HARVIA CX1104XW01 Spirit 6kW and 9kW + WiFi App control User Manual

HARVIA CX1104XW01 Spirit 6kW and 9kW + WiFi App control

Product Information

Specifications

• Model : Harvia Xenio CX1104XW01
• Delivery Contents :
  • Control unit
  • Door switch sensor set
  • Temperature sensor + cable
  • Control panel + data cable
  • Mounting screws
  • Instructions for Installation and Use
• Max. Power : 6 kW
• Lighting : Max. 100 W

Product Usage Instructions:

Installation:

Follow the provided installation images for proper setup. Ensure proper distances are maintained during installation in a sauna facility.

Components:

The control unit includes a control panel, data cable, power unit, remote switch, door switch, temperature sensor, safety switch, heater/combi-heater, heater and steamer, main switch, WLAN router, and mobile device compatibility.

Operation:

Use the control panel to adjust settings and monitor the sauna environment. Ensure all connections are secure and sensors are properly placed for accurate readings.

FAQ

• Q: What is included in the delivery contents?
  • A : The delivery includes the control unit, door switch sensor set, temperature sensor with cable, control panel with data cable, mounting screws, and instructions for installation and use.
• Q: What is the maximum power of the Harvia Xenio CX1104XW01?
  • A : The maximum power of the Harvia Xenio CX1104XW01 is 6 kW.

System components

1. Control panel
2. Data cable
3. Power unit
4. Remote switch*
5. Door switch
6. Temperature sensor
7. Safety switch *
8. Heater / Combi-heater
9. Heater and steamer
10. Main switch
11. WLAN router
12. Mobile device + MyHarvia

INSTALLATION IMAGES

Electrical Connections

• E. Control panel
• F. Remote switch
• G. Safety switch
• H. Temperature sensor
• I. Lighting (max 100 W)
• J. Control of electric heating
• K. Residual current device

Distances for installation in a sauna facility

Installation of the Sensor

Mounting the door sensor

Maximum detection distance of the sensor from the magnet

Resetting the Overheat Protector

INSTRUCTIONS FOR INSTALLATION

See WARNINGS AND NOTES

See INSTALLATION IMAGES

Technical data

Installing the Power Unit › Image 1

Install the power unit in a dry area or sauna room (ambient temperature >0ºC). Note! Do not embed the power unit into the wall, since this may cause excessive heating of the internal components of the unit and lead to damage.

Electrical Connections › Image 2

Connect the wiring according to Figure 2. Tables show the wire and fuse sizes, depending on the heater output. For more detailed installation instructions see the instructions for installation and use of the selected heater model. The maximum load from the control unit to the heater is 9 kW.
Power Unit Fuse Faults

Replace a blown fuse by a new one with the same value. The location of the fuses in the power unit is shown in Figure 2.

• If the fuse for the electronic card has blown, there is likely a fault in the power unit. Service is required.
• If the lighting fuse (Figure 2) is broken, there is a fault in the lighting. Check the operation and wiring of the lighting.

Terminals for controlling electrical heating

The power unit interface J (Figure 2) can also be used for purposes such as electric heating control. When the heater is turned on from the control unit, voltage is generated in terminal J. The heating can be switched on or off based on the signal.

Installation of the Sensor › Image 4

NOTE! Always check the correct location of the temperature sensor from the heater’s installation instructions.

• See image 4A
• Note! Do not install the temperature sensor closer than 1000 mm to an omnidirectional air vent or closer than 500 mm to an air vent directed away from the sensor. See Figure 4B. The airflow near an air vent cools down the sensor, which gives inaccurate temperature readings to the control unit. As a result, the heater might overheat.

Mounting the door sensor › Image 5

Installation of a sensor on a door frame:

• Attach the sensor holder to the door frame, using either a screw (Figure 5A) or double-sided tape (Figure 5B).
• Install the sensor in the holder (Figure 5C).
• Note : If the door frame is sheet metal and there is room for the sensor behind it, the sensor can also be attached using a grommet (Figure 5D). An 8 mm drill bit should be used.

Attaching the magnet to the door:

• Fix the magnet holder to the door, using either a screw (Figure 5E) or double-sided tape (Figure 5F).
• Press the magnet into place in the holder (Figure 5G).
• The magnet can also be mounted on the door using only double-sided tape (Figure 5H).

Resetting the Overheat Protector › Image 6

The sensor box (WX232) contains a temperature sensor and an overheat protector. If the temperature in the sensor’s environment rises too high, the overheat protector cuts off the heater’s power. Resetting the overheat protector is shown in figure 6.

Note! The reason for the going off must be determined before the button is pressed.

WARNINGS AND NOTES

READ THE WARNINGS AND MANUAL CAREFULLY BEFORE USING THE PRODUCT!

