Sunmi NC030 Cash Drawer Cable User Manual

Sunmi NC030 Cash Drawer Cable

Product Information

Specifications

• Type: Input Parameter
• Type-A USB: 5V/2A
• Bluetooth: BLE 5.0
• Indicator Light: Power indicator light & Bluetooth indicator light
• Output: RJ12 24V/1A
• Technical Features: Short-circuit detection, automatic short-circuit protection
• Supported Operating Systems: Windows (support USB CDC and BT BLE mode), Android (support USB CDC and BT BLE mode), iOS (only support BT BLE mode), macOS (only support USB CDC mode)
• Mode/Band Frequency Power: BLE 2402-2480 MHz(TX/RX) at 8 dBm

Product Usage Instructions

Driven by USB

• Supported Devices: Android POS, Windows POS
• Cash Drawer Connection: Connect the cash drawer cable to the RJ12 port to output a pulse signal to drive the cash drawer to open.
• Connection to PC/POS Terminal: Connect a PC or POS terminal to the USB port to send an instruction with the driver to open the cash drawer.

Driven by Bluetooth

• Supported Devices: Apple iPad, Android PAD, Windows Notebook
• Cash Drawer Connection: Connect the cash drawer cable to the RJ12 port to output a pulse signal to drive the cash drawer to open.
• Power Requirement for Bluetooth: Connect a 5V/2A power adapter (to be purchased separately) to the USB interface to power the device for using Bluetooth to drive the cash drawer.
• Bluetooth Setup: The Bluetooth is operational after connecting the USB port. Devices conforming to BT BLE standards can send instructions to open the cash drawer.

Indicator Light Description

is a cash drawer fault found.

FAQ

• Q: What devices are supported for Bluetooth operation?
  A: The product supports Apple iPad, Android PAD, and Windows Notebook for Bluetooth operation.

• Q: How can I detect a short-circuit fault in the cash drawer?
  A: The indicator lights will flash in case of a short-circuit fault in the cash drawer. If both green and blue lights flash, a fault is detected.

Driven by USB

1. Connect the cash drawer cable to the RJ12 port to output a pulse signal to drive the cash drawer to open;
2. Connect a PC or POS terminal to the USB port to send an instruction with the driver to open the cash drawer;

Driven by Bluetooth

1. Connect the cash drawer cable to the RJ12 port to output a pulse signal to drive the cash drawer to open;
2. To use Bluetooth to drive the cash drawer, you need to connect a 5V/2A power adapter (to be purchased separately) to the USB interface, thus to power the device;
3. The Bluetooth is in service after the USB port is connected, and devices conforming to BT BLE standards can send instructions to open the cash drawer;
   *This product doesn’t have the PD protocol function.

Indicator Light Description

green light also flashes, there is a cash drawer fault found.

Technical specifications

Short-circuit protection

| A short circuit detection will be automatically carried out after power is on and before opening the cash drawer, and the cash drawer can only be opened if no exception is detected.

OS

| Windows (support USB CDC and BT BLE

mode);

Android (support USB CDC and BT BLE mode); iOS (only support BT BLE mode);

macOS (only support

USB CDC mode).

Technical features and characteristics of the product include the following features and characteristics

MHz(TX/RX)

| 8

Disclaimer

Due to product updates, some details of this document may not conform to the product. Please refer to the real product. The right of interpretation of this document belongs to our company. We reserve the right to amend this manual without prior notice.

EU Representative: SUNMI France SAS186, avenue Thiers,69006 Lyon, France This device complies with the basic recommendations and other relevant measures in the 2014/30/EU and 2-014/35/EU directive. The full text of the EU Declaration of Conformity is available at the following internet address： https://developer.sunmi.com/docs/read/en-US/maaeghjk480.

This symbol means that it is forbidden to dispose of the product of with normal household waste. At the end of the product life cycle, waste equipment should be taken to designated collection points, returned to the distributor when purchasing a new product, or contacted by your local authority representative for detailed information on WEEE recycling.

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE : THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MOD- MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT

ISED Canada compliance statements
This device complies with ISED Canada license-exempt RSS standard(s). Operation is subiect to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device,

RF Exposure Statement (SAR)
This equipment complies with EU, FCC, and IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. Shanghai Sunmi Technology Co., Ltd. Address: Room 505, No.388 Song Hu Road, Yang Pu District, Shanghai, China

References

• developer.sunmi.com/docs/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>