VEVOR XRSS2304 Cabinet Hardware Jig Instruction Manual

Technical Support and E-Warranty Certificate
www.vevor.com/support

XRSS2304 Cabinet Hardware Jig

CABINET HARDWARE JIG
MODEL: XRSS2304

We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
Technical Support and E-Warranty Certificate
www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY INSTRUCTIONS

1. This product contains small parts. If swallowed, it will pose a choking hazard. Keep these small parts away from children !
2. Read, understand and follow your power tool manufacturer’s instructions for safety. Always wear safety glasses or eye shields before commencing power tool operation. Always keep hands, face, hair, loose clothing, and body ata safe distance from spindles and cutting tools. Always keep a firm grip on tool handles when in operation. Always disconnect from the power source before adjusting power tools.

MODEL AND PARAMETERS

STRUCTURE DIAGRAM AND COMPONENTS

OPERATION

A: KNOB ON DRAWER FRONT(Center of width and height)

1. Measure the width and height of the drawer .

2. Set Large Stop at half of the drawer height, and set the sliding end stop at half of the drawer width. Finally,drill holes .
   Note: ( Using a center punch for positioning is more convenient .)

3. Install the handle, and you’re done .

B: HANDLE ON DRAWER FRONT(Center of width and height)

1. :Measure hole centers of handles,adjust and tighten Sliding Drill Guides .
   (Cover unused bushing with tape)

2. :Measure the width and height of the drawer .

3. :Set Large Stop at half of the drawer height, and set the sliding end stop at half of the drawer width. Finally,drill holes .
   Note: ( Using center punch for positioning is more convenient .)

4. :Install the handle, and you’re done .

C: KNOB ON DOOR INSTALLATION (Off center of width and height)

1. :Place the knob to find a position you like and mark it .

2. :Measure from the top of the door to mark and set Sliding End Stop to the measurement .

3. :Measure from the side of the door to mark and set Large Stop to the measurement .

4. :Place the tool as a picture and drill a hole through the drill bushing
   Note: ( Using a center punch for positioning is more convenient .)

5. :The flipping tool punches a hole in the other cabinet door .

6. : Install the handle, and you’re done .

D:HANDLE ON DOOR INSTALLATION(Off center of width and height)

1. :Place the handle to find a position you like and mark the bottom hole location .

2. :Measure from the top of the door to mark and set Sliding End Stop to the measurement .

3. :Measure from side of door to mark and set Large Stop to the measurement .

4. :Place the tool as a picture and drill a hole through the drill bushing
   (NOTE: Using a center punch for positioning is more convenient .)

5. :The flipping tool punches a hole in the other cabinet door.

6. : Install the handle, and you’re done .

MAINTENANCE

1. After each use, please install it in time and keep it properly to avoid losing parts .
2. Clean the surface after each use .

Address: Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
EC REP: SHUNSHUN GmbH. Romeracker 9 Z2021,76351
Linkenheim-Hochstetten, Germany
UK REP: Pooledas Group Ltd. Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place,
Rancho Cucamonga, CA 91730
Made In China

TechnicalSupport and E-Warranty Certificate
www.vevor.com/support

References

• Contact Us – Official VEVOR Support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>