Samsung LH65WMBWBGCXXY Flip Pro WMB Interactive Flat Panel User Manual

Flip
User Manual
WM55B WM65B WM75B WM85B

The colour and the appearance may differ depending on the product, and the content in the manual is subject to change without prior notice to improve the performance.
Recommended hours of use per day of this product is under 16 hours. If the product is used for longer than 16 hours a day, the warranty may be void.
[For India Only] This product is RoHS compliant.
For more information on safe disposal and recycling visit our website www.samsung.com/in or contact our Helpline numbers 1800 40 SAMSUNG (1800 40 7267864)  (Toll-Free) 1800 5 SAMSUNG (1800 57267864) (Toll-Free)
© Samsung
Samsung owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung is prohibited.
Trademarks other than Samsung are property of their respective owners.

Before using the product

Safety precautions
The following safety instructions are to ensure your personal safety and prevent property damage. Please read the following to ensure the proper use of the product.
Safety symbols

followed.
| Caution| Personal injury or damage to properties may result if instructions are not followed.
| Prohibition| Do NOT attempt.
| Instruction| Follow directions.

CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.

| This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
---|---
| This symbol indicates that this product has included important literature concerning operation and maintenance.
****| Class II product: This symbol indicates that a safety connection to electrical earth (ground) is not required. If this symbol is not present on a product with a mains lead, the product MUST have a reliable connection to protective earth (ground).
| AC voltage: Rated voltage marked with this symbol is AC voltage.
| DC voltage: Rated voltage marked with this symbol is DC voltage.
| Caution. Consult instructions for use: This symbol instructs the user to consult the user manual for further safety related information.

CAUTION
RISK OF ELECTRIC SHOCK. DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.

| This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.| | AC voltage: Rated voltage marked with this symbol is  AC voltage.
---|---|---|---
| This symbol indicates that this product has included important literature concerning operation and maintenance.| | DC voltage: Rated voltage marked with this symbol is  DC voltage.
| Class II product: This symbol indicates that a safety connection to electrical earth (ground) is not required. If this symbol is not present on a product with a mains lead, the product MUST have  a reliable connection to protective earth (ground).| | Caution. Consult instructions for use: This symbol  instructs the user to consult the user manual for further  safety related information.

Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create white-coloured stains on the product.
” Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be charged).

Electricity and safety
Warning
Do not use a damaged power cord or plug, or a loose power socket.
An electric shock or fire may result.
Do not use multiple products with a single power socket.
Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Do not bend or pull the power cord with force. Be careful not to leave the powercord under a heavy object.
Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
A fire or electric shock may result.
Insert the power plug all the way in so it is not loose.
An unsecure connection may cause a fire.
Connect the power plug to a grounded power socket (type 1 insulated devices only).
An electric shock or injury may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
A fire may result.

Caution
Do not disconnect the power cord while the product is being used.
The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power cord with other products.
A fire or electric shock may result.
Keep the power socket where the power cord is connected unobstructed.
The power cord must be disconnected to cut off power to the product when an issue occurs.
Hold the plug when disconnecting the power cord from the power socket.
An electric shock or fire may result.

Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
A fire may result.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
An increased internal temperature may cause a fire.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.)

• The product may fall and become damaged and/or cause an injury.
• Using the product in an area with excess vibration may damage the product or cause a fire.

Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
The product lifespan may be reduced or a fire may result.

Do not install the product within the reach of young children.

• The product may fall and injure children.
• As the front is heavy, install the product on a flat and stable surface.

Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter.
Have a technician install the wall-mount hanger.

• Installation by an unqualified person can result in an injury.
• Only use approved cabinets.

Install the product at least 10 cm away from the wall to allow ventilation.
An increased internal temperature may cause a fire.
Keep the plastic packaging out of the reach of children.
Children may suffocate.
Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke.
A fire or electric shock may result.

Caution
Do not set down the product on its front.
The screen may become damaged.
Do not drop the product while moving.
Product failure or personal injury may result.
Set down the product gently.
Product failure or personal injury may result.
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical substances, extreme temperatures or a significant presence of moisture, or a place where the product will operate continuously for an extended period of time) may  seriously affect its performance.
Be sure to consult Samsung Customer Service Centre if you want to install the product at such a place.

Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the product yourself.

• A fire or electric shock may result.
• Contact Samsung Customer Service Centre for repairs.

Do not let children hang from the product or climb on top of it.
Children may become injured or seriously harmed.
If the product is dropped or the outer case is damaged, turn off the power switch and disconnect the power cord. Then contact Samsung Customer Service Centre.
Continued use can result in a fire or electric shock.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product.
The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury.
Do not move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Do not lift or move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Ensure the vents are not blocked by tablecloths or curtains.
An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/output ports, etc).

• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Centre.
• Product failure, an electric shock or fire may result.

Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on top of the product.

• Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Centre.
• Product failure, an electric shock or fire may result.

Before moving the product, turn off the power switch and disconnect the power cable and all other connected cables.
Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the power cord immediately and contact Samsung Customer Service Centre.
An electric shock or fire may result.

During a lightning or thunderstorm, power off the product and remove the power cable.
A fire or electric shock may result.
Do not drop objects on the product or apply impact.
A fire or electric shock may result.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
Sparks can cause an explosion or fire.
Do not use or keep combustible spray or an inflammable substance near the product.
An explosion or fire may result.

Caution
Do not use humidifiers or stoves around the product.
A fire or electric shock may result.
Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.

Do not place heavy objects on the product.
Product failure or personal injury may result.

Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels.
Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time.

Disconnect the power cord from the power socket if you do not plan on using the product for an extended period of time (vacation, etc).
Dust accumulation combined with heat can cause a fire, electric shock or electric leakage.

Use the product at the recommended resolution and frequency.
Your eyesight may deteriorate.

