RYER CLEANER4 Ultimate Stain Cleaner Instruction Manual

SPOT CLEANER ULTIMATE
INSTRUCTION MANUAL

IMPORTANT SAFETY INSTRUCTIONS

Before using the product, please read the instruction manual carefully and keep it for future use.

• Before using, please check and make sure the voltage indicated at the bottom of the product is the same as the voltage used.
• Please do not use the appliance to suck objects such as glass, needles, gasoline and others.
• Please do not use the appliance to suck burning objects such as cigarette ends, matches or ashes with residual heat.
• Please keep the appliance away from fire sources and other high-temperature places.
• Please do not bend, tread or drag the hose forcibly. Do not continue to use the appliance if the hose is broken.
• When using the appliance, please do not block the suction inlet to prevent from causing motor failure.
• Please do not use the machine to suck small particles such as cement, gypsum powder and calcimine to prevent from causing malfunctions such as blockage of machine and damage of motor etc.
• The product can not be used for sucking large amounts of water.
• The air outlet shall not be blocked to avoid affecting the effect of heat dissipation.
• Check the hose regularly, and do not use the hose if it is damaged.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
• Before cleaning or maintenance, remove the plug from the socket to prevent accidental electric shock.
• Do not immerse the appliance into water for cleaning to avoid danger.
• The use of accessory not recommended by the manufacturer may cause injury to persons or damage to the appliance.
• Do not use outdoors.
• Appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children should be taken good care of to ensure that they do not play with this appliance.
• Children should not be responsible for the cleaning and maintenance of appliances without supervision.
• The appliance must be powered off before cleaning and disassembling as well as when it is not used.
• Children are not allowed to use the appliance without supervision.

NOTE: The current-carrying pipe contains electrical connection.

KNOW YOUR SPOT CLEANER

The company reserves the right to change the design of the product. The product you purchased may have been improved and it may be not completely the same as the instruction manual. Please subject to the real object without further notice. However, the performance and operating method will not be changed completely. Please rest assured to use it.Description control panel

Description for water spray/steam button

1. The water spray/steam button is used for releasing steam under “Steam clean mode” and “Steam sterilize mode” (see Fig.1).
2. The water spray/steam button is used for spraying water under “Low-temperature clean mode” and “High-temperature clean mode” (see Fig.2).

PRODUCT INFORMATION

HOW TO USE THE SPOT CLEANER

NOTE: The product has audio prompt function. Please pay attention to the audio prompt during using.
Operation step

1. Before using, move the machine to the working table by the handle. Remove the handle of the brush and remove the hose from the cord winding rack (see Fig.3).

2. Install the steam brush head (with the brush head cover attached) onto the handle of brush by operating the brush fastener (see Fig.4).

3. Pull the power cord from the auto cord-winding rack (see Fig.5).

4. Remove the clean water tank from the machine and open the water tank silicone plug, and then fill the clean water tank with clean water not exceeding the maximum water level.
   Finally, close the silicone plug and install the clean water tank onto the machine (see Fig.6).Do NOT put any detergent inside the spot cleaner / water tanks to avoid leaking and dangerous situations. Only use the detergent on the fabric itself.

5. Insert the power plug into the socket and then press the power switch to turn on the appliance (see Fig.7).

6. Touch the corresponding button to select the desired working mode, which includes “Steam clean mode”, “Low-temperature clean mode”, “Steam sterilize mode” and “Hightemperature clean mode” (see Fig.8) .

7. Press the switch button on the handle of brush, the indicator of the switch button illuminates solidly and the appliance starts to work according to the selected working mode.
   Press the switch button again, the appliance enters into the delay shutoff status and the indicator of switch button flashes. And the indicator of switch button will extinguish after the switch button is turned off (see Fig.9).

8. During working process, when need to spray water or release steam, hold and press the water spray/steam button on the handle of brush to enter into the working status of spraying water or releasing steam. To exit from the current working status, release the water spray/steam button (see Fig.10). NOTES:
   (1) It is normal that a little bit of water sprays out before releasing steam.
   (2) It is normal that the stopping of water-spraying or steam-releasing will delay after the water spray/steam button is released.
   (3) To avoid dangerous situations, do not remove the brush head/make any changes to the brush head when the spot cleaner is on. To do this, first switch off the cleaner and remove the plug from the socket.

9. After you finish working with the spot cleaner, press the switch button on the handle of the brush to exit from the working status, and then press the power switch to turn off the appliance (see Fig.11).

10. Press the auto cord-winding button to put the power cord away and fix the plug on the fastener, and then wind the hose on the cord winding rack neatly (see Fig.12).

