Olarm PRO IDS X-Series Adapter Instruction Manual
- June 3, 2024
- Olarm PRO
Table of Contents
Olarm PRO IDS X-Series Adapter
Locate your alarm panel
Note that the alarm panel is not the keypad. Alarm panels are typically
installed in a hidden location in the home such as a cupboard or
basement. Verify the
alarm panel’s firmware version
Olarm PRO only supports IDS X-Series alarm panels with firmware with version
2.5 and up. An alarm installer should be able to upgrade the alarm panel
firmware if required. See the end of this manual for tips on how to view the
alarm panel firmware version via the keypad.
Unbox your Olarm PRO
The Olarm PRO box includes the following:
- 1x Olarm PRO device
- 1x Connector cable
- 1x Drill hole template and LED colour legend
- 2x Screws and wall plugs
- 1x External antenna (selected Olarm PRO models only)
Download the Olarm mobile app and register your device
Scan QR code, or navigate to your App Store on your device and search for
“Olarm”.
Power down
the alarm panel
Turn the power to your IDS X-Series alarm panel off at the mains and
disconnect the battery.
Connect the serial cable
Connect the 4-pin side of the supplied cable to the Universal port on the
Olarm PRO. Connect the 5-pin side of the supplied cable to an Olarm PRO IDS
X-Series adapter board. These adapter boards are sold seperately to the Olarm
PRO and can be purchased directly from Olarm. Please contact
sales@olarm.co should you want to order. Connect to
the X-Series adaptor board to the alarm panel
Connect the Olarm IDS X-Series adapter board to the IDS X-Series Alarm panel
as indicated below. Wire the red 12V wire from the Olarm IDS X-Series adapter
board into one of the AUX+ terminals on the alarm panel as illustrated
below. Turn the
alarm panel back on
Power your IDS X-Series alarm panel on again. The Olarm PRO should light up as
per the chart below.
Check your Olarm PRO’s status
Colour
Status
Configure the alarm panel
This section will guide you through entering a series of codes / settings to allow the Alarm Panel and Olarm PRO to communicate. The IDS X-Series alarm system caters for a range of keypads and they all work slightly different. Please follow the instructions relating to your keypad.
- Ensure that the alarm system is powered up and on.
- Ensure the alarm is disarmed.
- Press # to clear the keypad.
- Enter the installer menu by typing the installer code followed by a *.
- a. The default installer code is 9999 or 999999.
- b. If these do not work, please contact the alarm installer who installed / manages the alarm system.
- From the installer menu, enter the code 196 followed by *.
- Enter the serial security code 123456 followed by *.
- Press # button 2 to 3 times until you hear 4 to 5 beeps from the keypad, this will take you out of the installer menu.
- The keypad will then display:
- The Olarm PRO should turn a solid blue colour within 2 minutes.
Mount the Olarm PRO
Mount your device using the screws and drill template provided.
We suggest mounting the Olarm PRO device on a wall or on the outside of the
alarm panel. Please do NOT mount the Olarm PRO inside the alarm box or near
any other radio equipment as it will reduce the signal strength and result in
your device not functioning correctly.
Troubleshooting
- If your device LED remains flashing Green for more than 3 minutes – Please check the connection between the Olarm PRO and the alarm panel.
- If your device LED is Red – Please check the connection between the Olarm PRO and the alarm panel.
- If your device LED is Orange – Please ensure that the Olarm PRO is located in an area with good Vodacom and/or MTN signal strength.
- If it is not, please ensure that your device is connected to Wifi using the wizard inside the Olarm app.
- If your device LED is not coming on – Please check the connection between the Olarm PRO and the alarm panel and that the alarm panel is connected to power.
- If your device LED remains purple for more than 15 minutes – Please contact Olarm Support.
To check your alarm panel firmware version
Hold down the * key on the keypad down for 3 seconds. You should see the
following display.
- Do NOT enter the Master Code at this stage, instead press * which will then display the firmware version.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>