Looking at the screen too close for an extended period of time can deteriorate your eyesight.

Rest your eyes for more than 5 minutes for every 1 hour of product use.
Eye fatigue will be relieved.

Store small accessories out of the reach of children.

Precautions for use

Be careful that if you use the supplied pen with a load exceeding 2.5 kg, scratches may occur on the protective glass.
If you use a ballpoint pen other than the supplied pen, be careful that the screen may be stained with ink or damaged.
Do not use a dirty brush to avoid screen damage.
We recommend that you use the supplied pen. Do not use sharp, pointed objects other than the pen.
If dust or dirt from the supplied pen remains on the protective glass, clean it referring to the instructions below.

Cleaning the exterior and display
Wipe the surface with a slightly wet, soft cloth, and then wipe with a dry cloth.

Chapter 02  Preparations

Contact the vendor where you purchased the product if any components are missing.
  The appearance of the components may differ from the images shown.
  Refer to the installation guide for the WMB stand or wall mount
(available for optional purchase).

Checking the components

Parts

The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

turn off the
product.
The power indicator is off when the product is on.
The power indicator is on when the product is off.
In writing mode, shortly press the Power button to switch to the screen saver mode.
In case the PIP screen is in Full Screen mode, press the Power button to display the adjustment menu. Press again to hide.
| The pen is magnetic. Keep it by attaching to the marked location.
A  : WM55B, B  : WM65B

The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Power button &
indicator| Press the button to turn on the product and press and hold the button to turn off the
product.
The power indicator is off when the product is on.
The power indicator is on when the product is off.
In writing mode, shortly press the Power button to switch to the screen saver mode.
| The pen is magnetic. Keep it by attaching to the marked location.
Light sensor| The light sensor is used to detect ambient light for the Brightness Optimisation
function.
• You can turn on or off the Brightness Optimisation function at  Menu → SETTINGS → System → Advanced Settings →  Brightness Optimisation.
OPS case (Sold separately)| Connect the OPS case to the product and insert the standard OPS module into the case. You can purchase the OPS case and  module separately.
Before inserting the OPS module, make sure to remove the power cable from the product to completely cut off the power  supply.
OPS refers to the Intel Open Pluggable Specification.
When the OPS case needs to be installed, be sure to install the OPS case first before the product.
OPS power supply: 16 V/4.5 A

Ports

The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

The USB ports on the product accept a maximum constant current of 1.0 A. If the maximum value is exceeded,  USB ports may not work.
 LAN| Connects to a network using a LAN cable. (10/100 Mbps)
Use Cat7(*STP Type) cable for the connection.

• Shielded Twist Pair.
   SERVICE| Dedicated to service technicians.
  This port is for servicing only and has no user function. Do not connect a cable to this port.
   HDMI | Connects to a source device using a HDMI cable.
   DP | Connects to a source device using a DP cable.
   TOUCH | Allows touch-based control of the PC screen connected through the HDMI   or DP  port. Use the supplied USB  cable to connect between the TOUCH port on the rear of the product and the PC.
  | Outputs sound to an audio device via an audio cable.

The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

 USB
(1A)| Connect to a USB memory device.
The USB ports on the product accept a maximum constant current of 1.0 A. If the maximum value is  exceeded, USB ports may not work.
| Outputs sound to an audio device via an audio cable.
 SERVICE| Dedicated to service technicians.
This port is for servicing only and has no user function. Do not connect a cable to this port.
 HDMI  1| Connects to a source device using a HDMI cable.
 DP | Connects to a source device using a DP cable.
 TOUCH  | Allows touch-based control of the PC screen connected through the HDMI   1 or DP   port. Use the supplied  USB cable to connect between the TOUCH   port on the rear of the product and the PC.
 LAN| Connects to a network using a LAN cable. (10/100 Mbps)
Use Cat7(*STP Type) cable for the connection.

• Shielded Twist Pair.

Tray

Trays are sold separately. Contact your vendor for assistance to make a purchase.
The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.
The product must be powered off when you install the tray.

 EXTERNAL
(USB)| Provides USB connectivity to PC.
1 Use a USB cable to connect EXTERNAL   (USB) to the connected PC.
2 Connect the USB device to EXTERNAL   (USB).
3 A connection is established between the USB device and PC.
 EXTERNAL
(USB)
 TOUCH| Allows touch-based control of the PC screen connected through the HDMI 2 port.
Use the supplied USB cable to connect between the TOUCH   port on the tray and
the PC.
 HDMI  2| An HDMI port for displaying input from an external source.
| You can connect a device using a USB-C cable.
• USB-C connection allows video output and touch-based control of the device.
Data transfer is not supported.
You must use a USB-C cable that supports video transmission. Use a cable that supports DP ALT Mode (Video transmission).
Use a USB-C cable that is 1 m or shorter in length.
Charing is also supported up to 15 W (5 V/max 3 A). Charging with USB-C cable is only available when  the product is on.

The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality.

Ports

 EXTERNAL
(USB 3.0)| Provides USB connectivity to PC.
1 Use a USB cable to connect EXTERNAL   (USB 3.0) to the connected PC.
2 Connect the USB device to EXTERNAL   (USB 3.0).
3 A connection is established between the USB device and PC.
 EXTERNAL
(USB 3.0)
 USB| Connect to a USB memory device.
 TOUCH | Allows touch-based control of the PC screen connected through the HDMI   2 port.
Use the supplied USB cable to connect between the TOUCH   port on the tray and the PC.
 HDMI 2| An HDMI port for displaying input from an external source.
(65 W)| You can connect a device using a USB-C cable.
• USB-C connection allows video output, touch-based control of the device and you can also charge the  connected device.
Data transfer is not supported.
You must use a USB-C cable that supports video transmission and charging function. Use a cable that  supports DP ALT Mode (Video transmission) and Power Delivery (65 W or higher).
Use a USB-C cable that is 1 m or shorter in length.
Charging with USB-C cable is only available when the product is on.

