Aureday B0CGXXJBHN Mobile Phone Clip Fill Light User Manual
- May 15, 2024
- Aureday
Table of Contents
Aureday B0CGXXJBHN Mobile Phone Clip Fill Light
Safety Notice
Before operating this device, please read the following instructions carefully and keep them for future reference o
Product structure introductions and function buttons location description
- Light board (light-emitting area)
- Angle adjustment knob ( adjust the angle tightness)
- Clip (fixed on mobile phones or laptops)
- Latch port ( expand external device)
- Lens fixing hole (phone lens and laptop lens)
- Brightness increase button ( each time you press the brightness increase button,
- The brightness will increase by 10°/o, up to 100o/o) Brightness decrease button (every time you press the brightness decrease button , the brightness decreases by 10°/o, the minimum is 10°/o)
- Power/mode switch button (Long press for 3 seconds to turn on and off. Single press to switch colors, warm light, white light, warm white light)
- Type-c charging interface (USB to Type-C port power cable)
- Battery indicator (flashing when charging, al\Nays on \When turned on, 4 bars \Nhen fully charged)
- Transfer pin (transfer quarter buds and phone clips)
Product installation and use
- Take out the main body of the fill light, the front clip, and insert one end of the front clip fixing clip into the fixing slot of the main body. Upon hearing the click, the front clip is 1 installed.
- Clip the fill light with the front clip to the mobile phone for fill light. To avoid blocking the camera, adjust the fill light’s position to by the clip.
- Loosen the knob counterclockwise to adjust the fill light’s angle, then tighten it by turning it clockwise.
- Press the fixing buckle of the front clip and then pull it out to remove the front clip.
- The use of the front clip
① When installing, push the bracket to the slot
② When disassembling, press the elastic buckle and pull it back to remove
Product Size
unit: inch
tolerance: ±0.1 in L=4.1 W=2.9 H=0.5
Technical reference
| Serial number | project | Specification |
|---|---|---|
| 1 | Scope of application | It is suitable for all environments that need fill |
light, such as mobile phone shooting and fill light, digital camera shooting
fill light, etc.
2| LED number| 20pcs 6500K cool color and 20pcs 3000K warm color
3| power| 4W
4| Maximum illumination| 250 LUX/0.5m
5| Color temperature mode| white light, warm light, warm white
6| Color rendering index| CRl>90
7| Dimming range| 10%-100% ten-speed adjustment
8| Power supply| Built-in 3.7v2000mAh polymer battery
---|---|---
9| Charging voltage| 5V/2A
10| Charging interface| Type-C*1
11| Discharge time| About 2-3 hours
12| Charging time| About 3 hour
13| Fixed way| Front clip (with lens fixing hole, angle can be adjusted)
14| Product Weight| 121g
15| Working temperature| 0°C-40 °C 32-10 4°F
16| Storage temperature| -10°C-S0 °C 14°F – 122°F
17| Relative humidity| 20%-90%
18| Product Size| 104X13.5X75mm
Precautions
- This fill light is not dust proof or waterproof.
- This fill light is a precision instrument, please do not let the fill light fall to the ground, subject to collision or strong impact.
- The working temperature of this fill light is 0°C -40°C.
- Do not block the ventilation holes, otherwise it may increase the internal temperature and cause a fire or accident, which may cause an accident to the fill light.
- Do not look directly at the white LED in use at close range, otherwise it may damage your eyesight.
- Do not place this fill light near flammable or easily produced solvents, otherwise it may send and receive fire or generate smoke.
- When the fill light is finished, be sure to turn the switch to “OFF” to turn off.
- Do not put the fill light in the storage box after use, the white LED may be damaged by the residual heat. The fill light must be fully cooled before placing it in the storage box.
Customers Support
Contact us: [email protected]
Official Website：www.aureday.net