ALMOST HEAVEN SAUNAS Himalaya 6 Person Indoor Sauna Owner’s Manual

June 17, 2024
ALMOST HEAVEN SAUNAS

ALMOST-HEAVEN-LOGO

ALMOST HEAVEN SAUNAS Himalaya 6 Person Indoor Sauna

Himalaya 6 Person Sauna
Specifications:

  • Capacity : 6 persons
  • Electrical Requirements : Refer to the user manual for details
  • Surface Compatibility: Concrete, tile, vinyl, laminate

Product Usage Instructions

  1. Floor Assembly:
    Begin by placing the base frames on the floor and install the dovetail key into both corners.

  2. Wall Assembly:
    Fasten the wooden panels to the corner posts using screws and predrilled holes. Ensure corner posts are fully locked into place.

  3. Salt Wall Lights:
    Screw in light bar clips above and below the salt blocks. Snap the light bars into the clips, ensuring proper alignment for cord direction towards the outlet.

  4. Front Glass Assembly:
    Apply aluminum U channel to the glass pieces and place them into the designated grooves on the corner posts. Note the orientation of the glass for swing direction of the door.

FAQ :

  1. Q: Can the sauna be placed on carpet?
    A: It is not recommended to place the sauna on carpet. Ensure a flat and level surface like concrete, tile, vinyl, or laminate.

  2. Q: How many people are recommended for assembly?
    A: It is recommended that two people complete the assembly of the sauna for ease and efficiency.

  3. Q: How to change the swing direction of the door?
    A: Swap the two pieces of glass to change the swing direction of the door.

Himalaya 6 Person Sauna

Installation & Owner’s Manual

Read this entire manual through to the end before proceeding with the assembly.

ELECTRICAL REQUIREMENTS

  • All electrical wiring must be performed by A QUALIFIED LICENSED ELECTRICIAN. Costs of an electrician can vary greatly depending on several factors, including your sauna’s distance from your electrical service box, where you live and cost of materials. We always recommend you get quotes from two to three different licensed electricians before you begin installation in order to get the best possible service and price.
  • Use copper wire with 90C insulation. Do not use aluminum wire to make the connection. Consult with an electrician so you can determine the requirements for your particular situation. All wiring must conform to all national, state and local codes and regulations. For further information and instruction on your heater installation and operation, please consult the provided heater manual.

BASIC TOOLS

  • These tools are helpful in the assembly of your Himalaya sauna:
    • Cordless drill with 1/8” & 3/8” drill bits, and Phillips bit
    • ½” or 5/8” Forstner Bit (For Heater Install)
    • Rubber mallet
    • 1.5mm Hex Wrench or Socket
    • Framing square
    • Utility knife
    • Level
    • Ladder or Stepstool
  • NOTES FOR ASSEMBLY
    Be sure the surface where you are placing the sauna is flat and level. A concrete, tile, vinyl, laminate or similar surface is suitable; placing the sauna on carpet is not recommended. We recommend that two people complete the assembly of the sauna. Should you have any questions during assembly, please feel free to call us at 888.355.3050, or email sales@almostheaven.com.

Kit will contain the following components, as well as labeled bags of screws and hardware:

  1. 1 – Base Frame, Rear
  2. 1 – Base Frame, Right
  3. 2 – A/B Wall Panel with Multiclip
  4. 1 – A/B Salt Stone Wall Panel, Ventilation Cutout 1 – Front Wall Header
  5. 2 – Corner Post 90° with Multiclip and Groove – Left & Right 2 – Corner Post 90°
  6. 4 – Roof Support Slats
  7. 2 – Upper Benches (2 different lengths)
  8. 1 – Upper Bench End Trim
  9. 1 – Lower Bench
  10. 1 – Glass Door
  11. 1 – Glass Panel
  12. 1 – Stainless Steel Post (post and bench attachment) 2 – Headrest
  13. 1 – Set of Door Hinges
  14. 2 – Salt Wall Lighting LED
  15. 1 – Hardware Bag
  16. 1 – Base Frame, Left
  17. 6 – A/B Wall Panels
  18. 3 – A/B Salt Stone Wall Element 2 – A/B Roof Panel
  19. 2 – A/B Roof Panels with Grooves
  20. 5 – Bench Support Slats (3 different lengths) 2 – Mounting Slats for Bench Screen
  21. 1 – Bench Screen
  22. 2 – Backrests (2 different lengths)
  23. 1 – Ventilation Cover
  24. 1 – Glass Panel with Holes for Door Hinges 2 – Roof Trim Slat
  25. 2 – “U” Aluminum Profile
  26. 1 – Door Handle Set
  27. 1 – Door Magnet & Sleeve Plate

It is suggested that you lay out all of the components so that it is easy to identify the pieces once you get started with assembly.