Buttons

to close the menu.
| Press the button to use the Freeze Frame function. The source screen will be paused on the Flip screen, but it does  not affect the source device. Press the button again to cancel the function.
| Press the button to use the Block Screen function. The contents on the screen will be covered in black. Press the  button again to cancel the function.
| You can turn the Note on or off.
| Adjust the volume.
If you have connected two Bluetooth speakers, volume control is only available when connected speakers support  the AVRCP (Audio Video Remote Control Profile). (AVRCP is supported on Samsung Soundbars released in 2021 and later.)

Before installing the product (Installation guide)

This product can be wall-mounted. The exclusive Samsung stand (for WM55B) and wall mount (for WM65B) are available for optional purchase.
Do not install or use the product with its front facing up. Touch-based functions may not work properly.

WM55B
Rotation
Contact Samsung Customer Service Centre for further details.

• To use the product in landscape mode, turn it anticlockwise and make sure the power indicator is on the right after turning.

Ventilation
Contact Samsung Customer Service Centre for further details.
Installation on a perpendicular wall
A Minimum 15 mm
B Ambient temperature: 35 °C or less
” When installing the product on a perpendicular wall, allow at least 15 mm of space between the product and wall surface for ventilation and ensure that the ambient temperature is kept below 35 °C.

Installation on an indented wall
A Minimum 15 mm
B Minimum 25 mm
C Ambient temperature: 35 °C or less
When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 °C.

WM65B
Ventilation
Contact Samsung Customer Service Centre for further details.
Installation on a perpendicular wall
A Minimum 0 mm
B Ambient temperature: 35 °C or less

Installation on an indented wall
A Minimum 0 mm
B Minimum 25 mm
C Ambient temperature: 35 °C or less
When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 °C.

WM75B/WM85B
Ventilation
” Contact Samsung Customer Service Centre for further details.
Installation on a perpendicular wall
A Minimum 15 mm
B Ambient temperature: 35 °C or less

Installation on an indented wall
A Minimum 15 mm
B Minimum 25 mm
C Ambient temperature: 35 °C or less
When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 °C.

Installing the wall mount
Using the wall mount kit

• The wall mount kit allows you to mount the product on the wall.
• For detailed information on installing the wall mount, see the instructions provided with the wall mount.
• We recommend you contact a technician for assistance when installing the wall mount bracket.
• Samsung is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.

Using the wall mount adapter (WM75B only)
Install the provided wall mount adpaters as shown in the figure below before installing the wall mount kit.
If you are installing a third-party wall mount, note that the length of the screws you can use to attach the product to the wall mount is shown in column C in the table on the next page.

Wall mount kit specifications (VESA)
” Install your wall mount on a solid wall perpendicular to the floor. To install the product on the other wall area, contact the nearest agency.
If you install the product on a slanted wall, it may fall and result in severe personal injury.

• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications.
• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions.
• Always have at least two people mount the product on a wall. (Four or more people for the 85-inch size and larger models.)
• Standard dimensions for wall mount kits are shown in the table below.
  Model name| VESA screw hole specs (A x B) in millimetres| C (mm)| Standard screw| Quantity
  ---|---|---|---|---
  WM55B| 400 x 400| 30 – 31| M8| 4
  WM65B| 32 – 33
  WM75B| 30 – 31
  WM85B| 600 x 400| 37 – 38

Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.

Connecting to a network
Connecting parts may differ in different products.

Network settings (Wired)
Connecting to a wired network
There are three ways to attach your product to your LAN using cable.

• You can attach your product to your LAN by connecting the LAN port on the back of your product to an external modem using a LAN cable. See the diagram below.
  

• You can attach your product to your LAN by connecting the LAN port on the back of your product to an IP sharer which is connected to an external modem. Use LAN cable for the connection. See the diagram below.
  

• Depending on how your network is configured, you may be able to attach your product to your LAN by connecting the LAN port on the back of your product directly to a network wall outlet using a LAN cable.
  See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in your house.
  If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS  values your product needs to access the Internet so you do not have to enter them manually. Most home networks are Dynamic Networks.
  Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen when you set up the network connection. To get  the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
  If you have a Windows computer, you can also get these values through your computer.
  You can use ADSL modems that support DHCP if your network requires a Static IP address.
  ADSL modems that support DHCP also let you use Static IP addresses.

Set the network connection to use Internet services such as perform software upgrades.

Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically

1. Set Network Type to Wired from the Open Network Settings page.
2. The network connection screen appears, and the verification process starts.
3. When the connection has been verified, the OK button appears on the bottom of the screen.
4. Tap OK.
   If the connection process fails, check the LAN port connection.
   If the automatic process cannot find the network connection values or if you want to set the connection manually, go to the next section, “Manual Open Network Settings (Wired)”.

Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway
and DNS server address. Enter these values manually.
Getting the network connection values
To view the Network connection values on most Windows computers, follow these steps.

1. Right click the Network icon on the bottom right of the screen.
2. In the pop-up menu that appears, click Status.
3. On the dialog that appears, click the Support tab.
4. On the Support tab, click the Details button. The Network connection values are displayed.

How to set up manually

1. Set Network Type to Wired from the Open Network Settings page.

2. The network connection screen appears, and the verification process starts.

3. Select Cancel while network connections are being attempted. This will stop the connection.

4. Select IP Settings on network connection screen. The IP Settings screen appears.

5. Select the field at the top and then set IP setting to Enter manually.
   Setting IP setting to Enter manually automatically changes DNS setting to Enter manually.

