Hikvision HM-TP30-1AQF-ECO-V Handheld Thermal Camera User Guide
- June 17, 2024
- Hikvision
Table of Contents
Hikvision HM-TP30-1AQF-ECO-V Handheld Thermal Camera
Product appearance is for reference only and may differ from the actual product.
Brief Description
The handheld thermal camera is a camera with thermal images. The built-in high-sensitivity IR detector and high-performance sensor detect the temperature changes and measure the real-time temperature. You can download HIKMICRO Analyzer https://www.hikmicrotech.com/en/industrial-products /hikmicro-analyzersoftware.html to analyze pictures offline professionally and generate a custom format report on your PC.
Components & Buttons (Page 1)
Components
Note : Optical lens is only supported by certain models. Please refer to the
actual product.
Buttons
Charge Device
- Check the OSD (on-screen display) information for the battery status.
- When the battery is low, charge the device and ensure it works properly.
- Charge the device for more than 3 hours before first use.
Steps
- Lift the type-C interface cover.
- Connect the device to the power supply using the type-C cable to charge the device.
- User Manual
Regulatory Compliance and Safety
Information
Read all information and instructions in this document carefully before using
the device and keep it for further reference. For more device information and
instructions, please visit our website at
www.hikmicrotech.com. You can also refer to
other documents (if any) accompanying the device or scan the QR code (if any)
on the packaging to get more information. © 2023 Hangzhou Microimage Software
Co., Ltd. All rights reserved.
About this Manual
The Manual includes instructions for using and managing the Product. Pictures,
charts, images and all other information hereinafter are for description and
explanation only. The information contained in the Manual is subject to
change, without notice, due to firmware updates or other reasons. Please find
the latest version of this Manual on the HIKMICRO website
(www.hikmicrotech.com). Please use this Manual
with the guidance and the assistance of professionals trained in supporting
the Product.
Trademarks
and other HIKMICRO trademarks and logos are the properties of HIKMICRO in
various jurisdictions. Other trademarks and logos mentioned are the properties
of their respective owners.
DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT
DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND
“WITH ALL FAULTS AND ERRORS”. HIKMICRO MAKES NO WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY,
OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR
OWN RISK. IN NO EVENT WILL HIKMICRO BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA,
CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF
CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE.
IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKMICRO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKMICRO SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKMICRO WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION.
THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY
ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR
FUEL CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATTER PREVAILS.
These clauses apply only to the products bearing the corresponding mark or
information. EU/UK Compliance Statement This product and – if applicable – the
supplied accessories too are marked with “CE” and comply therefore with the
applicable harmonized European standards listed under the Directive 2014/30/EU
(EMCD) and Directive 2011/65/EU (RoHS).
Note: The products with an input voltage of within 50 to 1000 VAC or 75
to 1500 VDC comply with Directive 2014/35/EU (LVD), and the rest products
comply with Directive 2001/95/EC (GPSD). Please check the specific power
supply information for reference.
This product and – if applicable – the supplied accessories too are marked
with “UKCA” and comply therefore with the following directives:
Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety)
Regulations 2016, the Restriction of the Use
of Certain Hazardous Substances in Electrical and Electronic Equipment
Regulations 2012. For the device without a supplied battery, use the battery
provided by a qualified manufacturer. Refer to the product specification for
detailed battery requirements For the device without a supplied power adapter,
use the power adapter provided by a qualified manufacturer. Refer to the
product specification for detailed power requirements.
Directive 2012/19/EU (WEEE Directive)
Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the European Union. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or dispose of it
at designated collection points. For more information see
www.recyclethis.info.
According to the Waste Electrical and Electronic Equipment Regulations 2013:
Products marked with this symbol cannot be disposed of as unsorted municipal
waste in the United Kingdom. For proper recycling, return this product to your
local supplier upon the purchase of equivalent new equipment, or dispose of it
at designated collection points. For more information see:
www.recyclethis.info. Directive 2006/66/EC and
its amendment 2013/56/EU (Battery Directive): This product contains a battery
that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information.
