pasapair SUNMORE Electric Patio Heater Instruction Manual

pasapair SUNMORE Electric Patio Heater

Specifications

• Model No.: SUNMORE
• Power Supply: AC 120V/60Hz
• Power Output: 1500W
• Dimensions: 34.056.293.38in (86.5cm16cm 8.6cm)

Product Usage Instructions

Installation

Before installing the infrared smart heater, please ensure you have the following tools:

• Pencil
• Hammer
• Level
• Screw Driver
• Power Drill and drill bits

1. Attach the L shaped bracket to the desired location using the screws and nuts provided.
2. Mark two holes on the wall using the L shaped bracket as a guide.
3. Drill holes in the marked locations using a drill bit smaller than the plastic anchors.
4. Insert the plastic anchors into the drilled holes and tap them flush with a hammer.
5. Attach the mounting bracket to the wall using screws and the holes with plastic anchors.
6. Securely fasten the heater onto the L shaped bracket using wing nuts on the back of the heater.
7. Ensure that the heater is mounted at least 2.4 meters (94.5 inches) above the floor grade.

Note: Do not pass any cables through the mheater.

Remote Control

The infrared smart heater comes with a remote control that provides the following functions:

• Turn ON or turn OFF the heater
• Push the button repeatedly to decrease power level/timer
• Push the button repeatedly to increase power level/timer

FAQ

Q: Can I dispose of this product as regular waste?
A: No, this product contains recyclable materials. Please contact your local municipality for the nearest collection point.

Q: Can I use an adapter to connect the heater to a two-slot Mreceptacle?
A: Yes, an adapter is available for connecting three-blade grounding-type plugs to two-slot receptacles. The green grounding lug on the adapter must be connected to a permanent ground.

Q: What is the recommended mounting height for the heater?
A: The heater should be installed at least 2.4 meters (94.5 inches) above the floor grade.

Q: Can I pass cables through the heater?
A: No, cables should not pass through the heater.

Model No.: SUNMORE
Power Supply: AC 120V/60Hz 1500W

PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATING THE APPLIANCE

Warning
THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE,
We cannot be liable for any damages caused by failure to observe these instructions.

IMPORTANT SAFETY INSTRUCTIONS READ CAREFULLY-The infrared heater is designed for safe operation. Nevertheless, installation,maintenance and operation of the heater can be dangerous. Observing the following procedures will reduce the risk of fire, electric shock, injury to persons and keep installation time to a minimum. Save these instructions for future use.

1. Read all instruction before using this heater.
2. Remove the unit from it’s packaging and check to make sure it is in good condition before using.
3. Do not let children play with parts of package (such as plastic bags).
4. Check the household voltage to ensure it matches the heater’s rated specification.
5. Check the power cord and plug carefully before use, to make sure that they are not damaged.
6. Before unplugging the power cord, be sure to turn off the power, when turning on the heater, be sure your hands are dry to prevent from electric shock.
7. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9 m) from the front of the heater and keep them away from the sides and rear.
8. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
9. Do not use near or in the immediate vicinity of a bath or swimming pool or any source of liquid.
10. To protect against electric shock, do not immerse cord or plug in water or any other liquid.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause an electric shock, fire or damage to the heater.
12. Always unplug the heater when not in use.
13. Connect to properly grounded outlets only.
14. Always plug heaters directly into a wall outlet/receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
15. Do not allow cord to overhang the counter top where it can be easily pulled by children.
16. Do not put fingers or foreign objects into the grill while in operation.
17. Do not leave the appliance unattended when in use.
18. This heater is not intended for use in bathrooms, laundry and similar indoor locations, never put heater where it may fall into a bathtub or other water container.
19. No liability can be accepted for any damage caused by non compliance with these instructions or any other improper use or mishandling.
20. This appliance is not intended for use by persons (including children) with reduces physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children and vulnerable people should be supervised to ensure they do not play with the appliance.
21. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
22. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Disconnect power at service panel and have heater inspected by a reputable electrician before reusing. If the supply cord is damaged in any way, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
23. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
24. To disconnect heater, turn controls to off, then remove plug from outlet.
25. To prevent overheating of this appliance, keep the air inlets and outlets clean and free of anything that may cause blockage. Check all inlets and outlets from time to time to ensure it is clear of any dirt or dust accumulation. DO NOT COVER.
26. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
27. Parts of the heater may exceed 200℃ , contact with the heating tube, reflector, or metal parts near the heating tube, may cause severe BURNS . To avoid burns, do not let bare skin touch hot surface.
28. NEVER place hands under the heating elements. ALWAYS allow heating element to cool at least 10 minutes before touching the heating tube or adjacent parts.
29. This product contains recyclable materials. Do not dispose this product as unsorted municipal waste. Please contact your local municipality for the nearest collection point.