6. Enter the IP Address, Subnet mask, Gateway, and DNS Server values manually.

7. When done, select OK at the bottom of the page. The network test screen appears and the verification process starts.

8. When the connection has been verified, the OK button appears on the bottom of the screen.

9. Tap OK to complete the setting.

Network settings (Wireless)
Connecting to a wireless network

Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video may not play smoothly.
Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the wireless IP sharer is currently being used by another device nearby, this will result in interference and communication failure.
Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the encryption type is set to WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a connection in compliance with new Wi-Fi  certification specifications.
If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure the SSID and WPA key in either mode.
Connection methods: You can setup the wireless network connection in three ways. Auto Setup (Using the Auto Network Search function), Manual Setup, Use WPS
This product supports Enterprise WPA2 (TLS/TTLS/PEAP).

Automatic network setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Security Key. The Security Key is based on a Pass Phrase, typically a word or a series of letters and  numbers of a specified length you were asked to enter when you set up security for your wireless network.
If you use this method of setting up the network connection, and have a Security Key for your wireless network, you will have to enter the Pass Phrase during the automatic or manual setup process.

How to set up automatically

1. Set Network Type to Wireless from the Open Network Settings page.

2. The product searches for available wireless networks. When done, it displays a list of the available networks.

3. In the list of networks, select a network.
   If the desired wireless router does not appear, select Refresh to search again.
   If the router cannot be found after retrying, select Add Network.

4. If you selected a password-protected network, enter the password, and tap Go.
   You may skip this step if you selected an open network.

5. The network connection screen appears, and the verification process starts.

6. When the connection has been verified, the OK button appears on the bottom of the screen.

7. Tap OK.

Manual network setup (Wireless)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server address. Enter these values manually.
Getting the network connection values
To view the network connection values on most Windows computers, follow these steps.

1. Right click the Network icon on the bottom right of the screen.
2. In the pop-up menu that appears, click Status.
3. On the dialog that appears, click the Support tab.
4. On the Support tab, click the Details button. The Network connection values are displayed.

How to set up manually

1. Set Network Type to Wireless from the Open Network Settings page.

2. The product searches for available wireless networks. When done, it displays a list of the available networks.

3. In the list of networks, select a network.
   If the desired wireless router does not appear, select Refresh to search again.
   If the router cannot be found after retrying, select Add Network.

4. If you selected a password-protected network, enter the password, and tap Go.
   You may skip this step if you selected an open network.

5. The network connection screen appears, and the verification process starts.

6. Select Cancel while network connections are being attempted. This will stop the connection.

7. Select IP Settings on network connection screen. The IP Settings screen appears.

8. Select the field at the top and then set IP setting to Enter manually.
   Changing IP setting to Enter manually automatically changes DNS setting to Enter manually.

9. Enter the IP Address, Subnet mask, Gateway, and DNS Server values manually.

10. When done, select OK at the bottom of the page. The network test screen appears, and the verification process starts.

11. When the connection has been verified, the OK button appears on the bottom of the screen.

12. Tap OK to complete the setting.

How to set up using the WPS button
If your router has a WPS button, follow these steps.

1. Set Network Type to Wireless from the Open Network Settings page.
2. Select Use WPS.
3. Press the WPS or PBC button on your wireless router within the next two minutes. Your product automatically acquires all the network setting values it needs and connects to your network.
4. The network connection screen appears, and network setup is done.

Chapter 03 Writing

What’s a ‘Roll’?
• Files are called ‘rolls’ in this product. A ‘roll’ is a file with multiple pages linked together.
• A roll can have up to 20 pages linked together.
BRUSH MODE supports one page only.
You can open only one roll on one screen. For more information, refer to “Menu”.

Pen Mode
Screen elements

• IMPORT: View the screen of a mobile device or PC connected to the product, or import data such as  images from a connected USB or network drive.
• EXPORT: Share your creations in various ways.
2.  Pen Mode| Tap to select a mode. You can select from PEN MODE or BRUSH MODE.
3. Palette| Tap to open the Palette. You can select the colour and thickness of the pen and the highlighter.
4. Maths Tools| Use math tools to make geometric constructions and take measurements.
5. Select| Select the area you want to edit, capture, send in an email, print, or search.
 6. Undo
Redo| Undo or redo the last action.
• If any page editing actions such as page adding, deleting, and moving are found, /   is reset.
 can be performed up to 20 times for each individual.
7. Pages| You can add or delete a page, and you can also navigate through pages on the current roll.
8. Note On/Off| Create a layer to write or draw on over the screen which can also be saved the captured image.
9. Miniboard| Bring out Miniboard to take notes or draw as a separate layer above the viewer or source screen.
10. Search| Tap to search the Internet.
11. Menu| Tap to see more options available in the menu.
12. | Close the current roll and create a new roll.
13. Page breaking line| See page lines.
14. | Scroll through pages.
15 Bezel Scroll| Scroll the black area to move the pages.

Drawing
You can freely use the supplied pen to write anything you want.

• Thin Tip ( A ): Pen Type

• Thick Tip ( B ): Highlighter Type

• When you are using the thin tip, if the pen is tilted too much toward the screen (within 45 degrees as shown in the figure), the output can appear to be highlighter type.

Erasing
You can use your finger or palm to erase your writing.

Using the simple menu
With long presses everywhere, you can quickly access simple menu.

Brush Mode
Screen elements

• IMPORT: View the screen of a mobile device or PC connected to the product, or import data such as images  from a connected USB or network drive.
• EXPORT: Share your creations in various ways.
2. Brush Mode| Tap to select a mode. You can select from PEN MODE or BRUSH MODE.
3. Palette| Tap to open the Palette. You can select the colour and use other options.
• : Dry colours to stop blending.
• : Extract the colour from the selected point.
• : Delete the selected area.
4. Select| Select the area you want to capture, send in an email, or print.
5. Undo Redo| Undo or redo the last action.
• If any page editing actions such as page adding, deleting, and moving are found, /   is reset.
can be performed up to 5 times for each individual.
6. Menu| Tap to see more options available in the menu.
7. | Close the current roll and create a new roll.