FLOOR ASSEMBLY

Begin assembly by placing the three base frames on the floor (1). Using your rubber mallet, install the dovetail key into both corners (2). You will need access to the rear of the sauna, so ensure it is far enough away from a wall to gain access.ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(1\)

WALL ASSEMBLY
Begin assembling walls by placing salt stone wall with ventilation hole on the rear base on the right-hand side (3). Place a 90° corner post next to the salt stone panel (4). Fasten corner post to the wall panel using screws through the predrilled holes in the corner post (5-6). ALMOST-HEAVEN-SAUNAS-Himalaya-6
-Person-Indoor-Sauna- \(2\)

Place a solid wood wall panel next to the corner post (7). Fasten this panel to the corner post using screws and predrilled holes as done above (5-6). Now place two more similar panels next to it. Then place a wooden panel with multiclips into the side on the front right corner (8). Now slide the right front corner post down over the multiclips on the wall panel (9). Make sure the corner post is fully locked into place; tap top with rubber mallet if necessary. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(3\)

Now place the remaining three salt stone wall panels on the back wall (10). Similar to (4-6) above, place the corner post and fasten using the predrilled holes (11-12). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(4\)

Assemble the left wall using wooden panels as (7-9) above. Fasten the first panel to the corner post using screws through predrilled holes in corner post. Place two more wooden panels, followed by a wooden panel with multiclips (13-14). Now place the left corner post by sliding the multiclips over the clips on the end panel (15). Make sure the corner post is fully locked into place; tap top with rubber mallet if necessary. ALMOST-HEAVEN-SAUNAS-
Himalaya-6-Person-Indoor-Sauna- \(5\)

Finish the wall assembly by inserting a screw through the top on an angle to connect the middle panel to the adjacent outer panels (16-18). Red lines below show the direction to install the screws. ALMOST-HEAVEN-SAUNAS-Himalaya-6
-Person-Indoor-Sauna- \(6\)

SALT WALL LIGHTS
Screw in a light bar clip roughly 6” in on each end, above and below the salt blocks (19). Also install one midway between these clips, ensure it is line with the first clips so the light bar snaps into the clips correctly. Snap the light bars into the clips, with the cord going in the direction of the nearest outlet (20). Now the sauna can be carefully slid into the final location to finish the assembly. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(7\)

FRONT GLASS ASSEMBLY
Take the solid piece of glass with and apply the aluminum “U” channel to the bottom, then place into the groove on the left corner post. (21). Repeat for the side piece of glass with hinge holes on the right side. Orient the glass so the holes are towards the middle (22-23).
NOTE: Door can swing either direction, to change swing direction, swap these two pieces of glass. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-
Sauna- \(7\)

Place the header over the glass panels and insert the dowel pins into the predrilled holes in the corner posts (24-25). You may need to tap slightly with the rubber mallet to fully insert the pins into the holes. ALMOST-
HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna- \(7\)Fasten the header to the corner posts by inserting a screw on an angle on both ends (26). ROOF ASSEMBLY
Locate the four roof support slats. Measure in 4” and 27” from both ends and drill a hole using 1/8” drill bit (27).
Screw roof supports top of each wall using holes you drilled in previous step; ensure the top of the support is flush with the top of the wall (28-30). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(11\)

Place one of the roof panels that has a notch on three sides onto the roof support slats (31-32). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(12\)

Next to it, place the two panels that have one tongue edge and one groove edge, and match the edge with the first panel you placed (33). Then carefully slide the last roof panel into place (34). ALMOST-HEAVEN-SAUNAS-Himalaya-6
-Person-Indoor-Sauna- \(12\)

Fasten the roof panels to the roof support slats using screws (35).

BENCH ASSEMBLY
In each inside back corner, measure up 32-1/4” from the floor and make a mark (36). Place the top of a short bench support brace at the mark, running from the back corner towards the front (37). Repeat for right side bench support. Back on the left wall, measure up 14-1/8” and make a mark (38). Place the top of a long bench support on the mark, running towards the front and fasten into place (39). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(15\)

Place the bench screen mounting slats beneath the front end of the bench support slats installed above (37) and fasten into place (40). Repeat for right side wall. On the right wall, measure 13-1/4” from where the top bench support stopped, towards the front wall. Place the medium bench support starting at that mark, running towards the front and fasten into place (41). Place the ventilation cover over the hole in the wall panel and fasten into place (42). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(16\)

