LED s light 800800 LED Wall And Ceiling Light User Manual

LED s light 800800 LED Wall And Ceiling Light User Manual

Instructions

Replaceable LED to minimize waste

Suitable for moist environments [IP44]

Sensor
800801

Detection area

Hold time

Daylight

**Sensor

**

Warning:

Ensure you have fully read and understood the instructions in this document before you install or use the product. Keep this document for future reference. Only use the product as described in this document. Any other use of the product than described in this manual may damage the product or cause injury to the user (e.g. due to a short circuit, fire or electric shock). Do not use the product if a part is damaged or defective. Replace a damaged defective product immediately. Do not drop the product and avoid bumping. This product may only be serviced by a qualified technician to reduce the risk of electric shock. Disconnect the product from the power source if problems occur. make sure the product is sufficiently ventilated during use. never cover the lamp during use. Keep the product out of reach of children or animals. Do not look directly at the product during use. The LED lights are extremely bright and may cause serious eye damage. The electrical components of the product must be earthed. Do not use the product if a part is damaged or defective. Replace a damaged or defective device immediately.

Product description

The Shada LED wall and ceiling light is a smart LED lamp that can be installed on a wall or ceiling. 800801 has a control unit that contains a microwave motion sensor and a daylight sensor, as well as four switches to adjust the settings of these sensors. The motion sensor allows the lamp to turn on automatically when someone enters the room. The daylight sensor allows the lamp to turn on automatically when the room is dark.

Installation

Replacing LED unit

Thank you for purchasing the Shada LED wall and ceiling light.

Please read this manual carefully before installing, using or performing maintenance on the product. Formal documentation is available upon request. The formal documentation includes, but is not limited to:

• the declaration of conformity
• the material safety datasheet
• the product test report
• Product design and specifications are subject to change without notice. All logos and trade names are registered trademarks of their respective owners and are hereby acknowledged as such.

Intended & unintended use

The LED wall and ceiling light is intended to:

• be used to light an indoor or outdoor domestic environment.
• to be installed on a wall or ceiling, according to the instructions provided in this document.
• be turned on or off by a control switch via a 230 V mains power supply.

The product may not be changed or adapted. Do not use the product for other purposes than described in this manual.

Warranty

This product comes with a warranty period of 24 months.
Any changes and/or modifications to the product will void the warranty. We cannot accept any liability for damage caused by incorrect use of the product.

Contact information

For more information about the product or this document, please contact:

Shada BV
info@shada.nl
Molenmakershoek 28
7328 JK, Apeldoorn
The Netherlands

Installing the lamp

Take note of the safety instructions in chapter ‘Safety’ before installing the product.
-Always shut off power to the circuit before starting installation work. -In some countries electrical installation work may only be carried out by a authorised electrical contractor. Contact your local electricity authority for advice.

Preparation

1. Check the product for visible damage. If damaged, it must not be put into operation.
2. For safe and correct installation, supply yourself with the necessary tools (image 2).

Adjust the lamp settings 800801:

The four switches on the control unit can be used to adjust the settings of the lamp:

• Use switch 1 to adjust the detection area of the motion sensor.
• Use switch 2 and 3 to adjust the time before the lamp turns off.
• Use switch 4 to enable or disable the daylight sensor.

Installation

1. Decide where you want to install the product.
2. Disable the mains power to the room in which you will install the product.
3. Use the base plate to mark the drill holes on the wall or ceiling.
4. Drill three 05 mm holes of 40 mm deep.
5. Insert the wall plugs.
6. Different ceilings or walls require different types of connections. Always choose screws and plugs that are specially suited to the material.
7. Guide the mains power cable through the hole in the lamp housing.
8. Place the base plate and insert the screws to fix the bracket in place.
9. Connect the power cable
10. Close the junction box.
11. Install the lamp cover

Replace the LED unit:

Switch the main power off and uninstall the lamp first!

1. Unscrew the junction box cover.
2. Disconnect the cables.
3. Unscrew the unit.
4. Connect the cables of the new unit.
5. Close and screw the junction box cover.
6. Screw the unit in its place.

Maintenance

Cleaning

• Clean the outside of the product using a soft, damp cloth.
• Do not clean the inside of the product.
• Do not use cleaning solvents or abrasives.

Repair
This product may only be serviced by a qualified technician to reduce the risk of electric shock.

Symbols on the product and/or packaging

protect against electric shock, such as double insulation or reinforced insulation.| |
| The product contains a non-dimmable lamp| |
| The item should be disposed of separately from household waste. The item should be handed in for recycling in accordance with local environmental regulations for waste disposal. By separating a marked item from household waste, you will help reduce the volume of waste sent to incinerators or land- fill and minimize any potential negative impact on human health and the environment.| |
| This product carries the CE mark of certification, which confirms that this product meets EU safety, health and environmental protection requirements.| |
| Caution! Risk of electric shock.| |

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>