nVent MCSS Modular Single Door Instruction Manual

June 17, 2024
nVent

nVent logo

Floor standing enclosures
Combinable version Stainless steel
MOUNTING INSTRUCTIONS
6885-0120-02 REV.15

MCSS Modular Single Door

nVent MCSS Modular Single DoornVent MCSS
Modular Single Door - Figure 1nVent
MCSS Modular Single Door - Figure 2

WARNING: When mounting on or over a combustible surface, a floor plate of at least 1.43 mm galvanized or 1.6 mm uncoated steel extended at least 150 mm beyond the equipment on all sides must be installed.
WARNING: In order to maintain the environmental integrity of the enclosure, devices with the same environmental ratings shall be used to close openings in customized enclosure.

MCSS

nVent MCSS Modular Single Door - Figure 3

MCDSnVent MCSS Modular Single Door - Figure 4

COMBINABLE ENCLOSURE

nVent MCSS Modular Single Door - Figure 5nVent
MCSS Modular Single Door - Figure 6

MOUNTING THE LIFT HANDLE

nVent MCSS Modular Single Door - Figure 7

http://www.eldon.com/en/Landing/QR-Swinghandle

nVent MCSS Modular Single Door - Figure 8http://www.eldon.com/en/Landing/QR-FS-180-Hinges

Standard Locking System Lift Handle Locking System
![nVent MCSS Modular Single Door - Lift Handle Locking](https://manuals.plus

/wp-content/uploads/2024/02/nVent-MCSS-Modular-Single-Door-Lift-Handle- Locking.jpg)

nVent MCSS Modular Single Door - Lift Handle Locking 2

MOUNTING LSEL

nVent MCSS Modular Single Door - Figure 9nVent
MCSS Modular Single Door - Figure 10

MCSS REAR PANEL

nVent MCSS Modular Single Door - Figure 11

MCDS REAR PANELnVent MCSS Modular Single Door - Figure
12

BOTTOM PLATE

nVent MCSS Modular Single Door - Figure 13

MOUNTING PLATE

nVent MCSS Modular Single Door - Figure 14http://www.eldon.com/en/Landing/QR-Mounting-plate-assembly

nVent MCSS Modular Single Door - Figure 15

http://www.eldon.com/en/Landing/QR-Mounting-plate-adjustment-in-depth

SPMS

nVent MCSS Modular Single Door - Figure 16

  • – Used only on enclosures 800 mm deep and above.
    Retainer mounting

nVent MCSS Modular Single Door - Figure 17

NOTE: Retainers are delivered pre-assembled.

SPMS

For the old design frame (800 mm in depth or more), the following additional steps are required:

nVent MCSS Modular Single Door - old design framenVent MCSS Modular Single Door - Figure 18

http://www.eldon.com/en/Landing/QR-External-baying-brackets-assembly

nVent MCSS Modular Single Door - Figure 19

http://www.eldon.com/en/Landing/QR-Lifting-possibilities-and-assembly

nVent MCSS Modular Single Door - Figure 20

Note: It is mandatory for all four brackets to be installed at all four corners!

  • The fixation holes can be used to better fix the bracket to the frame,using cage nuts and screws!

nVent MCSS Modular Single Door - Figure 21http://www.eldon.com/en/Landing/QR-Filler-mounting-plate- assembly

nVent MCSS Modular Single Door - Figure 22

http://www.eldon.com/en/Landing/QR-Change-door-opening-for-standard-FS- enclosures

DHN 180
Door adjustment

nVent MCSS Modular Single Door - Figure 23http://www.eldon.com/en/Landing/QR-FS-180-Hinges

nVent MCSS Modular Single Door - Figure 24

http://www.eldon.com/en/Landing/QR-Earthing-FS-enclosures-Mounting-plate- ECFA

nVent MCSS Modular Single Door - Figure 25nVent
MCSS Modular Single Door - Figure 26

nVent logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals