LITETRONICS FLASFM3 Flood Light Slipfitter Mount Instruction Manual
- June 17, 2024
- Litetronics
Table of Contents
LITETRONICS FLASFM3 Flood Light Slipfitter Mount
Product Information
Specifications
- Product: Slipfitter Mount for Flood Lights
- Models: 255W (FLASFM3), 330W (FLABSFM3)
- Mount Type: Slipfitter Bracket Mount
- Required Tools: Allen Wrench / Hex Key
FAQ
- What comes in the box?
- The box includes Slipfitter Allen Head Bolts (M8 x25) (x4), Spring Washer M8 (x4), Flat Washer M8 (x4), Ground Washer M8 (x1), and Installation Instructions.
- How can I contact customer service?
- You can reach customer service at CustomerService@Litetronics.com or call 1-800-860-3392.
Product Usage Instructions
Installation
- Before Installation, carefully remove all parts from the packaging and inspect for defects.
- Turn off the power supply from the main circuit breaker.
Slipfitter Bracket Mount Installation
- Separate the base and mount by removing the M8 screw.
- Run the input wire through the base, affix the base to the fixture with screws, and lock it in place.
- Pass the wires through the mount, install the mount, and keep the M8 screw loose.
Slipfitter Mount Installation
- Complete the wire connection according to the area light or flood light installation instructions.
- Align the fixture to the required angle and tighten the M8 screw after confirming the angle.
- Turn the power back on.
Safety Instructions and Warnings
- Always follow safety precautions when installing electrical components.
- If in doubt, consult a professional electrician.
SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS AND WARNINGS
- When using electrical equipment, basic safety precautions should always be observed
- This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved
- Installation should only be conducted by a qualified electrician in accordance with NEC and any relevant local building codes.
- Be certain electrical power is OFF before and during installation and maintenance.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or sharp objects.
WHAT COMES IN THE BOX
- Slipfitter
- Allen Head Bolts (M8 x25) (x4)
- Spring Washer M8 (x4)
- Flat Washer M8 (x4)
- Ground Washer M8 (x1)
- Installation Instructions
REQUIRED TOOLS
- Allen Wrench / Hex Key
INSTALLATION INSTRUCTIONS
INSTRUCTIONS
- Before Installation, carefully remove all parts from the packaging. Inspect product for defects due to shipping.
- Always turn off the power supply from main circuit breaker first!
SLIPFITTER BRACKET MOUNT INSTALLATION
- Separate base and mount by removing M8 screw. (Figure 1)
- Run the input wire through the base (watch out not to scratch the wire). Affix the base with screws and lock to the fixture. (Figure 2)
- Pass the wires through the mount (watch out not to scratch the wire). Install the mount and keep M8 screw loose. (Figure 3)
SLIPFITER MOUNT INSTALLATION
- Finish the wire connection accordingly (refer to area light or flood light installation instructions for wiring diagram).
- Align the fixture to required angle. Tighten M8 screw after angle is confirmed. (Figure 4)
- Turn power back on.
Note: Adjustable angle is 0~+/-90 °. (Figure 4)
Contact
Thank you for choosing LITETRONICS®
- 6969 W. 73rd Street
- Bedford Park, IL 60638
- WWW.LITETRONICS.COM
- CustomerService@Litetronics.com
- 1-800-860-3392
The information and product specifications contained in these instructions are based upon data believed to be accurate at the time of printing. This information is subject to change without notice and without incurring liability. If you have questions regarding specific product details, please contact us at 800-860-3392 or via email at customerservice@litetronics.com. To check for an updated version of these instructions, please visit www.litetronics.com.