ADATA 650 Kyber Gold Series Power Supply User Guide

: June 17, 2024
: ADATA

ADATA 650 Kyber Gold Series Power Supply

ADATA 650 Kyber Gold Series Power Supply

specification

Restricted substance and its chemical symbols)

exceeds the reference percentage value of presence condition. Indicates that the percentage content of the restricted substance does not exceed the percentage of

reference value of presence. Indicates that the restricted substance corresponds to the exemption

KYBER 650 GOLD SPECIFICATIONS

Model	KYBER850GOLD
AC Input	100-240VAC, 47-63Hz, 12A
DC Output	+5V
Output Current	20A
Output Wattage	100W
Total Continuous Power	650W

DC CABLE LISTING

Connector Type	Connector Quantity
Motherboard 20+4 Pin

1

ATX12V 8 / 4+4 Pin|

2

PCI-E 6+2 Pin|

2

SATA 5 Pin|

6

SATA 5 Pin|

2

KYBER 650 GOLD: EFFICIENCY

KYBER 650 GOLD: FAN CURVE

KYBER 750 GOLD SPECIFICATIONS

Model	KYBER850GOLD
AC Input	100-240VAC, 47-63Hz, 12A
DC Output	+5V
Output Current	20A
Output Wattage	100W
Total Continuous Power	750W

DC CABLE LISTING

Connector
Type| Connector
Quantity
---|---
Motherboard 20+4 Pin| 1
ATX 12V 8 / 4+4 Pin| 2
PCI-E 6+2 Pin| 2
SATA 5 Pin| -6
Molex 4 Pin| 2

KYBER 750 GOLD: EFFICIENCY

KYBER 750 GOLD: FAN CURVE

KYBER 750 GOLD SPECIFICATIONS

Model	KYBER750GOLD
AC Input	100-240VAC, 47-63Hz, 10A
DC Output	+5V
Output Current	20A
Output Wattage	100W
Total Continuous Power	750W

Connector
Type| Connector
Quantity
---|---
Motherboard 20+4 Pin| 1
ATX 12V 8 / 4+4 Pin| 2
PCI-E 12+4 Pin| 1
PCI-E 6+2 Pin| 2
SATA 5 Pin| 6
Molex 4 Pin| 2

KYBER 850 GOLD: EFFICIENCY

KYBER 850 GOLD: FAN CURVE

STAFETY AND AGENCY APPROVALS

INTERGRATED PROTECTION CIRCUITS

Over Voltage
Protection

Over Power
Protection

Shot Circuit
Protection

Over Current
Protection

Under Voltage
Protection

Over Temperature
Protection

No Load
Operation

Over Current
Protection

SAFETY AND PROTECTION

The main outputs will be latched off when each protection is triggered. The main output can be reset by cycling the DC remote on/off or AC power. +5Vsb output is auto recovery when fault condition is removed

KYBER GOLD SERIES

XPG KYBER GOLD Power Supply
AC Power Cord x 1
Thumb Screw x 4
User Manual

INSTALLING YOUR XPG KYBER GOLD POWER SUPPLY

Please turn off AC power switch if you are swapping the power supply.
Please install your XPG Power Supply in the correct area
Please use a screwdriver to install the power supply
Please connect the 18+10pin cable connector to the PSU socket
Please connect the 20+4 pin MB connector to the 24pin socket on the MB
Please connect the CPU 8pin cable connector to the PSU CPU power
Please connect the 8 or 4 pin CPU connector to the CPU power socket on the MB if required.
Please connect the PCI-E 8 Pin or 12VHPWR cable connector to the PSU PCI-E or 12VHPWR power socket if required.
Please connect the PCI-E 6+2 Pin or 12VHPWR connector to the Graphics Card connector if required.
Please connect the 6pin cable connector to the PSU SATA or Molex power socket if required.
Please connect the SATA or Molex Connectors to all the peripherals if required.
Please turn on the AC power switch if you have finished your system installation

TROUBLESHOOTING

If your system does not turn on after installing the power supply, please follow the troubleshooting guide listed below:
Please make sure the AC main power cord is connected to your PC correctly.
Please make sure the AC source is switched On
Please make sure the AC On/Off switch on the back panel of the power supply unit in the“I” (On) position.Please make sure the MB & CPU Power Socket & connectors are connected correctly on the Motherboard
If you still have problem turning on your PC, please contact ADATA Tech Support, ServiceCenter or your local dealer.

DURATION OF WARRANTY

ADATA Technology Co., Ltd. provides a 5 years warranty period for this product unless regional laws and regulations state otherwise.

LIMITATION OF WARRANT

This limited warranty covers only repairs or replacements of products manufactured by ADATA Technology Co. Ltd. and its authorized partners.
Please note that ADATA is responsible for providing free repairs except for the following reasons

The warranty label is altered, damaged or missing.
Product serial number does not conform to our original system.
Products purchased from an unauthorized agent.
Damage caused by natural calamity
Any abuse outside the intended product operation

ONLINE CUSTOMER SERVICE

For frequently asked questions, additional information and service instruction please visit the product page at www.xpg.com

IMPORTANT SAFETY INFORMATION

NEVER, under any circumstances, open the power supply unit or attempt to repair the power supply. This is extremely dangerous due to the high voltage inside.
DO NOT insert any objects into the fan grill or the ventilation area of the power supply unit.
DO NOT place any objects in front of the fan or the ventilation area of the power supply unit that may obstruct or restrict the airflow.
USE ONLY the modular cables bundled with the power supply unit. DO NOT use any third party cables or extension cables with this unit.
Avoid dust, humidity, and temperature extremes. Do not place the power supply unit in any area where it may become wet.
The power supply unit is for integration into a computer, and not intended for external or outdoor usage.
Failure to comply with any manufacturer instructions and/or any of these safety instructions will immediately void all warranties and guarantees.