Shenzhen Goodflys Technology GF-H300 Smart Clock Camera(Wireless Charger) Installation Guide

June 6, 2024
Shenzhen Goodflys Technology

Quick Installation Guide
Smart Fast Wireless Charger

REV1.0.0

product Diagram

Description Introduction
Light Sensor Infrared light adjustment
Lens  Capture videos
 Infrared LED Additional light in Low-light conditions
 Monitor  Clock display
Description Introduction
Micro SD Card Slot Support Micro-SD card storage(up to 64G)
Type-c Plug in the connector of the power supply
USB2.0 5V1A Output
QR Code Label Product information
RST/RESET Press and hold [RST/RESET] for 5seconds, the device is restored to

the factory default setting
---|---
MODE| Mode set button
UP| Up button
DOWN| Down button

 Wireless Charger Camera function

Plugin with original power adapter, the device is powered on.

Clock Mode
– Press [MODE] to enter the clock setting, the hours LED will flash, then press [Up] and [Down] to set the hours . . After finishing the setting of hours, then press the [MODE] button again, the minutes LED will flash, press [UP] and [Down] to set the minutes. After finishing the setting of minutes then press the [MODE] button again, the week LED will flash, press [UP] and [Down] to set the week. – Finally, press [MODE] to apply and finish the time setting.

Set Alarm

Long press [UP] for 3 seconds to enter the clock alarm setting, the hours LED will flash, then press [UP] and [Down] to set the hours. Press the [MODE] button again, the minutes LED will flash, press [UP] and [Down] to set the minutes. Finally, press [MODE] to apply and finish the information screen. . A total of three alarms can be set. When the alarm sounds, you can press any button or tap the device to turn off Clear Alarm Long press [Down] for 3 seconds to enter the clear clock alarm setting. Rest Screen Long press [MODE] for 5 seconds to enter the screen setting, Press any button to light up the screen. Brightness Adjustment

Brightness Adjustment

Press and hold [UP] for 5 seconds, you will hear a beep of’ DI”, and then enter the screen brightness adjustment, low, medium, high (default is low)

Reset

Press and hold [RST/RESET] for 10 seconds, the device is restored to factory default setting.
Day and night light-sensitive detection

  1.  When it is dark, the screen will automatically turn off, and when it is detected that it is dawn, the screen will automatically display (automatic mode)
  2. When it is dark, the screen will be automatically turned off by default, and the display will be on forever by pressing any key; if the power is turned off and on again, it will enter the automatic mode Remarks: If you press and hold the [MODE] button for 5 seconds to enter the screen to go out, press any button and the screen is normal

Packing List

Open the package, then make sure the wireless charger camera (device) is intact, and with all the below accessories.

  Warm Tips
The use of a non-original power adapter may cause instability of the devices or WiFi disconnection. To ensure the normal operation of the equipment. please use the power adapter provided by the original manufacturer.

Preparation

Please prepare the below stuff before you use it.
One smartphone or tablet PC(Mac or Windows PC is not acceptable) with IOS 12.0 or Android 8.0 system(higher version system is acceptable)
Wi-Fi Router

  • The device can only connect to a 2.4G Wi-Fi router.

  • Make sure to turn on the DHCP of the router, and the MAC address should be off.

  • Distance between the router and the device should be within 3m
    during configuration.

  • Please don’t use special characters such as Chinese. symbol to name the WiFi.

  • Please don’t use special characters such as Chinese, symbols as the password for the WiFi and Wi-Fi password can not be blank.

Install ” IOTLiving ” App

https://play.google.com/store/apps/details?id=com.goodflys.iotliving

0peration Instruction

Wait for 60 seconds after plugging in,  the device starts and the red LED indicator will blink.

WARNING

  • Make sure to use the adapter provided to power the device.
  • Please remove the adapter in a thunderstorm to avoid possible damage.

