Poemoon P42-600G1 Elegant Chandelier Crystal Dining Room Light Fixture Instruction Manual

Poemoon P42-600G1 Elegant Chandelier Crystal Dining Room Light Fixture

Overview

WARNING : TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR REMOVE THIS FIXTURE.

NOTE: Please carefully check all the mounting accessories are complete before installation, if you are missing any accessories, please feel free to contact us through email.

Part List

Washer

| 3
a5|

Expansion Bolt

| 3
b6|

Fabric Cord Cover

| 1
f1| | 84
g1| | 128
|

Glove

| 1

Tools Required

|
---|---
|
|
|

Electrical test reminder

• Test the electricity of the light fixture first before installing, and if it can be properly functioning please follow thesteps1-6asbelowtoinstall.
• Any Questions About the installation process, please contact the mail address at the bottom of the first page, prompt response will be offered within 24 hours.

INSTALLATION STEPS

Step 1 ( Install the mounting bracket )

• Turn off the light power supply at the circuit breaker box and the wall switch.
• Fix the mounting bracket to the ceiling. There are two types of screws included in the accessories bag. Use them in different types of ceilings.

1. For outlet box that is ACCEPTABLE FOR LIGHT SUPPORT
   
   a. Unscrew out the hollow screw(b2) and hex nut(b3) from the pendant chain(B).
   b. Thread hollow screw through the hole position of mounting bracket(a1) and fix it with hex nut(b3).

c. Pull out all wires from the outlet box, then match the holes on the mounting bracket with the outlet box.

d. Use mounting screw(a2) to fix the mounting bracket.
e. Cover the canopy(A), install the metal ring(b4) to the hollow screw(b2).

Step 2 (Installation of tubes)

As the picture 2a show :

a. Take out the screws(d1) and the screws(d2) on the tubes(D).
Note: The hole position for installing the tube is a large hole position.
b. Put the tube align the large screw holes, then drill the screws(d1) into the iron frame(E) thought the screw holes to fixed it.
c. Repeat the above action and secure the remaining three as well.

Step 3 (Installation of lamp body)

As the picture 3a show :

a. Put the tubes(D) align the screw holes, then drill the screws(d2) into the lamp body(C) thought the screw holes to fixed it.
b. Repeat the above action and secure the remaining three as well.

Step 4 (Organizing the wires and adjusting the chain length )

a. Before the installation, please adjust the length of the pendant chain first. Use a plier to remove pendant chain(B) to shorten the chain.
b. All wires need to pass through the pendant chain(B), not all chain rings are necessary.

c. Use the pendant chain to connect the lamp body(C) by rotating the O-Ring(b5) to metal ring(c1),

Step 5 (Connecting wires )

a. Loosen the decorative fastener(b1) from the metal ring(b4) , remove the canopy(A) .
b. All wires need to pass through the metal ring(b4) and canopy(A) .
c. Connect the indoor live wire with the black wire(L) of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.
d. Connect the indoor natural wire with the white wire(N) of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.

e. Connect the indoor ground wire with the ground wire of the light fixture by twisting two wires together, then use the wire nut(a3) to twist them together.
f. Use the wire tape to tie all the wires for a secure connection, then put all the connected wires into the outlet box.
g. Put the canopy (A) onto the outlet box and let mounting bracket go through the holes on the canopy, then use metal ring and decorative fastener to tighten them up.

Step 6 (Installation of triangular prisms and crystal prisms )

a. the T- Buckle(f1) pass through the triangular prisms(F) , then pass through the reserved holes on the lamp body(C) and break open both sides of T- Buckle to secure it.
NOTE : When fixing triangular prisms with T-Buckle, leave some space and do not tighten too tightly.
b. Connecting crystal prisms(G) and lamo body(C) with butterfly buckle(g1).
c. Connecting crystal prisms(G) and iron frame(E) with butterfly buckle(g1).
d. Install E12 bulb. turn on the power supply. turn on the light switch.

Troubleshooting

WARNING : Make sure the power is off at the electrical panel box before attempt any repairs. If any problems or dissatisfaction during using, please contact us: E-mail:banleris@163.com.

Test or replace the switch.
Check the wiring.
Replace the lightbulb.
The fuse blows or the Circuit breaker trips when light is turned-on.| Check The wire connection.

Careand Cleaning

Disconnect power to the fixture by turning off the circuit breaker or byre moving the fuse at the fuse box.
Used Ry or slightly dampened clean cloth to wipe the interior surface of the fixture.

CUSTOMER SUPPORT

If you have any problems or dissatisfaction, Please feel free to contact
E-mail:banleris@163.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>