Changes in the thickness depending on the area touching the screen apply immediately. (max. 5.0 cm)
Brush use is recommended.
BRUSH MODE supports single touch only.
The product can distinguish 2048 levels of thickness in BRUSH MODE.

Menu

This menu is only visible in PEN MODE.
ROLL LOCK / UNLOCK| • ROLL LOCK: Press a six-digit password to lock the current roll.
• UNLOCK: To unlock a locked roll, press the six-digit password you set when locking the roll.
Once unlocked, the current roll remains unlocked until it is locked again.
SETTINGS| You can see the configuration menu.
HOW TO USE| You can see How To Use.

Roll Browser

• All / Pen Mode / Brush Mode
2. By date By name| Set the sort order of files.
• By date: The rolls are sorted by recent date. This is the default sort option.
• By name: The rolls are sorted by name of the rolls.
3. Edit| Select multiple rolls to export or delete.
4. Close| Close Roll Browser.
5. File name| Rename the file.
6. Rolls| Browse and open a desired roll.

To open a locked roll ( ), press the six-digit password.

Deleting / Exporting rolls

Email (@) / USB ( ) / Network Drive ( )
2 Delete| Delete the selected rolls.
3 Cancel| Deselect the roll.

Page Viewer

The displayed image may differ depending on the model.

This menu is only visible in PEN MODE.

• When you tap a page, the focus is moved to it.
3 | Delete the focused page.
4 | Add a new page.
You can create up to 20 pages per roll.

Note On/Off

This menu is only visible in PEN MODE.

underneath.
3 Save| You can save the note as a captured image.
4 Close| You can close the note.

Using the Select tools

Search / Capture / Email / Print

1. Tap in the tool menu. A select box appears on the screen.
   Drag the A of the select box to adjust the size.

2. Select the area and choose from / / / options.
   The product must be connected to a network to use the Search, Email or Print function.
   The Search function is only available for handwriting.

Editing the selected content
” The editing function is only available in PEN MODE.

1. Tap in the tool menu. A select box appears on the screen.
    Drag the A of the select box to adjust the size.

2. Tap to enable editing for the selected area.

3. Move, rotate or resize the selected area and tap .
   Tap to abort the changes.

Chapter 04 IMPORT

You can view the screen of a mobile device or PC connected to the product, or import data such as images from a connected USB or network drive.

• Tap on the left or right side of the screen to open the IMPORT/EXPORT window. Then, tap IMPORT to select the desired device.
  

Mirroring function.
| Displays your PC screen using HDMI, DisplayPort, USB-C, OPS connection or Wireless Display.
” OPS is only available for WM75B/WM85B.
| You can display the screen shared from your PC, mobile, or tablet.
| Connect the network to access the Internet from the product like accessing the Internet from a computer.
| Access to remote PC and your work resources with this function.
| You can view all content (on this device or a connected USB storage or network drive) or download  files from the Internet.

The native FLIP format (.iwb) refers to files that are directly saved from the device and only supported by FLIP devices.
Supported video file formats: avi, mkv, asf, wmv, .mp4, mov, 3gp, vro, mpg, mpeg, ts, tp, trp, flv, vob, svi, m2ts, mts, .webm, .rmvb
Supportable image file formats: JPG, BMP, PNG, MPO
Supported document file formats: DOC, PPT, PDF, XLS

Connecting to a mobile device

→ IMPORT → MOBILE

Connecting using Smart View or Screen Mirroring

1. Drag down the top bar on the mobile device screen to start Smart View or Screen Mirroring.
2. Select this product from the list of devices displayed on the screen.
   – The initial device name is [CLASS] Interactive Signage Flip.
   You can control the mobile device from the product screen.
   HDCP (High-bandwidth Digital Content Protection) contents will not show on the screen if PIP Capture is set to On.

Connecting to a PC

Connecting using a cable
” Connecting parts may differ depending on the model.

1. Connect the product to the PC using an HDMI, DP, and USB-C cable.
   HDCP contents will not show on the screen if PIP Capture is set to On.
   When the screen is black, turn off PIP Capture because some graphic cards can support HDCP automatically.
   Use a USB-C cable that is 1 m or shorter in length.
   Charging with USB-C cable is only available when the product is on.
   < WM55B/WM65B>
   You must use a USB-C cable that supports video transmission. Use a cable that supports DP ALT Mode (Video transmission).
   Charing is also supported up to 15 W (5 V/max 3 A). Charging with USB-C cable is only available when the product is on.
   < WM75B/WM85B>
   You must use a USB-C cable that supports video transmission and charging function.
   Use a cable that supports DP ALT Mode (Video transmission) and Power Delivery (65 W or higher).
   Charging with USB-C cable is only available when the product is on.
   

2. Select → IMPORT → PC → HDMI / DisplayPort / USB-C on the screen.

3. To control the PC from the product screen, connect the supplied USB cable to the TOUCH port on the product.
   If used in a multi-screen setup, make sure you have configured FLIP as the main display.
   This step does not apply if you are using a USB-C cable.
   If you use Mac OS, you must install the UPDD driver to control your PC. You can download the UPDD driver from https://displaysolutions.samsung.com/support/resources/product-support.
   If you are using MAC with macOS 11 (Big Sur) and over, go to System Preference, click Security & Privacy, then select App Store and identified developers under the header Allow apps downloaded from.
   

Connecting using a OPS (Sold separately)
OPS is only available for WM75B/WM85B.

Touchscreen may not work properly during initial OPS Windows settings. Connect a mouse and keyboard to OPS for use during initial settings.
Turn off Flip before connecting OPS.

