VEVOR RA250200 Retractable Awning 8 x 7 ft Outdoor Patio User Manual
- June 17, 2024
- VEVOR
Table of Contents
VEVOR RA250200 Retractable Awning 8 x 7 ft Outdoor Patio
Introduction
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only
represents an estimate of savings you might benefit from buying certain tools
with us compared to the major top brands and doses not necessarily mean to
cover all categories of tools offered by us. You are kindly reminded to verify
carefully when you are placing an order with us if you are actually saving
half in comparison with the top major brands.
- RA250200
- RA300250
- RA350300
- RA400250
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
NOTICE:
- Protect from severe weather conditions.
- Wipe clean with a moist cloth and mild detergent.
- Do not use abrasive materials or cleaners.
- Carelessness causes fire-keep open flames away from covers.
- 2 people are recommended for mounting this product.
Please retain these instructions for future reference.
SPECIFICATIONS
| Model | RA250200 |
|---|---|
| Product Size | 8×7ft |
| Color | khaki |
| Model | RA300250 |
| --- | --- |
| Product Size | 10×8ft |
| Color | khaki |
| Model | RA350300 |
| --- | --- |
| Product Size | 12×10ft |
| Color | khaki |
| Model | RA400250 |
| --- | --- |
| Product Size | 13×8ft |
| Color | khaki |
PARTS LIST
Please prepare the following tools before installation (not included with the product).
-
Power drill
-
Tape
-
Wrench
-
Rubber Hammer
WARNING
Please read the instruction manual carefully before using it.
Please assemble this product strictly according to the instructions.
Please double-check that all parts of the package contents are intact.
Do not remove the safety casing that hold the arms down!
The mechanical arm will pop out immediately after the safety casing is
removed, which will cause damage to the assembler. Please do not remove the
safety casing.
Assembly Steps
Roller assemble: Insert the roller connector (A-2) into the right roller
(A-3) and secure it with the screw (S). Connect the left pulley
(A-1) with the pulley connector (A-2) and fix it with the screw
(S). Now you have a full-length roller.
Front Pole Assemble: Insert Front Pole Connector (D-2) into Right Front
Pole (D-3) and secure it with screw (S). Connect the left front rod
(D-1) to the connector (D-2) and secure it with the screw (S). You
now have a full-length front bar.
Unfold the awning fabric. You will have a large piece of fabric (C) and a
valance with a scalloped edge. You will also have three strips, two thick and
one thinner. Insert the thick and thin strips into both ends of the large
piece of fabric.
Put the end of the fabric with the thin strip in the groove of the roller.
Then put the end with the thick strip in the cut of the front bar and put the
end of the flounce with the thick strip in the other cut of it.
Roll up the interfacing cloth.
Slide the blocker (l) and arm-bar connector (K) into the passage /
slot in the wedge-shaped front bar, Cut off the excess part of the long strip.
Then pull the left and right plastic covers (H) on each end of the rod,
and then screw in the screw (R) on the plastic cover to secure the cover
(H) and strip (T) in place. Insert the rotator (V, W ) into
the roller (A).
| K X2PCS| | H X1PCS
---|---|---|---
| W X1PCS
| I X2PCS| | V X1PCS
Do not remove the safety sleeves that hold the arms down!
| M X4PCS
---|---
Slightly loosen the nut so that the parts can be moved left and right for
further assembly. Assembly of the entire awning: Insert the square shaft with
fabric into the square hole of the gear unit and connect it to the round shaft
on the right-hand side with a hammer.
Do not remove the safety sleeves that hold the arms down!
Loosen the nut slightly so that the parts can be moved left and right for
further assembly.
Assembly of whole awning: Insert the square shaft in the roller with fabric
into the square hole of the gearbox, and link it with a round shaft on the
right side using a hammer.
Pay attention to the winding direction of the cloth!
The next step is to unlock the security straps. We need to firmly grip the
limb of the movement arm bar with our hands to prevent the limb of the
movement arm bar from injuring people if it pops out of the safety band.
| Q X4PCS
---|---
| O X2PCS
Turn the handle and put the awning away.
After assembling put the two square cover (J) into the end of rod it.
| J X2PCS
---|---
Please prepare the following tools before installation (not included with the product).