Configure Device

Open the App

WARNING

  • If the red LED WiFi light does not blink, please switch off and turn on the device again.
  • If still red WiFi light not blink, please press IRST/SETI button at the backside and hold it for 5seconds, the device goes back to the default. Wait for 60 seconds, the device will restart.

Turn the volume of smartphone or tablet PC to the maximum.
• Wait for about 60 seconds, the configuration will be done.(After the configuration is successful, the green LED indicator will be off in about 60 seconds.)

If configuration failed

  • Please make sure to input the right password(check the capital&small letter, blank)
  • Please keep the distance between the device and the WiFi router within 5m.
  • Press and hold (RESET] for 5 seconds, the device is restored to a factory default setting, repeat the configuration again.

Watch video

 If the live video is frozen, please close it and open it again. If it is still frozen, please power off and restart the device and the WiFi router, and keep the device and the WiFi router within 3m to configure again.

WARNING

  • Make sure the Wi-Fi is connected to the Internet.
  • Make sure the smartphone/tablet PC is in the same Lan.
  • Make sure to input the right password.

Option 2: The device and smartphone are not on the same Lan.

WARNING
Please make sure the device and smartphone or tablet PC are connected to the Internet.
• Make sure the ID of the device is right. Make sure the password of the device is right.

Switch Wi-Fi connection

When you want to change from the original Wi-Fi connection to another Wi-Fi connection please reset the wireless charger camera first by the following steps:
Press and hold (RST/SET) for 5 seconds. Then release the button and then wait for 40 seconds. After the device startecLif, the red LED indicator does not blink, please reset the device to the factory default setting. Now you can connect a wireless charger camera to the network.

Micro SD card user caution

  • To ensure SD card video recording works steady, we recommend Class 10 or above version high-speed Micro SD card.
  • To make sure the device works normally, please format the SD card before the first time used.
  • Before inserting or pulling out the SD card, please power off the device. Insert the SD card properly into the slot as below.

FAQ

  • Q: Should I have to plug the USB power all the time?

    Yes, because there is no battery, please plug in the USB power all the time.

  • Q: How many users can watch the video at the same time?

    5 persons maximum.

  • Q: Whether the device supports ONVIF?

    Yes, it is standard.

  • Q: How many cameras does the App holds at the same time?

    To make sure the App works well please do not connect over 10 cameras.

  • Q: Can I record the live video on my phone?

    Yes, the manual record will be saved into your phone. But the auto-record will save into the SD card.

  • Q: Whether the device supports SD video recording?

    Yes, up to 64G Micro-SD card.

  • Q: How long does my SD card can record?

    If your camera is running Full-Time recording, one 32G SD card can record for about 4 days.if the SD card is no space for a new video, it will erase the oldest video to save the newest.

  • Q: What is the format of the video recording on the Micro-SD card?

    AVI, H.264, and most of the main media player format.

  • Q: How to use a smartphone to watch the SD card recording?

    Press the APP, press the local recording.> “SD”, then you can watch the video recording.

FAQ

  • Q: Can I turn off the Night Vision?

    Yes, Open App–Enter the view screen–click the Gear icon–Click the Infrared Light setting–Select OFF.

  • Q: Why system prompt that the wireless charger camera is offline after being added?

    Please click software”connector to check whether the wireless charger camera power supply and the network connection are OK.

  • Q: Why stuck and time-lag situations happen sometimes when watching the video?

    Please check your network connection or set up video quality to low” pattern under the advanced setting.

  • Q: What can I do if I forgot the wireless charger camera password?

    Press the [RST/SET] button on the unit and hold 5 seconds at least, the device will be reset to the factory default setting in about 40 seconds.

For more questions, please open App and click “FAQ”

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

About the User Manual:
The user manual is used as a guide
The photos, graphics, charts, and illustrations provided in the user Manual are only used to explanation and interpretation, which may be different from specific products, please refer to the real object. The user manual may be updated because of the product’s version upgrade or other requirements, if you need the latest version of the user manual, please contact customer service for the latest version of the user manual.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals