LED SOLUTION 191025 Premium Dustproof Light Owner’s Manual
- May 15, 2024
- LED Solution
Table of Contents
LED SOLUTION 191025 Premium Dustproof Light
Specifications
- Model:
- LED dust proof light 120cm 36W 150lm/W Premium
- LED dust proof light 150cm 48W 150lm/W Premium
- Product code: 191025, 191026
Dimensions
- 120cm light: 1260 x 79 x 68 mm
- 150cm light: 1560 x 79 x 68 mm
- Input voltage: AC 220-240V, 50-60Hz
- Power: 36W for 120cm, 48W for 150cm
- Color temperature: 4000-4500K
- Luminous flux: 5400lm for 120cm, 7200lm for 150cm
- Beam angle: 120 degrees
Product Usage Instructions
- Disconnect the power supply before installation.
- Drill holes to install the fixture securely.
- Remove the connector from the fixture.
- Insert the wire into the connector ensuring a maximum cross-section.
FAQ
-
Q: What should I do if the light is not turning on?
A: Check the power supply connection and ensure it is securely connected. Verify that the wires are properly inserted into the connector. -
Q: Can this light be used outdoors?
A: Yes, this light has an IP65 rating, making it suitable for outdoor use as it is dustproof and water-resistant. -
Q: What is the recommended mounting height for this light?
A: The recommended mounting height for optimal lighting performance is between 7mm to less than 20mm.
Manual Dustproof light Premium
Model| Product code| DimensionL x W x H (mm)| Input voltage AC(V) 50 – 60 Hz|
Power (W)| Color temperature (K)| Luminous flux (lm)| Beam angle (°)
---|---|---|---|---|---|---|---
LED dust proof light 120cm36W 150lm/W Premium| 191025| 1260 x 79 x 68| 220 –
240| 36| 4000 – 4500| 5400| 120
LED dust proof light 150cm48W 150lm/W Premium| 191026| 1560 x 79 x 68| 220 –
240| 48| 4000 – 4500| 7200| 120
General instructions and important safety information
- Please read this manual carefully before using the product and keep it for future reference.
- For damage caused by improper use or changes in the product structure, LED Solution s.r.o. bears no responsibility.
- Before handling the product in any way, make sure that the power supply is switched off.
- All activities performed on electrical equipment must only be performed by a person with electrical technical qualifications.
- The product is intended for use in indoor and outdoor environments IP65.
- The light source of this lamp is non-replaceable, after the end of the life of the lamp or damage to the cover, the entire lamp must be replaced.
- When assembling, use only the parts that are included in the delivery.
- After installation, make sure the fixture is well fixed to the ceiling or wall.
- Moistened cotton is best for cleaning the lamp. Do not use solvents, thinners or alcohol for cleaning.
- If a fault is detected, disconnect the power supply from the socket or switch off the relevant circuit breaker, secure the body and do not use the lamp until the fault has been professionally repaired.
- Disconnect the power supply,
- Drill the holes to install the fixture,
- Remove the connector,
- Insert the wire into the connector, max. cross-section 3×0.75 mm² – 3×1.5 mm², pay attention to the correct connection of the wires (black or brown – L, blue – N, green-yellow – PE),
- Insert the connector and tighten,
- Insert dowels into the holes and attach the sheet metal holder with screws,
- Snap the lamp into the metal holder,
- Turn on the power supply. Energy.
LED
Solution s.r.o.,Dr. Milady Horakove185/66, Liberec 460 07, Czech Republic
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>