Connecting via the Wireless Display function

1. Select Action Center or Devices in the taskbar notification area of the laptop.
2. Click Connect or Project and select a [CLASS] Interactive Signage Flip device to complete the connection.
   The connection procedure may vary depending on the laptop.
   After the Wireless Display connection is made, you can control the laptop screen from the product screen.
   This function is only supported by Windows 8.1 and 10.

Connecting via SMARTVIEW+

You can display the screen shared from your PC, mobile, or tablet.
Make sure that your PC, mobile, and tablet are connected to the same network as Flip.

1. Select SMARTVIEW+.
2. Once SMARTVIEW+ starts, follow the onscreen instruction to connect with the desired device.
   The CA certificate installation is required for the PC Client, and you can download the CA certificate from the URL provided in the initial screen of SMARTVIEW+.
   You may get a security warning if you try to access Flip SMARTVIEW+ on your PC client browser without the CA certificate installed. Click ‘Advanced’ on the browser to advance to the site, and you can install the CA certificate. (This instruction may not  apply to all the browsers.)
   If the Client device’s screen aspect ratio differs from the Flip, the Client device may transmit a partially cropped screen. You may experience a partially cropped image of the Client device’s screen on Flip since it displays according to the signal received  from the Client device.
   SMARTVIEW+ supports the following browsers; however, browsers on some devices may not work normally.
   – Web Browser: Chrome 72 above, Safari 13 above, Edge 79 above, FireFox 66 above
   – PC: Windows, Mac OS, ChromeOS
   – We recommend the following for optimized screen sharing with SMARTVIEW+:
   • Use the Firefox browser.
   • Set the client device’s screen aspect ratio and the screen orientation the same as the Flip. (Example: PC – Landscape, Flip – Landscape)
   You can download and install the SAMSUNG SIGNAGE MOBILE app (Samsung Flip) from the Play Store, App Store, and Galaxy Store.
   – Mobile: iOS(12 above), Android(9 above)
   After connecting the client device to Flip, you must choose a sharing option from the full screen, app screen, or browser tab to start sharing your screen.

Connecting to Internet
→ IMPORT → INTERNET
Connect the network to access the Internet from the product like accessing the Internet from
a computer.
Capture, reposition, or see the browser window in full screen view.
A specific page may not appear or work due to compatibility issues.

Read before using the INTERNET function
Read this information before using the INTERNET function.

• File download and upload is supported.
• The INTERNET function may not be able to access certain websites, including websites operated by certain companies.
• Flip does not support playback of flash videos.
• E-commerce for online purchases is not supported.
• ActiveX is not supported.
• Only a limited number of fonts are supported. Certain symbols and characters may not be displayed properly.
• The response to remote commands and the resulting on-screen display may be delayed while a web page is loading.
• Loading a web page may be delayed or suspended completely depending on the status of the participating systems.
• Copy and paste operations are not supported.
• When composing an email or a simple message, certain functions such as the font size and color selection may not be available.
• There is a limit to the number of bookmarks and the size of the log file that can be saved.
• The number of windows that can be opened concurrently is limited.
• Web browsing speed will differ with the network environment.
• Browsing history is saved from latest to oldest, with the oldest entries being overwritten first.
• Depending on the types of video/audio codecs supported, you may not be able to play certain HTML5 video and audio files.
• Video sources from PC-optimized streaming service providers may not play properly on our proprietary INTERNET browser.

Connecting to WORKSPACE

• Windows PC
  – Remote PC: This function allows you to connect your product to a remote PC or a cloud server.
  Only PCs or Cloud Servers running on macOS/Windows 7 Pro or newer are supported.

• Mac
  – Remote Login: Connect to Your Mac via Remote Login

• Microsoft 365: Provides access to Microsoft 365 features from Microsoft.

• VMware Horizon: Enterprise customers with VMware infrastructure can access VMware Horizon.

• Network Drive: Connect the network drive to bring files.
  You can register a network drive while the network is connected.
  For information about how to connect to a network, see “Connecting to a network”.
  You can register a network drive account at Menu → SETTINGS → Connect →
  Advanced Settings → Network Drive → Add Account.
  To register a network drive account, you must enter the Address, Username, and Password.
  To register your network drive account, refer to “Add Account” for Network Drive.
  Import videos, images, native FLIP files (.iwb), or document files.

• Google Duo: You can use this app to start a video calling with up to 32 participants.
  A camera connection is required to use this app.

Importing from a USB device

The contents displayed on your product screen may differ from the above image.
Connect an external HDD or a USB storage device.
Import videos, images, native FLIP files (.iwb), or document files.

Source window

When you connect a PC or a mobile device to the product, the source window appears.

desired position.
2| Device name / Source port| Displays the name of the connected device or source port.
3|  Volume| Adjust the volume.
4| Freeze Frame| Pause the input screen display.
This feature is not available when you connect to the product via SMARTVIEW or SCREEN SHARE.
5|  Capture| Capture the source window.
This feature is not available when PIP Capture is set to Off.
6|  Rotate| Rotate the source window.
This function is supported only on Android 8.0 Oreo version or later of Samsung mobile devices.
7| Maximize| You can view the input source on full screen.
8|  Close| Close the viewer.
9| | Adjust the size of the source window.

Document view

Displays the document file you select to import from a File Browser or network drive.
Supported document file formats: DOC, PPT, PDF, XLS

position.
2| File name| Name of the currently viewing file.
3|  Volume| Adjust the volume.
4|  Capture| Capture the document viewer screen.
This feature is not available when PIP Capture is set to Off.
5|  Maximize| You can view the document on full screen.
6|  Close| Close the viewer.
7| | Tap  to move between pages.
8| | Adjust size of the viewer.