11. Drain the water in the clean water tank and dirty water tank respectively and then clean them well to avoid breeding bacteria (see Fig.13).

Refill operation for clean water tank

1. During working process (spray water or release steam), the appliance will produce audio prompt and the current function will be canceled as well as the refill indicator of clean water tank will flash if the clean water tank is in lack of water, at that time, the clean water tank needs to be refilled (see Fig.14).
2. Remove the clean water tank from the appliance (see Fig.15).
3. Open the silicone plug of the clean water tank and fill the clean water tank with water through the water inlet until it is filled with water (see Fig.16).
4. Install the clean water tank onto the appliance correctly and then press the switch button to activate the appliance, after it, press the water spray/steam button to spray water or release steam according to your demand (see Fig.17).

Clean operation for dirty water tank

1. The appliance will produce audio prompt and the full indicator of dirty water tank will flash if the dirty water tank is full of water, at that time, the dirty water tank needs to be drained (see Fig.18).
   NOTE: The current working of the appliance will be stopped if the appliance detects the dirty water tank is full of water.

2. Remove the dirty water tank from the appliance (see Fig.19).

3. Pour the dirty water from the dirty water tank from the two small outlets at the top and then open the knob at the bottom, after doing this, refill the dirty water tank with clean water to perform cleaning. After finish cleaning, empty the water in the dirty water tank (see Fig.20).

4. After the dirty water tank is cleaned, close the knob and install the dirty water tank onto the appliance (see Fig.21).
   NOTE: If you want to continue using the appliance, press the switch button again.

5. If the appliance provides a audio prompt that the dirty water tank is full, but the dirty water tank is not full actually, which is a false alarm. At that time, the user shall remove the dirty water tank and clean the small metal post at the side of the dirty water tank and the metal plate corresponding to the main body. After cleaning, install the dirty water tank onto the appliance well (see Fig.22).

6. After the metal post and metal plate are cleaned, if there is false alarm produced, please clean the dirty water tank completely again and then install it well in position again (see Fig.23).

Operation for descaling

1. When the appliance provides descaling prompt, please remove the handle of the brush and then detach the brush head (see Fig.24).
   NOTE: If the descaling operation is not carried out, the user can continue to select the desired function to operate. However, if the descaling operation is not carried out after a period of use, the appliance will prohibit the use of other functions. Normal use can only be recovered after a normal descaling is performed.

2. Place the handle of the brush at a place where the water can be drained easily (drain tank) and then fix the handle of brush well in position (see Fig.25).

3. Mix the citric acid scale remover with water in the proportion of 1:20, then pour the mixed solution into the clean water tank, after it, install the clean water tank well in position (see Fig.26).

4. Press the switch button and then start to perform descaling (see Fig.27).

5. After the descaling is completed, clean the clean water tank and then install the brush head and the handle of the brush well in position, after this the appliance can be operated normally again (see Fig.28).

Removal and cleaning of the brush head

1. Before operating, make sure the appliance is powered off and cooled down completely (see Fig.29).
2. Press the fastener and then remove the brush head (together with the brush head cover) (see Fig.30).
3. Remove the brush head cover from the brush head (see Fig.31).
4. Wipe the brush head with a wet soft cloth dipped with detergent which is of no irritation (see Fig.32).
5. Remove the filter for the handle of the brush and rinse it with clean water (see Fig.33).
6. Finally, install the filter, brush head and brush head cover well in position (see Fig.34).
7. After the handle of the brush is installed well, if the the brush head can not spray water or there is irregular water-spraying condition when you work with the appliance again, please clean the water hole of the brush head with the following tool in time (see Fig.35).

CLEANING AND MAINTENANCE

1. The appliance must be turned off and be cooled down completely before performing cleaning and maintenance.
2. The main body can be cleaned with a wet soft cloth.
3. Never immerse the main body into water for cleaning.
4. The clean water tank and dirty water tank can be put into the water for cleaning.
5. Please empty the clean water tank and dirty water tank in advance to avoid breeding bacteria when the appliance is not used for a long time.
6. Regularly open the dust cover at the bottom of the main body and remove the cotton block for cleaning.

WE ARE HAPPY TO HELP YOU WITH ANY QUESTIONS.
+31 6 87570777
Send us a message on Whatsapp! This is not a number for phone calls.
SALES@MEDIAEVOLUTION.NL
THANKS FOR CHOOSING RYAR®

Documents / Resources

| RYER CLEANER4 Ultimate Stain Cleaner [pdf] Instruction Manual
CLEANER4 Ultimate Stain Cleaner, CLEANER4, Ultimate Stain Cleaner, Stain Cleaner, Cleaner
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>