ErgoFocus EF301B Single Monitor Mount Arm Instruction Manual
- June 14, 2024
- ErgoFocus
Table of Contents
INSTALLATION INSTRUCTION
CX03-01_V1.0
If you have any questions, please feel free to contact Customer Service via Amazon before returning.
Safety Caution
BEFORE ASSEMBLY
- Please check and make sure all necessary accessories are included and undamaged.
- Please read and understand this manual carefully before installation.
WARNING
-
This product contains small items that could be a choking hazard if swallowed.
KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED. -
Improper installation, such as using the product for monitor over its load capacity or for any purpose not explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused by improper mounting or inappropriate use.
CAUTION AND MAINTENANCE
- Never allow children to climb, stand, hang, or play on any part of monitor or stand.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
- Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Must Check Before Getting Started
Verify Your Monitor Specifications:
VESA Pattern (W × H):
75mm × 75mm / 3″ × 3″
100mm × 100mm / 4″ × 4″
WARNING
DO NOT exceed the maximum weight indicated. This mounting system is intended
for use only within the maximum weights indicated. Use with products heavier
than the maximum weights indicated may result in failure of the mount and its
accessories, causing possible damage or injury.
Verify Your Desk Specifications:
Attention
Tension adjustment should be done only after monitor installation
WARNING:
Gas Spring Arm is under pressure and should be handled with care.
Failure to follow the instructions may result in damage to the mount and/or
personal injury.
Product Dimensions
Supplied Parts and Hardware
1-A Base Installation
OPTION A: Clamp Installation
Desk Thickneess 0.39~3.35″ (10~85mm)
A-1
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm allen
key(J). Mount Bracket (C) to base (C) using bolts (M). Tighten them by using
4mm Allen key(I).
A-2
Attach the clamp (E) to the brace (D). Then tighten the bolts (M) with 4mm
Allen key (I).
A-3
Secure stand to the desktop by tightening clamp (E).
Install the decorative cover (H) to base finally.
1-B Base Installation
OPTION B: Grommet Base Installation
Desk Thickneess 0.39~2.76″ (10~70mm)
B-1
Mount base (C) to pole (B) using bolts (L). Tighten them by using 5mm Allen
key(J).
Mount carriage colt (O) to pole (B) using bolts (M).
B-2
Detach the clip plate (E4) from the clamp (E).
B-3
If existing grommet hole comes with a plastic protector, remove it to ensure a
flat surface before installing the desk mount.
Run carriage bolt (O) with base (C) through grommet hole on desktop. Secure
base to the desktop by using clip plate (E4) and wingnut (N). Install the
decorative cover (H) to base finally.
Attach VESA Plate to Monitor
2-1 Select Correct Monitor Screw Length
Which Situation Needs Spacers?
If the screw is too long or the surface is uneven, please choose the
appropriate screws and spacers for your monitor.
2-2
Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.
Arm and Monitor Installation
3-1
Install the cable clip (G) and arm (A) to the pole (B).
Fasten the bolts with 6mm Allen key (K).
3-2
Remove the pre-assembled security bolt (A0) from the upper arm (A).
Slide the monitor onto the head of upper arm (A), then install the security
bolt (A0).
Make sure the security bolt (A0) is installed before you rotate the monitor.
Adjustments (If necessary)
4-1 Tilt Adjustment
- Loosen the tilting bolt.
- Adjust monitor to your desired tilt angle.
- Retighten the tilting bolt to fix the intended angle.
4-2 Tension Adjustment
The gas spring is pre-set to minimum tension (4.4 lbs). For intended
functioning of the mount, you may need to adjust the tension of Arm in
accordance with your monitor weight by 6mm Allen key (K).
Note:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counterclockwise (“+”direction) to increase gas spring
tension until the arm can stay as intended.
Situation 2: Arm
rises up or can’t press down Upper Arm with monitor rises up and fails to stay
where intended.
Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension
until the arm can stay as intended.
Cable Management
Cable Clip (G)
Lower Arm
Remove the bottom plastic cover from lower arm as shown in the diagram. Run
cables through the cable cover, then insert and slide the cover down for
reattachment.
Adjust monitor position and rotation.
Note : To ensure stability, the tightness of the rotating axis has been
preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion : Please attach the monitor first, then hold the sides of it
with both hands, and rotate vigorously. If that doesn’t work out, please do
not hesitate to ask for our help.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>