Image view

Select the file to import from the File Browser or network drive.

position.
2| File name| Name of the currently viewing file.
3|  Capture| Capture the image viewer screen.
4|  Merge Image| Tap to paste the image to the roll.
5|  Rotate| Rotate the image.
6|  Maximize| You can view the image on full screen.
7|  Close| Close the viewer.
8| | Adjust size of the viewer.

Video view

Select the video file to import from a File Browser or network device and display.
Supported video file formats: avi, mkv, asf, wmv, .mp4, mov, 3gp, vro, mpg, mpeg, ts, tp, trp, flv, vob, svi, m2ts, mts, .webm, .rmvb

position.
2| File name| Name of the currently viewing file.
3|  Volume| Adjust the volume.
4|  Rotate| Rotate the video screen.
5|  Maximize| You can view the video on full screen.
6|  Close| Close the viewer.
7| | Play or pause the video.
8| Playback slider and time details| Navigate through the video and view time details for the file.
9| | Adjust size of the viewer.

Chapter 05 EXPORT

You can export your created rolls in various ways.

• Tap on the left or right side of the screen to open the IMPORT/EXPORT window. Then, tap EXPORT to select the desired menu.
  BLOCK SCREEN: You can hide the Flip screen for a while with BLOCK SCREEN. To return to the previous screen, press the Power button. Icons| Description
  ---|---
  @| Send your created rolls via email.
  | Print your created rolls.
  | Export your created rolls to a connected USB device.
  | Export your created rolls to a registered and connected network drive.
  | Send the roll to a mobile device.
  | Share your screen with selected devices.

Sending email

To send your created rolls via email, first register your email account.
You can register your email account at Menu → SETTINGS → Connect → Advanced Settings → Email.
If you set Sender Authentication to Personal Account at Menu → SETTINGS → Connect → Advanced Settings → Email, you must authenticate your account each time you send an email. See below.
– You can send emails when Sender Authentication is set to Personal Account as long as you have an account on that mail server (SMTP Server Name and SMTP Port Number).
Note that it requires the sender to provide the SMTP account ID and password, as well as the sender address for every email.
– If you set Sender Authentication to Default Account, you can use the SMTP ID and password you saved to Default Account to send emails. (The sender address is usually identical to the SMTP ID, with some exceptions depending on the SMTP server.)
– For the SMTP information required to register a mail server, contact your mail server administrator.
Files saved as dedicated files are converted to PDF files and sent.

current date.
2| To| Enter the recipient’s email address.
• Press  and type text by using the virtual keyboard.
Press on the virtual keyboard to enter text by handwriting.
Search recipient in Local Address Book or LDAP server.
3| | Select the pages to send.
4| Send| Send the email.
5| Cancel| Tap to cancel sending an email.

Printing
To print, you must set up the Print Server and the Clock Set.
To set up the Print Server, the product and the printer you want and your PC must be connected to the same network.
Flip Printing Software must be also installed on the PC connected.
For information about how to connect to a network, see “Connecting to a network”.
You can set up the Print Server at Menu → SETTINGS → Connect → Advanced Settings → Print Server.
You can set Clock Set at Menu → SETTINGS → System → Time → Clock Set.
The Flip Printing Software is available on the website
– http://displaysolutions.samsung.com
– http://www.samsung.com
Devices that transfer files, such as virtual printers (PDF, XPS, One note, etc.) or fax machines, are not supported, but only printers that can print actual paper are supported.
For print paper size, only A4 is supported.

Installing Flip Printing Software
Follow the onscreen instructions to install Flip Printing Software.
The installation takes about 10 minutes, and the time taken may vary depending on your PC environment.

PC installation requirements

• Supported operating systems:
  Windows 7(32/64 bit), Windows 10(32/64 bit), MAC
  When installing the software, make sure that critical Windows updates are already installed. Update Windows to the latest version before beginning the setup.
  For Windows 7, make sure that Service Pack 1 is already installed.

Setting up the printer
After the Flip Printing Software is installed, make the following settings on the product onscreen menu.

Setting up automatically

1. Select Menu → SETTINGS → Connect → Advanced Settings menu.
2. Select Print Server → Connect to Server → Auto.

Setting up manually

1. Select Menu → SETTINGS → Connect → Advanced Settings menu.
2. Select Print Server → Connect to Server → Manual, and then enter the Server IP address and the Server Port number of the PC where Flip Printing Software is installed.

the roll with.
2| Copies| Set the number of prints.
3| Print preview area| Preview the roll to print.
4| Print| Start the printing.
5| Colour Mode| Select the colour to print the roll with.
6| | Change the page view mode of the roll to print.
7| | Select the pages to print.

Exporting to a USB device

The contents displayed on your product screen may differ from the above image.
Connect an external HDD or a USB storage device.
Your device saves files in two versions (IWB and PDF formats).

Exporting from a Network Drive

Connect the network drive to save files.
You can register a network drive while the network is connected.
For information about how to connect to a network, see “Connecting to a network”.
You can register a network drive account at Menu → SETTINGS → Connect → Advanced Settings → Network Drive → Add Account.
To register a network drive account, you must enter the Address, Username, and Password.
To register your network drive account, refer to “Add Account” for Network Drive.
Your device saves files in two versions (IWB and PDF formats).

Sending to a mobile device

→ EXPORT → MOBILE
View the screen of the product from a mobile device.
Sharing is only available for rolls at the moment.
Download the SAMSUNG SIGNAGE MOBILE app after searching from Play Store or Galaxy store to your mobile device and enter the following information which can be found on the product screen.

• Versions supported: iOS(12 or above), Android(9.0 or above)
• QR code, Wi-Fi Name, Wi-Fi Password, Server IP address

Sharing your screen

Share your screen with selected devices.

Connecting wirelessly
Select   → EXPORT → SCREEN SHARE → Wireless on the screen and then the device to share the screen with.
SCREEN SHARE feature works best when using FLIP in landscape orientation.
Devices must support receiving Screen Mirroring to project the shared screen using SCREEN SHARE.

