrees Celsius.
4. For the battery lifetime, please charge the helmet completed every time.

Technical Specifications

• Charging port: Type-C USB
• Electricity parameter: DC SV/lA
• Charging time: 3-4hrs
• Waterproof class: I PXS
• Battery Working Time: Max 60hrs (varies depending on)
• Storage Temperature: -l0°C~45°C
• Usage Temperature: 0°C~45°C

Electronic Functions Troubleshooting
During the usage, if any troubles occur, please press 5 times (power button) or long press 10 seconds to reset the device If the problems still can not be solved, please contact the after-sales service centre.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>