INTRODUCTION

The SUNMORE carbon infrared heaters produce instant and comfortable heat like the sun. These robust and weatherproof heaters are designed for domestic and commercial heating applications within indoor and outdoor areas.

86.5cm16cm 8.6cm

This heater is for use on 120 volts. The cord has a plug as shown at A in Figure 68.1. An adapter as shown at C is available for connecting three-blade grounding-type plugs to two-slot receptacles.
The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available.

INSTALLATION

Tools Needed :

• Pencil
• Hammer
• Level
• Screw Driver
• Power Drill and drill bits

A mounting bracket is provided with the heater which has been specifically designed to allow this product to be fitted to ceiling before drilling the holders for the ceiling is solid and that there are no hidden water pipes or electric wires.

ATTENTION! The appliance must be installed on the solid surfaces like concrete, wood or metal etc.
Important: Ensure that the supply cables is well mounted and that it does not come into contact with reflector of the heater or that does not trail into heated area, the supply cable can be fixed to the metal mounting bracket behind heater with plastic zip ties.

1. This heater should be installed by a competent person, i.e. a qualified electrician.
2. Always disconnected the heater from the electricity supply and allow it to cool before installation.
3. This heater can be mounted in a horizontal or vertical manner, but for a higher efficiency we recommend horizontal usage.
4. For ceiling mounting, the lowest part of the heater must be located at or above a minimum height of 2.4m/94.5” from ground level, so that the heater cannot be touched when in operation.
5. For ceiling mounting, there must be a 2.4m/94.5” distance from your appliance to the ground.
6. For both horizontal and vertical mounting on the ceiling, there must be a min. distance of 0.4m/15.8” between the appliance.
7. The distance from your appliance from the corners should be min. 0.4m/15.8” for vertical use and min. 0.5m/19.7” for horizontal use.
8. When installed to the ceiling, there must be a distance of 0.5m/19.7” between corners and the appliance.
9. The distance of your appliance from the living beings is to be min 1m/39.4”.
10. The distance from the front side of the heater to materials such as wood, carton, cloth etc., must be min 1m/39.4”.
11. When mounting horizontally or to a ceiling, do not position the heater at an angle more than 90°and less than 45°.
12. The supply cable must be at the lower end of the heater if the heater is installed at an angle or vertically.
13. Keep the supply cord away from the body of the heater which will get hot during use.
14. Do not install the heater on an inflammable surface.
15. Observe the minimum safe distance between the heater body and the inflammable surfaces when mounted.
16. The heater should always have a minimum clearance of 0.5m/19.7” from the adjacent wall.
17. If the heater is to be used outside, a weather-proof outlet is recommended.
18. Before drilling, ensure that there are no wires or water pipes in the area where the heater is to be installed.
19. The heater must be installed on the mounting brackets provided.
20. Fasten the brackets securely to the mounting surface and the backside of the heater using the nuts and screws supplied.
21. Fasten the heater securely on the brackets using the nuts and bolts supplied.
22. The brackets can be used to adjust the direction of the heater, adjust the heater angle by loosening the two bolts on the wall mounting bracket, tighten the bolts again when the desired angle is reached.

Warning – to reduce the risk of fire

Caution: Keep combustible materials, such as furniture, pil- lows, curtains at least 3feet (0.9m) from the front of the heater and keep them away from the sides and rear.

Caution: Do NOT use with an extension cord or relocatable power tap (out- let/power strip).

• Hot surface, doM NOT touch.
• Do NOT cover with any objects such as blanket on the heater.

Installation Accessories:

Mounting step

1. L shaped Bracket installation
   Fasten the L shaped bracket using the screws and nuts provided (no. 4, no.5)

2. Mark holes on the place where the heater to be mounted with a pencil, use the L shaped bracket to mark each 2holes distance.

3. Drill holes with a smaller diameter drill bit than the plastic anchors

4. Insert the point end of plastic anchor into the holes, Tap the anchor with a hammer until the anchor is flush

5. Using a screwdriver attach the mounting bracket to the holes which with plastic anchor inside.

6. Fasten the heater on the L shaped bracket with wing nuts on the back of heater

7. Ceiling Mounting Height: maintain at least 2.4m / 94.5” distance from the heater to the ground as below shown.

The heater is designed with tip-over protection circuit. For ceiling-mounted, the adjustment range is 15 ° angle. The heater’s working angle is between 45 ° – 60 ° as shown in below. When the heater exceeds a 60 ° angle, it automatically turns off, but suggest mounted within 45 ° for a better choice.

THE HEATER SHOULD NOT FACE VERTICALLY TO THE FLOOR

Attention: cable should not pass through the heater

The heater must be installed at least 2.4M above the floor grade Attention: cable should not passing thought the heater.

REMOTE CONTROL

Control Functions

Noted: All heaters and their remote controls have the same frequency, so it is possible to control several heaters with just one remote.