Place a long bench onto the lower bench support braces and another on the upper braces (43-44). Tilt up so its leaning against the back wall. (44-45). Place the bench screen in front of the screen mounting slats and fasten (45-46 ).ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(17\)

Locate the shorter upper bench panel and bench end trim. Fasten the trim to the end of the bench that will be facing the glass wall panel (47). Place the post bench attachment in the corner on the end you installed the end trim and fasten into place (48). Place the post over the bench attachment and tighten the set screw (49). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(18\)

Place the bench on the bench support (41, 50) and fasten into the long upper bench (50-51). Slide the rubber boot onto the base of the bench support post (52). ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(19\)

BACKREST INSTALLATION

From the top of the long bench measure up 11”, this will be the placement for the bottom of the long backrest. Place the bottom of the long backrest at the 11” mark and fasten into place (53,54). Repeat for the short back rest. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(20\)

ROOF TRIM INSTALLATION
Place the roof trim pieces on the front and left-hand sides (55). Front left corner should have 45° mitered corner when placed correctly (56). Fasten to roof my installing screws down through top of trim (57). ALMOST-HEAVEN-
SAUNAS-Himalaya-6-Person-Indoor-Sauna- \(21\)

DOOR INSTALLATION
Place the hinge on the outside of the sauna, and then the plate on the inside and fasten together (58-59). Complete for both hinges. ALMOST-HEAVEN-SAUNAS-
Himalaya-6-Person-Indoor-Sauna- \(22\)

Measure 1-3/4” over from the solid glass panel on the gasket and make a cut (60). Measure over another 3/8” of an inch and cut again, remove the piece of gasket and install the magnet catch (61). Have someone hold the door and attach using hinges and process used above (59, 62). Once door is fastened with both hinges, close the door and ensure the catch aligns with the magnet (63). Slide the metal catch on the door as required to align with magnet. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(23\)

When installing the door handle, the metal part is out the outside of the sauna and the wooden on the inside. Place a plastic spacer between the metal and the glass, and then another between the wood and the glass. Place the screw through the hole in the wood and loosely screw it into the metal piece (64). Place spacers on the bottom as done for the top and loosely fasten this as well (65). Finish tightening screws so door handle is tight and straight vertically. ALMOST-HEAVEN-SAUNAS-Himalaya-6-Person-Indoor-Sauna-
\(24\)

FINAL THINGS

  • Once assembly is complete, sweep and vacuum the inside of the sauna. Wipe down the entire interior with a damp cloth to remove any remaining dirt, dust and debris. Do not use any cleaning supplies, unless they are specifically for sauna use.
  • The salt stones will attract moisture, which will cause the formation of salt crystals. Clean the salt crystals regularly with a damp cloth, do not sure cleaning supplies on the salt stones.
    HEATER – Please see heater manual.

TRADITIONAL SAUNA USE

  • Congratulations! You are ready to enjoy your sauna! You may use your sauna in a wet or dry fashion. A dry sauna means you do not sprinkle any water onto the stones, while wet means you increase the humidity of the room by sprinkling water on the stones. Please note that not much water is needed to achieve a wet sauna experience. The sauna as we know it originates in Finland. The typical sauna experience follows the steps below, but you may enjoy your sauna in any way you like!
    • Set your heater so your sauna achieves the desired temperature. This is typically160-185+°F. Please note, novice sauna users should begin at the lower end of that range and increase their high temperature over time.
    • Take a quick shower or a quick dip in a hot tub or pool.
    • Step into the sauna and enjoy for 5-15 minutes, bringing a towel to sit or lay on. Leave the sauna once you are perspiring freely.
    • Take a plunge in a pool, shower, snowbank, lake – anything that will cool you down! After that, relax and cool down for 10-20minutes.
    • Step into the sauna again. During this visit, you may wish to sprinkle small amounts of water onto the stones to create bursts of steam. If water spills through the heater to the floor, you are using too much water, though this will not hurt the heater or the sauna.
    • Continue repeating this process. After your final visit to your sauna, relax for at least 20 minutes. Shower with warm water initially, finishing with cool water to close your skin pores.
    • Prepare to feel refreshed for the day or to have an amazing night’s sleep! Whatever your sauna routine, it is imperative that you STAY HYDRATED!

Optional accessories for your sauna, including a back rest, robe hook and much more are available at almostheaven.com/sauna- accessories/
HIMALAYA 6 PERSON SAUNA INSTALLATION MANUAL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

ALMOST HEAVEN SAUNAS User Manuals

Related Manuals