GLOBAL INDUSTRIAL 241728/241729 Tilting Work Stand User Manual
- June 4, 2024
- GLOBAL INDUSTRIAL
Table of Contents
GLOBAL INDUSTRIAL 241728/241729 Tilting Work Stand
Product Description
Please read and save these instructions, read carefully before attempting to
assemble, install, operate or maintain the product described. Protect yourself
and others by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property damage! Retain
instructions for future reference.
Description
Lift table are designed for use in shipping and receiving rooms, warehouse
stock rooms ,shops, laboratories, stores, etc. Each unit comes equipped with
steel platform, adjusting knob, base frame, 4” polyurethane casters, and all
mounting hardware.
Specifications
- Model Load Capacity(lbs/kg) Platform Size (in/mm) Net Weight(lbs/kg)
- W L
- TWS150 150/70 22/558 21/530 55/25
- TWS300 300/140 24/609 24/609 80/36
CAUTION Never exceed the maximum capacity of the lift table
- Keep hands and feet away from all moving parts while table is in use.
- Do not attempt to adjust the height or tilt angle of the table while a load is sitting on the platform；
- Place table on level stable ground. Never stand or sit on the table
- Remove load before performing any repairs on the table
- Use only maintenance parts supplied or approved by the manufacturer。
- Always engage all wheel brakes when table is not being moved
- Load must be evenly distributed on table to ensure maximum stability
- Always make sure the height adjustment screw is securely tighten before a load is applied especially after table has been raised or lowered.
- Failure to follow these guidelines may result in personal injury and /or property damage.
Unpacking
Upon receipt, visually inspect for product damage. If damage is evident, notify delivering carrier immediately and file necessary claims.
Operation
TWS150
- Position the work table near the desired work area.
- Lock all casters with brake.
- Adjust the height to the correct level by star knob adjustment located on the center column and sliding it up or down.
- Loosen the tilt adjustment knob under platform .Tilt deck to desired angle and retighten.
- Place the load on the table.
TWS300
- Position the work table near the desired work area.
- Lock all casters with brake.
- Loosen the height adjustment screw and adjust the work table to the desired height using the handwheel located on the base
- Tighten the height adjustment screw.
- Adjust the tilt angle of the table to the desired position using the handwheel directly under the table platform.
- Place the load on the table.
CASTER INSTALLATION INSTRUCTIONS
Securely prop up one end of the carts frame high enough for the casters to fit
underneath that end. You will see four caster mounting brackets welded to the
bottom of the carts frame, one at each corner. If you have both swivel and
rigid casters, the casters are to be mounted in adjacent pairs, Typically ,the
swivel casters are mounted to the side on which the push handle is located(
when applicable), Determine the proper locations for the casters before you
begin Turn the included machines screws a couple of threads into the two
threaded holes in the ends of each of the caster mounting brackets To install
the casters onto the cart: Insert either of the short sides of the caster’s
top plate into the curled end of the caster mounting bracket. Raise the other
end of the caster’s top plate up into the mounting bracket, and secure it
there by screwing in the machine screws completely. The screws should
underneath the caster’s top plate , thereby retaining it in the bracket.
For Repair Parts
Please provide following information:
- Model number
- Serial number(if any)
- Part description and number as shown in parts list
Repair Parts List for Lift Table TWS150
Repair Parts illustration for Lift Table
Repair Parts for Lift Table TWS300
Documents / Resources
|
GLOBAL INDUSTRIAL 241728/241729 Tilting Work
Stand
[pdf] User Manual
241728 241729 Tilting Work Stand, 241728, 241729, Tilting Work Stand, Tilting
Stand, Work Stand, Stand
---|---