Installation Procedure
-
Measure the distance along the wall where it can be placed. Drill holes for wall brackets on the wall according to the installation distances and height of the wall brackets. The diameter and depth of the hole must be the same as the expansion bolts.
The holes of each group must be on the same line in transversal direction and vertical direction.
( Note : It is recommended to draw lines on the wall first to ensure the precise position and size of the holes) -
Hammer all the expansion bolts into the holes. Then take down the nuts and washer.
( Note : ① The expansion bolts must be hammered into the wall completely.
② The bolts must be stuck out of the wall so that the wall brackets can be installed on it.
③ The nut and washer might be separated from the bolt during the process of transportation.
Please put them back into their original positions before hammering them into the wall.) -
Take down the original bolts of the wall brackets, as shown in the figure. Use expansion bolts to fix the wall brackets on the wall. Do not tighten completely. Leave wall brackets to stay on the wall with a little movement.
Installation distance between wall brackets- Awning < 3m Only 2 wall brackets for each end of the torsion bars.
- Awning 3.5m ~ 4.5m 2 wall brackets at each end of the torsion bar, a middle bracket in between the distance of 2 arm shoulders (arm brackets refer to steps of assembly 6)
- Awning > 5m 2 wall brackets at each end of the torsion bar, 2 middle brackets divide into equal lengths in between the distance of 2 arm shoulders at each end of the torsion bars.(Steps of assembly 6)
-
As shown in the figure, we recommend making the awning surface to form an angle of about 80 degrees with the wall when it is open.
A ) The height of the front bar you desire
L ) The length of the arm stretches out
C ) The height of wall brackets
You can follow this formula: C= A + 0.17*L
-
Install the awning on the wall brackets according to “Installation distances between wall brackets” above, put the original bolts on the wall brackets and tighten them. Finally, fasten all expansion bolts.
CAUTION : Proper location of the brackets is the most important aspect of the awning installation. It is critical that you fasten all the mounting brackets to studs, joists, headers or other major structural components.
WARNING : Failure to securely fasten all the brackets to the wall could result in the collapse of the awning and cause personal injury or death. -
Instruction for front side leveling.
① Loosen the locking nuts.
② Turn the jack bolt to adjust the pitch
③Adjust the arm until the front side stays in a horizontal line.
④Tighten the locking nuts.
Warning: When the front bar touches the roller as shown in the figure don’t try to make them closer otherwise the product might be damaged.
FAQ : What if the fabric wraps unevenly or the arms cannot open at the
same time?
Answer : Check the stability of the two arms and adjust the front
handlebar wrist of the faster arm outwards accordingly.
◎Hang the Hand Crank on the Rotation Ring. You can rotate the Hand Crank in a
Clockwise/Anticlockwise direction to stretch/contract the awning flexibly.
◎When the awning is fully extended, the arm link on both sides is about 8”
from the edge, but it must be noted that the distance between the two sides
must be consistent. Otherwise, it will cause uneven stretching of the product.
| Questions | Answers |
|---|
When I open the awning, why the front bar will pull the Fabric and Valance toward one end?| A1: There are two possible reasons for uneven product stretching:
- The fabric is not evenly rolled.
- The distance between the two ends of the bent arm is inconsistent.
What should I do if the front bar pulls the Fabric and Valance toward one end?| A2: You should check if the fabric rolled evenly and adjust the arm bar link by follow these steps:
- First, take back the awning and fix the arm with straps to prevent the spring from hurting people.
- Adjust the distance between the arm bar link and both ends to be consistent, about 8”.
- Reinforce the screws of the link of the arm bar so that it is not easy to slide.
Address : Baoshanqu Shuangchenglu 803long 11hao 1602A-1609shi Shanghai
Imported to AUS : SIHAO PTY LTD, 1 ROKEVA STREETEASTWOOD NSW 2122
Australia Imported to USA: Sanven Technology Ltd.Suite 250, 9166 Anaheim
Place, Rancho Cucamonga, CA 91730
SHUNSHUN GmbH Römeräcker 9 Z2021,76351 Linkenheim-Hochstetten,Germany
Pooledas Group Ltd Unit 5 Albert Edward House, The Pavilions Preston, United Kingdom
Customer Support
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
TOUGH TOOLS, HALF PRICE
Technical Support and E-Warranty Certificate
www.vevor.com/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>