PROSAUNAS 128151 Universal Sauna Light Kit 16-Ft Flexible LED Strip User Guide
- September 18, 2024
- PROSAUNAS
Table of Contents
PROSAUNAS 128151 Universal Sauna Light Kit 16-Ft Flexible LED Strip
Specifications
- Operating Voltage: 120VAC
- Flexible LED Neon Length: 16FT
- Operating Voltage Wattage (VDC): 24V DC 48W
- Lumens: 1,584
- Kelvin Temperature: N/A
- Operating Temperature: N/A
- IP Rating: IP67
- Certification: ETL / SGS
Product Usage Instructions
LED Handling
Handle LED light with care! Follow the guidelines below:
- Horizontal Bending: Follow the maximum bend radius of 2
- Channel/Clip Mount: Use appropriate clips for mounting
- Twisting: Avoid twisting the LED light
- Vertical Bending: Handle with care
- Cutting Flexible LED Neon: Cut on marked lines only
Installation Steps
Step 1. Identify LED Install Location
Identify the location where the LED light will be installed.
Step 2. LED Mounting Clips
Mount the LED using the provided clips ensuring it does not exceed the maximum operating temperature.
Step 3. Power Supply Connection
Determine how the power supply will be connected, either through a standard 120VAC receptacle or wired into your Sauna equipment power module.
FAQs
- Q: Can I cut the Flexible LED Neon to a custom length?
- A: Yes, you can cut the Flexible LED Neon on the marked lines only.
- Q: What is the IP rating of the product?
- A: The product has an IP rating of IP67, indicating it is dust-tight and can withstand immersion in water up to 1 meter depth for 30 minutes.
SAFETY & WARNINGS
PLEASE READ THIS MANUAL IN ITS ENTIRETY PRIOR TO INSTALLATION!
- Qualified Personnel Only: Installation of this system must be performed by a certified electrician, following all national electric code and local building code requirements.
- Equipment Protection: The power supply must be installed in a location that is completely protect-ed from moisture, rain, and inclement weather.
- Temperature Considerations: Please refer to the specifications on page 4 to determine the maxi-mum temperature rating of each component. Do not install any components in areas that exceed their maximum temperature limits, as this will lead to product failure and void the warranty.
- Heater Clearance: Maintain a safe distance between your Flexible LED light and the sauna heater. Avoid directly installing the lights above the heater or within 20 inches of its sides.
- Light Placement: Carefully consider the placement of your LED lights to avoid shining directly into eyes. A diffused or indirect lighting approach is recommended.
- Handling Precautions:
- Uncoil Before Powering: Do not connect power to the LED light while it is still attached to the spool or coiled up. Unwind the light completely before powering it on.
- Avoid Damage: Refrain from folding or twisting the LED light, as this can cause physical damage to the LEDs and lead to malfunctions, refer to page 5 for LED Handling
Electrical Requirements
Always disconnect power from the system at the circuit breaker before performing any electrical installation or maintenance
- Power Source: The lighting system requires a 120VAC power source.
- Qualified Electrician: A certified electrician should determine the appro-priate electrical outlet type, box configuration, and necessary wiring to ensure compatibility and safety.
- Electrical Safety: Utilizing improper voltage or making incorrect electrical connections can damage system components and void the warranty
PACKAGE CONTENTS
SPECIFICATIONS
Flexible LED Neon
Length
| Operating Voltage (VDC)| ****
Wattage
| ****
Lumens
| ****
Kelvin Temperature
| ****
Operating Temperature
| ****
IP Rating
| ****
Certification
16FT
| ****
24V DC
| ****
48W
| ****
1,584
| ****
3500K
| ****
-13°F to 200°F
| ****
IP67
| ****
ETL / SGS
Power Supply
Input Voltage
| ****
Output Voltage
| ****
Rated Power
| ****
AC
Current
| ****
DC
Current
| ****
Operating Temperature
| ****
IP Rating
| ****
Certification
120 VAC
| ****
24V DC
| ****
90W
| ****
1.3A
| ****
3.75A
| ****
-22°F to 158°F
| ****
IP20
| ****
UL / CE / FCC
LED HANDLING
HANDLE LED LIGHT WITH CARE
Cutting Flexible LED Neon
-
Determine the length of LED needed for the installation location
-
Using sharp cutters or scissors cut at closest cut point to the length needed, see diagram below.
Note: Cut only on marked lines. -
After cutting to length apply silicone to cut end and install end cap.
INSTALLATION
STEP 1. Identify LED Install Location
Identify location where LED light will be installed.
Common installation spots are,
- Backrest shining up or down
- Under bench
- Sauna Floor
- Exterior Sauna
STEP 2. LED Mounting Clips
- Grab Mounting Clips and screws. Clips are provided with 1 screw each.
- If using your own screw you will need a minimum size #4 x 5/8” screw to mount clips.
- It is recommended that clips be mounted every 8”to 12” to support LED light.
- Take LED and gently press light into each clip.
- Follow connection diagram on page 4 for LED wire connections.
Note: Images below show examples of clip installation. To remove LED from clip gently pull up on LED at each clip to release, avoid bending LED as this will damage the light.
Important:
- LED Light should not be installed above or within 20” of sauna heater.
- “Always check temperature at install location of LED light and ensure it does not exceed maximum operating temp.”
Note: It is recommended to run sauna without LED light installed and check temperature at intended install location to get an accurate temperature.
STEP 3. Power Supply Connection
Determine how power supply will be powered, this can be from a standard 120VAC receptacle or wired into your Sauna equipment power module, see images below for wiring.
Important
Images below are shown as a reference. It is important to verify heater manufacturers’ installation steps for connecting lighting.
120VAC Receptacle
(wired to on/off switch)
Huum
Main Module
Technical Support
- ( 224)253 -5909
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>