Inserting Batteries(not included)

Insert 2 AAA/ Alkaline type batteries into your remote control

1. Flip the backside of your remote control and pull out battery cover. Insert the batteries in accordance with the instructions and polarity the batteries.
2. Change the batteries in the same way depicted above.

NOTICE:

1. Replace the old batteries with the same type batteries. Otherwise, your heater may not function well.
2. Pull out the batteries in case of long terms of disuse to prevent leakage which may impair your remote control.
3. Do not allow water or liquid to get into the remote control.

Caution:
When the appliance is not operated for a long period of time, cleaning or maintenance is conducted or when the location of the heater is changed, the heater should be turned to OFF and unplugged from the electrical connection.
Periodic inspection and removal of dirt and contaminants will ensure that equipment can be operated safely.

LED Display

Button Switch:

Step 1: Plug in the heater

Step 2: Turn on the button switch , the product is in standby mode display (- -); adjust the heating level L1-L3 by repeatedly pressing the button switch .

TROUBLE SHOOTING

1. Check if the power cord is plugged into an electrical outlet, if not, plugged in.

2. Check if electricity to the main fuse is working.

3. “ E1 “ Error on display（Over heat protection）
   Step 1: pull the plug out
   Step 2: wait 1 hour until heater cool down
   Step 3: put the plug in and press the button to restart the heater
   Noted: thermostat device take action to automatically turn off the heater given the unit overheat,cooling down the heater after 1 hours and re-start the heater.

4. “ E2 “ Error on display（Tilt protection）
   Check the installation angle of the heater. Adjust the angle and restart the heater.

5. L1,2,3 shows in display, but no heat: Overheat protection or Bulb is damaged. Follow above E1 error display solution’s step, if still no heat, arrange for replacement bulb with local Dealer accordingly.

MAINTENANCE

Attention! Careful and regular maintenance of your heater considering our instructions assume
great importance so as to attain a long efficient operation of your appliance.

1. Check the filthiness of the Reflector and IR-Filament at least once a month. If necessary, apply cleaning and maintenance instructions.

2. The number of checks may be increased considering the amount of the dust in the environment.

3. Check the deformation of the Reflector, Wire and Frame visually while cleaning the appliance.
   In case of deformation, consult to your technical service.

4. Check the Power Cord and Plug visually while cleaning the appliance. In case of deformation, consult to your technical service.

CLEANING

Regular and careful cleaning helps your infrared heater operate efficiently for many trouble free years. To clean your heater follow steps below:

1. Unplug the power cord for your safety before cleaning your appliance.
2. Make sure the heater is cool before continuing.
3. To keep the heater clean, the outer shell maybe cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. (CAUTION: DO NOT let liquids enter the heater).
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater in water
6. Wait until the heater is completely dry before use.

Storage: Store the heater in a cool, dry location when not in use to prevent dust and dirt build up.
Use packaging carton to store.

ATTENTION:

1. Always disconnect the heater from the electricity supply and allow it to cool before attempting to work on it.
2. If the heater has collected dust or dirt inside the unit or around the heating element, have to unit cleaned by a qualified service agent. Do not operate the heater in this condition.
3. The only maintenance required is cleaning of the external surfaces of the heater.
4. Do not touch the heating element with bare fingers, as residue from your hand could affect the life of the lamp. If it is accidentally touched, remove the finger marks with a soft cloth moistened with mentholated spirit or alcohol.
5. Do not attempt to repair or adjust any electrical or mechanical functions on this heater.
6. The heater contains no user serviceable parts. Should the product suffer damage or breakdown, it must be returned to the manufacturer or its service agent.
7. Damaged supply cords to be replaced by the manufacturer, service agent or similarly qualified person in order to avoid hazard.

RECYCLING
At the end of the electrical products useful life it should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice in your country.

Manufacturer:HEYUAN XINDA QUARTZ ELECTRIC APPLIANCE CO., LTD.
Add.:Inside Linjiang Industry Park, Economy Development Zone, Jiangdong New Zone,Heyuan, Guangdong, China
Contact: Joyce Email: info@pasapairhome.com

WARRANTY

Thank you for choosing PASAPAIR product. We sincerely hope that you are satisfied with it.
The manufacturer’s warranty covers the product for a period of 12 months from the date of purchase against manufacturing faults. All warranties are automatically kept track of in our system, so there is no need to register your product.
Agent/Distributor is welcome to contact us. Email: info@pasapairhome.com.
Any help or questions during use, please contact us via website www.pasapairhome.com, send email to info@pasapairhome.com, , we will service you within 24 hours. We suggest to provide a warranty card, a photo or a video if there’s broken spare part or not working machine so that we can be much more clear about your problems and offer you the best solution.

Email:
Buyer’s name:
Address:
Tel.:
Order Number:
Purchase date:
Item name:
Model:
Serial No .

Please fill in the table and email it within 10 days from the date of purchase.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>