This user manual is intended for the owner or the person in charge of the product, as well as for the electrician in charge of the electrical installation of the product. After completing the installation, the person in charge of the installation should give these instructions to the owner of the product or to the person in charge of its operation. Please read more instructions for installation, use and recycling from www.harvia.com. (Original user manual from manufacturer).

INSTALLATION AND MAINTENANCE

• The sauna heater is designed for the heating of a sauna room to bathing temperature. It is not to be used for any other purpose!
• The control unit is meant to control the functions of a sauna and a sauna heater. It is not to be used for any other purpose!
• Note! The control unit is not intended for use in community facilities or for professional use.
• The electrical device may only be connected to the electrical network in accordance with the current regulations by an authorized, professional electrician. After completing the installation, the person in charge of the installation should give these instructions to the owner of the sauna or to the person in charge of its operation.
• All maintenance that requires special skills must be performed by a trained professional.
• Always disconnect the device from the electricity network before carrying out any maintenance work!
• This device is allowed to be used by 8 years old or older children and persons with reduced physical, sensory or mental capabilities, or persons with lack of experience and knowledge if they are supervised or they have been instructed to use the device safely and if they are aware of the dangers involved. Children should not play with the device. Children should not clean or do operations to the device without supervision.
• Check the device for visible damage before installing and using the device. Do not use a damaged device.
• It is absolutely necessary to install the device according to the values stated in the instructions of installation and use. Neglecting them causes a risk of fire.
• If suitable accessories are installed in the device, follow the accessory-specific operating and installation instructions!
• Clean the product by using a lightly moistened cloth. Use only mild cleaning agents, never solvents or corrosive chemicals.
• This product should not be disposed of with general household waste. When recycling your product, take it to your local collection facility or contact the place of purchase.
• The device must be installed in such a way that the warning texts are easy to read after installation.
• The device must not be installed in a wall recess unless otherwise stated in the instructions.
• Do not place the supply air vent so that the airflow cools the temperature sensor (see temperature sensor installation instructions!)
• If the supply cord is damaged, it must be replaced by the manufacturer’s service person or a similarly qualified person in order to avoid a hazard.
• The use of a PVC-insulated cable as a connection cable for the heater is prohibited due to its thermal fragility.
• Do not connect the power supply to the electric heater via a residual current device.
• If the device is connected to the water supply, there must be a floor drain on the floor of the sauna room and/or washroom in case of hose breaks or leaks.

INSTRUCTIONS FOR USE AND BATHING

• Always check that there are no objects on the heater or near the heater before switching it on.
• Beware of hot heater. The stones and metal parts of the heater may burn the skin.
• Sea air and a humid climate may corrode the metal surfaces of the device.
• Do not hang clothes to dry in the sauna, as this may cause a risk of fire. Excessive moisture content may also cause damage to the electrical equipment.
• Do not press the overheating protection button before the cause of the fault has been found. Only persons authorized to carry out electrical installations can reset the overheat protector unless otherwise stated in the instructions manual.
• Always check that the heater has switched off and stopped heating after the on-time period has elapsed.
• The sauna room and surroundings of the heater must always be checked before the heater is switched on again or it is switched on with the remote-control system.
• The sauna room and surroundings of the heater must always be checked before the device is brought into standby mode required by remote control or pre-timed operation.
• According to the product standard IEC/EN 60335 -2-53 regulating electrical sauna heaters, the control unit can be used to remotely control the heater once the heater or sauna room door is equipped with a secure switch (safety or door switch).

Do not cover!

Spare parts

1. Control panel
2. Temperature sensor
3. Data cable 5 m
4. Circuit board (XT2020)

Guarantee

• The guarantee period for heaters, steam generators and control equipment used in saunas by families is two (2) years.
• The guarantee period for heaters, steam generators and control equipment used in saunas by building residents is one (1) year.
• The guarantee period for heaters, steam generators and control equipment used in commercial saunas facilities is three (3) months.
• The guarantee does not cover any faults resulting from failure to comply with installation, use or maintenance instructions.
• The guarantee does not cover any faults resulting from the use of stones not recommended by the heater manufacturer.

CONTACTS

• GLOBAL : P.O.Box 12

FINLAND

• +358 207 464 000
•  Teollisuustie 1-7
• 40951 Muurame
• harvia@harvia.fi
•  www.harvia.com

CENTRAL EUROPE

•  Sentiotec GmbH
• Division of Harvia Group
• Wartenburger Straße 31, A-4840
• T: +43 (0) 7672/22 900-  50  F -80
•  info@sentiotec.com
• www.sentiotec.com

References

• Harvia
• Harvia
• sentiotec

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>