Day-Brite DuaLED Recessed LED with Space Wise Technology Instruction Manual
- June 17, 2024
- Day-Brite
Table of Contents
Day-Brite DuaLED Recessed LED with Space Wise Technology
Specifications
Manufacturer | Day-Brite CFI |
---|---|
Division | Signify North America Corporation / Signify Canada Ltd. |
Address (USA) | 200 Franklin Square Drive, Somerset, NJ 08873, USA |
Phone (USA) | 855-486-2216 |
Website (USA) | www.day-brite.com |
Address (Canada) | 281 Hillmount Road, Markham ON, Canada L6C 2S3 |
Phone (Canada) | 800-668-9008 |
Website (Canada) | www.cfi-lighting.com |
Document Number | 443583098132 |
Date of Issue | AUGUST, 2018 |
Page | 1 OF 4, 2 OF 4, 3 OF 4, 4 OF 4 |
Important Safety Information
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL. ATTENTION: L’INSTALLATION ET L’ENTRETIEN DE CE PRODUIT DOIVENT ÊTRE EFFECTUÉS PAR UN ÉLECTRICIEN OU UN MEMBRE DU PERSONNEL QUALIFIÉ.
Warnings
CAUTION: Electrical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible materials can cause fire and personal contact can cause severe burns.
Installation Overview
- Install the luminaire by placing in a 2′ x 4′ ceiling grid location.
- Install seismic grid clips in holes provided.
- Make supply connections through the access plate provided in top of the luminaire.
- Access to wiring compartment is accomplished by the removal of both lenses and wiring cover. See illustrations for details.
- Remove the wiring cover by prying upper edge away from housing on both sides until the cover is free of the 2 mounting studs at each end. To reinstall the cover, spring it over the 2 studs at each end until cover is centered and fully seated.
- Remove lenses by flexing them until they become free of the housing & wiring cover. Make sure when reinstalling the lenses, that the glossy side of the lenses is inward toward LED lamps.
CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT SHOULD BE PERFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL
CAUTION: Electrical luminaires are designed for permanent installation in ordinary (Non-Hazardous) locations in accordance with the National Electrical Code and all applicable local codes. Do not use in areas of limited ventilation or in high ambient enclosures. The lamp and luminaire operate at high temperatures, contact with combustible materials can cause fire and personal contact can cause severe burns.
FAQ
- Who should install and service this product?
- Installation and servicing must be performed by a qualified electrician or service personnel.
- Where should this luminaire not be used?
- It should not be used in areas of limited ventilation or in high ambient enclosures due to the high operational temperatures.
- How can I access the wiring compartment?
- Access is gained by removing both lenses and the wiring cover.
- What should I be cautious of when handling the luminaire?
- Due to high temperatures, avoid contact with combustible materials and be wary of potential burns when touching the luminaire.
- How do I remove and reinstall the wiring cover?
- Pry the upper edge away from the housing on both sides until the cover is free of the 2 mounting studs at each end. To reinstall, spring the cover over the 2 studs at each end until it is centered and fully seated.
- What is the correct orientation for the lenses when reinstalling?
- Ensure that the glossy side of the lenses is facing inward toward the LED lamps.
Signify North America Corporation
- 200 Franklin Square Drive
- Somerset, NJ 08873, USA
- Phone: 855-486-2216
- www.day-brite.com
Signify Canada Ltd./Signify Canada Ltée.
- 281 Hillmount Road
- Markham ON, Canada L6C 253
- Phone: 800-668-9008
- www.cfi-lighting.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>