ErgoFocus EF101B Single Monitor Mount Arm User Manual

ErgoFocus EF101B Single Monitor Mount Arm

Product Specifications:

• Load Capacity: 4.4~19.8 lbs (2~9 kg)
• Desk Specifications:
  • C-clamp: 0.39~2.36″ (10~60mm)
  • Grommet: 0.39~2.76″ (10~70mm)
• Product Dimensions:
  • Base Dimensions: 6.3″x2.1″ (160mm x 53mm)
  • Height Adjustment: 7.6-11″ (192mm-280mm)
  • VESA Plate Size: 2.95″x4.4″ (75mm x 112mm)
  • Maximum Arm Reach: 12.2″ (310mm)
  • Clamp/Grommet Range: 0.39~2.76″ (10~70mm)

Product Usage Instructions

Must Check Before Getting Started:
Before installation, verify your monitor and desk specifications to ensure compatibility.

Base Installation:
Option A: Clamp Installation

1. Detach the clamp (F) with the 4mm Allen key (J).
2. Install the clamp (F) to the bracket (E) using the 4mm Allen key (J).
3. Mount the clamp (E) to the bottom of the base (C) by tightening bolts (G) with the 4mm Allen key (J).
4. Secure the stand to the desktop by tightening the clamp (F).

Option B: Grommet Base Installation

1. Detach the clamp (F) with the 4mm Allen key (J).
2. If there is a plastic protector on the existing grommet hole, remove it.
3. Mount the carriage bolt (I) to the base (C) by hand.
4. Run the carriage bolt (I) with the base (C) through the grommet hole on the desktop.
5. Secure the base to the desktop using the clip plate (F4) and wingnut (H).

Attach VESA Plate to Monitor:

1. Select the correct screw length based on monitor thickness.
2. Attach the VESA plate to the monitor using the appropriate screws and washers.

Frequently Asked Questions (FAQ):

• Q: What should I do if I encounter missing parts during installation?
  A: If you discover any missing parts, please contact Customer Service for assistance before proceeding with the installation.

• Q: Can this product be used outdoors?
  A: No, this product is intended for indoor use only. Using it outdoors may lead to product failure and personal injury.

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

BEFORE ASSEMBLY

• Please check and make sure all necessary accessories are included and undamaged.
• Please read and understand this manual carefully before installation.

WARNING

• This product contains small items that could be a choking hazard if swallowed. KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
• Improper installation, such as using the product for monitor over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.

CAUTION AND MAINTENANCE

• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).

Must Check Before Getting Started

Verify Your Monitor Specifications

VESA Pattern (W x H):

• 75mm × 75mm / 3″ × 3″
• 100mm × 100mm / 4″ × 4″

WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended for use only within the maximum weights indicated. Use with products heavier than the maximum weights indicated may result in failure of the mount and its accessories, causing possible damage or injury.

Verify Your Desk Specifications:

Tension adjustment should be done only after monitor installation

WARNING:
Gas Spring Arm is under pressure and should be handled with care. Failure to follow the instructions may result in damage to the mount and/or personal injury.

Product Dimensions

Supplied Parts and Hardware

NOTE : Not all parts and hardware included will be used.

Base Installation

Attach VESA Plate to Monitor

Select Correct Monitor Screw Length

CAUTION : Too short will not hold your monitor. Too long will damage your monitor

Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the appropriate screws and spacers for your monitor.

Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged

Arm and Monitor Installation

1. Install the lower arm (B) to the base (C) then install the upper arm (A) to the lower arm (B). Secure the arms by tightening the inside screws using 4mm Allen key (J).
2. Remove the pre-assembled security bolt (A0) from the upper arm (A).
3. Slide the monitor onto the head of the upper arm (A), then install the security bolt (A0).
4. Make sure the security bolt (A0) is installed before you rotate the monitor

Adjustments

Tilt Adjustment

1. Loosen the tilting bolt.
2. Adjust the monitor to your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle

Tension Adjustment

The gas spring is pre-set for a load-bearing range of 8.8 lbs -13.2 lbs. For the intended functioning of the mount, you may need to adjust the tension of the Arm by your monitor weight by 6mm Allen key (K).

Note:
Be sure to keep the arm in a horizontal position during adjustment. Or else it would be difficult to adjust the mount or damage the mount

Situation 1: Arm falls down
The Upper Arm with the monitor falls and fails to stay where intended.

Solution:
Turn the inside screw counterclockwise (“+” direction) to increase gas spring tension until the arm can stay as intended.
Situation 2: Arm rises up or can’t press down Upper Arm with monitor rises up and fails to stay where intended.

Solution:
Turn the inside screw clockwise (“-” direction) to decrease gas spring tension until the arm can stay as intended.

Cable Management

Upper Arm
Run cables through the cable cover(A1), then insert the cable cover into the upper arm in the direction shown and gently push the cable cover down along the upper arm so that the cable cover is tightly fastened under the upper arm.

Lower Arm
Remove the cable cover with 4mm Allen key (J), run cables through the cable cover, and then install the cable cover again.

Adjust monitor position and rotation

Note : To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate. Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, Rotate Vigorously please do not hesitate to ask for our help.

Please do not move the stand outside the desk for safety!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>