CHAMPION POWER EQUIPMENT 201161 Tri-Fuel Generator with CO Shield User Guide

CHAMPION POWER EQUIPMENT 201161 Tri-Fuel Generator with CO Shield

Specifications

• Model: 12,000W Triple Fuel Generator
• Power Output: 12,000 Watts
• Fuel Types: Gasoline, Propane (LPG), Natural Gas (NG)
• Oil Type: 5W-30, 37.2 fl. oz. (1100ml)

Product Usage Instructions

Setup

1. Attach wheel kit:
   • Do not remove the generator from the pallet until the wheels are fully installed.
2. Remove generator from the pallet:
   • Remove the wooden block from behind the support leg.
   • Slide the unit forward until the wheels touch the ground.
   • Raise the handle to pull the unit out from the wood pallet.
3. Connect the battery:
   • Cut cable tie on each side of the battery connector.
   • Push two halves of the battery connector together tightly.
4. Add oil:
   • Recommended oil: 5W-30, up to 37.2 fl. oz. (1100ml). Do not overfill.
5. Add fuel:
   • Add Gasoline, Propane (LPG), or Natural Gas (NG) as fuel options.

Starting the Engine Gasoline

1. Turn the fuel select dial to the GASOLINE ON position.
2. Pull the choke knob to the CHOKE position.
3. Press and hold the ignition switch to the START position.
4. Push the choke knob into the RUN position.

Propane (LPG) and Natural Gas

1. Open the propane tank or natural gas valve.
2. Turn the fuel select dial to PROPANE ON or NATURAL GAS ON position.
3. Pull the choke knob to the CHOKE position.
4. Press and hold the ignition switch to the START position for 2-3 seconds.
5. Push the choke knob into the RUN position.

Important Safety Reminders

• Only use outside and far away from windows, doors, and vents.
• Do not use E15 or E85 gasoline for operation.
• Never start or stop the generator with electrical devices connected or turned on.

Frequently Asked Questions (FAQ):

Q: Can I use this generator indoors?

• A: No, using a generator indoors can be fatal due to carbon monoxide exposure.
• Always operate the generator outdoors and away from any enclosed spaces.

Q: What type of oil should I use for this generator?

• A: It is recommended to use 5W-30 oil, up to 37.2 fl. oz. (1100 ml) for this generator.
• Avoid overfilling the oil tank.

Q: How do I start the generator using propane or natural gas?

• A: To start the engine using propane or natural gas, ensure the respective fuel source is connected and follow the specific steps outlined in the user manual for your safety and proper operation.

PARTS INCLUDED

DANGER

MOVE GENERATOR OUTDOORS.

• Using a generator indoors CAN KILL YOU IN MINUTES. Generator exhaust contains carbon monoxide.
• This is a poison you cannot see or smell.
• NEVER use inside a home or garage, EVEN IF doors and windows are open.
• ONLY use OUTSIDE and far away from windows, doors, and vents.

WARNING

• Read the ENTIRE operator’s manual to become familiar with the features of this product before operation.
• This QuickStart Guide IS NOT a substitute for the Operator’s Manual.
• Failure to operate the product correctly could result in damage to the product, or personal property or cause serious injury or death.

NOTICE

• Keep all objects at least 5 feet (1.5 m) from the generator. Heat from the muffler and exhaust gas can ignite combustible materials.

SET UP

1. Attach wheel kit. Assembly > Install the Wheel Kit
   • DO NOT REMOVE the generator from the pallet until the wheels have been fully installed.
2. Remove generator from the pallet. Assembly > Install the Wheel Kit
3. Remove the wooden block from behind the support leg.
4. Slide the unit forward until the wheels touch the ground.
5. Then raise the handle to pull the unit out from the wood pallet.
6. Connect the battery. Assembly > Connect the Battery
   • Cut cable tie on each side of the battery connector.
   • Push two halves of the battery connector together tightly.

STARTUP

• Add oil. Assembly > Add Engine Oil.
• Recommended: 5W-30, up to 37.2 fl. oz. (1100 ml). DO NOT overfill.
• Move the generator outdoors.
• ONLY USE OUTSIDE AND FAR AWAY FROM WINDOWS, DOORS, AND VENTS.
• Add fuel – Gasoline or Propane (LPG), or Natural Gas (NG) Assembly > Add Fuel
• FOR GASOLINE OPERATION: DO NOT USE E15 OR E85
• DO NOT plug in any electrical devices.
• Starting the Engine: Gasoline

1. Turn the fuel select dial to the “GASOLINE ON” position
2. Pull the choke knob to the “CHOKE” position.
3. Press and hold the ignition switch to the “START” position.
4. Push the choke knob into the “RUN” position.

Starting the Engine: Propane (LPG) and Natural Gas

1. Open the propane tank or natural gas valve.
2. Turn the fuel select dial to the “PROPANE ON” or “NATURAL GAS ON” position.
3.  Pull the choke knob to the “CHOKE” position.
4. Press and hold the ignition switch to the “START” position for 2-3 seconds.
5. Push the choke knob into the “RUN” position.
6. Press and hold the ignition switch to the “START” position.
   • If the engine does not start, wait 10 seconds, then repeat step 6.

Plug in. Operation > Connecting Electrical Loads.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>