ErgoFocus CX02-01 Monitor Wall Mount Instruction Manual

ErgoFocus CX02-01 Monitor Wall Mount

DIMENSION

If you have any questions, please feel free to contact Customer Service via Amazon before returning.

Supplied Parts and Hardware

NOTE: Not all parts and hardware included will be used.

Extra Tools You Need (Not Supplied)

Safety Caution

Please read this instruction carefully before installation. If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, please contact us.

• This product is designed for use in wood stud or solid concrete wall.

  • DO NOT install into drywall alone.

• The wall must be capable of supporting five times the weight of the monitor and mount combined. Incorrect installation may result in product damage/property damage or body injury.
  We shall bear no responsibility for any damage or injury resulted from incorrect installation, incorrect assembly or misuse.

• WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; please contact our customer service team. Never use damaged parts!

Must Check Before Getting Started

Attach VESA Plate to Monitor

Select VESA Plate Configuration

Select the configuration to use based on the measurement from monitor.
If your monitor hole pattern is greater than 100x100mm, attach extenders (F, G) to VESA plate (B) by using nuts (M-G) and bolts (M-H).

Select Correct Monitor Screw Length

Do not tighten the screws excessively or tighten them by using the Electrodrill, or your monitor might be damaged.

Attach Arm to Wall

OPTION A:
Wood Stud Installation

Install wall plate using lag bolts e with Socket Wrench, NO Electrodrill. No anchors when installed onto the wood studs.

CAUTION:
To avoid potential personal injury or property damage:
All 3 lag bolts e MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Attach Arm to Wall

OPTION B:
Solid Concrete Wall Installation

Drill pilot holes using a <1>3/8 in (Cl>10mm) diameter drill bit.

IMPORTANT:
Do not drill holes into where water pipes or electrical wires are located, or mortar between blocks.

Use the hammer to knock anchors into the concrete wall. Be sure the anchors are seated flush with the concrete surface. Install wall plate using lag bolts ‘9 and anchors S with Socket Wrench, NO Electrodrill.

CAUTION:
To avoid potential personal injury or property damage:
All 3 lag bolts ‘9 MUST BE firmly tightened to prevent unwanted movement of the wall plate assembly. Ensure the wall plate assembly is securely fastened to the wall before continuing on to the next step.

Hang Monitor

Remove the pre-assembled security bolt (AO) from the arm (A).
Slide the monitor onto the head of arm (A), then install the security bolt (AO). Make sure the security bolt (AO) is installed before you rotate the monitor.

Adjustments (If necessary)

Tilt Adjustment

1. Loosen the tilting bolt.
2. Adjust monitor to your desired tilt angle.
3. Retighten the tilting bolt to fix the intended angle.

Tension Adjustment
The gas spring is pre-set to minimum tension (6.6 lbs). For intended functioning of the mount, you may need to adjust the tension of Arm in accordance with your monitor weight by 6mm Allen key (E).

Note:
Be sure to keep the arm in a horizontal position during adjustment.
Or else it would be difficult to adjust the mount or damage the mount.

Cable Management

Lower Arm
Remove the bottom plastic cover from lower arm as shown in the diagram. Run cables through the cable cover, then insert and slide the cover down for reattachment.

Adjust monitor position and rotation.

Note: To ensure stability, the tightness of the rotating axis has been preset, so it would be kind of difficult to rotate the VESA plate.
Suggestion: Please attach the monitor first, then hold the sides of it with both hands, and rotate vigorously. If that doesn’t work out, please do not hesitate to ask for our help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>