The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or a designated collection point. For more information see: www.recyclethis.info. According to the Batteries and Accumulators (Placing on the Market) Regulations 2008 and the Waste Batteries and Accumulators Regulations 2009: This product contains a battery that cannot be disposed of as unsorted municipal waste in the United Kingdom. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or a designated collection point. For more information see: www.recyclethis.info. Industry Canada ICES-003 Compliance This device meets the CAN ICES-003 (B)/NMB-003 (B) standards requirements.
Safety Instruction
These instructions are intended to ensure that the user can use the product
correctly to avoid danger or property loss.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical
safety regulations.
Transportation
- Keep the device in original or similar packaging while transporting it.
- Keep all wrappers after unpacking them for future use. In case of any failure occurred you need to return the device to the factory with the original wrapper.
- Transportation without the original wrapper may result in damage to the device and the company shall not take any responsibility.
- Do not drop the product or subject it to physical shock. Keep the device away from magnetic interference.
Power Supply
- The input voltage should meet the Limited Power Source (5 VDC, 2 A) according to the IEC61010-1 standard. Please refer to the technical specifications for detailed information.
- Make sure the plug is properly connected to the power socket.
- DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload.
Battery
- The built-in battery cannot be dismantled. Please contact the manufacturer for repair if necessary. The battery may explode if it is replaced by an incorrect type.
- Replace with the same or equivalent type only.
- Dispose of used batteries in conformance with the instructions provided by the battery manufacturer.
- For long-term storage of the battery, make sure it is fully charged every half year to ensure the battery quality. Otherwise, damage may occur.
- Make sure the plug is properly connected to the power socket.
- When the device is powered off and the battery is full, the time settings can be kept for 60 days.
- The standard adapter power supply is 5 V.
- The battery is certified by UL2054.
Maintenance
- If the product does not work properly, please contact your dealer or the nearest service centre. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
- Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary.
- If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired.
- We recommend you send the device back for calibration once a year, and please contact the local dealer for information on maintenance points.
- Your camera will periodically perform a self-calibration to optimize image quality and measurement accuracy. In this process, the image will pause briefly and you’ll hear a “click” as a shutter moves in front of the detector.
- The self-calibration will be more frequent during start-up or in very cold or hot environments. This is a normal part of operation to ensure optimum performance for your camera.
Calibration Service
We recommend you send the device back for calibration once a year, and please
contact the local dealer for information on maintenance points. For more
detailed calibration services, please visit
https://www.hikmicrotech.com/en/support
Using Environment
- Make sure the running environment meets the requirements of the device. The operating temperature shall be -10 °C to 50 °C (14 °F to 122 °F), and humidity shall be 95% or less.
- Place the device in a dry and well-ventilated environment.
- DO NOT expose the device to high electromagnetic radiation or dusty environments.
- DO NOT aim the lens at the sun or any other bright light.
- When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.
- The device is suitable for indoor and outdoor uses, but do not expose it in wet conditions.
- The level of protection is IP 54.
- The pollution degree is 2.
Technical support
- The https://www.hikmicrotech.com/en/contact-us.html portal will help you as a HIKMICRO customer to get the most out of your HIKMICRO products.
- The portal gives you access to our support team, software and documentation, service contacts, etc.
Emergency
- If smoke, odour, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service centre.
- Laser Light Supplement Warning
- Warning: The laser radiation emitted from the device can cause eye injuries, burning of skin or inflammable substances.
- Prevent eyes from the direct laser.
- Before enabling the Light Supplement function, make sure no human or inflammable substances are in front of the laser lens. The wavelength is 650 nm, and the power is less than 1 mW. The laser meets the IEC60825-1:2014 standard.
- Laser maintenance: It is not necessary to maintain the laser regularly. If the laser does not work, the laser assembly needs to be replaced in the factory under warranty.
- Keep the device powered off when replacing the laser assembly. Caution-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road,
Xixing Subdistrict, Binjiang District, Hangzhou,
Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products might be subject to export
controls in various countries or regions, including without limitation, the
United States, European Union, United Kingdom and/or other member countries of
the Wassenaar Arrangement. Please consult your professional legal or
compliance expert or local government authorities for any necessary export
license requirements if you intend to transfer, export, or re-export the
thermal series products between different countries.
Facebook: HIKMICRO Thermography LinkedIn: HIKMICRO
Instagram: hikmicro_thermography YouTube: HIKMICRO Thermography
E-mail: support@hikmicrotech.com Website:
www.hikmicrotech.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>