Chapter 06 SETTINGS

→ SETTINGS

Connect

the factory default.
| Input Device Manager| Setup up input devices (keyboard or mouse) to use with your display device. You can add input devices and configure settings.
• Bluetooth Device List
• Keyboard Settings
• Mouse Settings
Device Connection Manager| Allow devices on your network, like smartphones and tablets, to share content with your product.
• Access Notification
• Device List
Anynet+ (HDMI-CEC)| Activate or deactivate HDMI-CEC.

Anynet+ (HDMI-CEC)
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung  device has this feature, check if there is an Anynet+ logo on it.

• You can only control Anynet+ devices using the product remote control, not the buttons on the product.
• The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
• Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
• While in PIP mode, Anynet+ functions only when an AV device is connected as the primary display. It does not work if the AV device is connected as a secondary display.
• Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.

This is the name that will appear on mobile devices and computers connected to your network.
Apple AirPlay Settings| | Use AirPlay to effortlessly stream videos, music, and photos from your iPhone, iPad, or Mac to Flip.
Advanced Settings| Email| Set up an email account for sending emails.
• SMTP Server Name: SMTP server address
• SMTP Port Number: SMTP server port
• SSL/TLS: Enable or disable SSL/TLS
• Sender Authentication: Choose the authentication mode to be used when sending emails
– Personal Account / Default Account / Personal (LDAP) Account
• Default Account: Default SMTP account
• Password: Password for the default SMTP account
• Sender Email: Sender’s email address
• Recipient Address: Select from options to manage email contacts after successfully send emails
– Auto Save / Do Not Save / Delete All
• Local Address Book: Import contacts from a USB device or delete them.
– Import / Delete
For more information, refer to “Importing Local Address Book contacts”.

Local Address Book
Importing Local Address Book contacts

To use FLIP Local Address Book, first import contacts from a CSV file using a USB device.

1. Use LDAP: Set Don’t Use.
   Menu → SETTINGS → Connect → Advanced Settings → Enter password → LDAP → Set LDAP Connection → Use LDAP → Don’t Use

2.  Set up details under Email menu.
   Menu → SETTINGS → Connect → Advanced Settings → Enter password → Email

3. Edit and save your Local Address Book to a USB device.
   Make a list of contacts in the following structure and save it to the root directory as RecentSearchList.csv.
   – RecentSearchList.csv structure (example)emailid1@samsung.com | Name1| Level1| Team1| Company1
   ---|---|---|---|---
   emailid2@samsung.com | Name2| Level2| Team2| Company2
   emailid3@samsung.com | Name3| Level3| Team3| Company3

4. Connect the USB device to FLIP to import contacts.
   Menu → SETTINGS → Connect → Advanced Settings → Enter password → Email → Local Address Book → Import
     The USB device and its contents may not be detected properly if a USB extension cable is used. (USB hubs are not supported.)
     Do not remove the USB device while loading.
   If more than two USB devices are connected, some of them may not be detected.
   USB devices that require higher operating power need to be connected to the USB (1A) port on the back.
   The file system supports FAT, exFAT, and NTFS formats.

Using Local Address Book contacts
Automatically search and suggest from the list of contacts when selecting recipient(s) in
→ EXPORT → EMAIL.
To use this function, complete setting details under Email menu.
Deleting Local Address Book contacts
Menu → SETTINGS → Connect → Advanced Settings → Enter password → Email → Local Address Book → Delete

function.
For more information, refer to “Printing”.
• Connect to Server
– Auto: View and select one from a list of server IP addresses of the PCs where Flip Printing Software is installed, available on the network.
– Manual: Enter the Server IP address and Server Port number of the PC where Flip Printing Software is installed.
• Server IP: Enter the Server IP address of the PC where Flip Printing Software is installed.
• Server Port: Enter the Server Port number of the PC where Flip Printing Software is installed.
| Network Drive| Add or edit network drive accounts. If you cannot connect to the network drive, update SAMBA of PC to the latest version.
• Add Account: Add new network drive accounts. Only Samba can be added to the network drive.
SAMBA 2.0 or later is supported. If you cannot connect to the network drive, update SAMBA to the latest version.
To register a network drive account, you must enter the Address, Username, and Password.
– Address: //computer IP address/shared folder name
When entering an address, be sure to use / instead of ₩ and \.
For example, if you share a folder named “sharedfolder” on a PC with IP address of 12.34.56.789, enter
//12.34.56.789/sharedfolder” as the address.
– Username: A Windows account with permissions to the shared folder
  When entering a domain, be sure to use ₩ or \.
For example, DomainName₩WindowsAccount
– Password: The password you set for your Windows account
• Edit Account: Edit network drive accounts.
2nd| 3rd| Description
---|---|---
Advanced Settings| LDAP| Set LDAP connection or configure connected LDAP queries.
• Set LDAP Connection
Configure a new LDAP connection.
– Use LDAP: Whether or not to use LDAP
– Import Setup Value: Can fetch the following settings from LDAPConnectionConfig.txt stored on the USB (Password excluded)
For more information, refer to “How to create a text file for use of LDAP”.
– Authentication Type: Kerberos, Anonymous or Basic whichever is supported by the LDAP server
– User ID: DN(Distinguished Name) of User ID that is used in the LDAP server
The format of User ID complies with the DN format of LDAP.
e.g. cn=admin, dc=myldap, dc=com
– Password: Password that is used for authentication of the LDAP server
– Server Address: IP or URL of the LDAP server
– Server Port Number: Port number of the LDAP server
– Base DN: Base DN that is to be used for search in the DIT(Directory Information Tree) when connecting LDAP
– SSL/TLS: Whether or not to use SSL/TLS
  When SSL/TLS is set to be Use, the encrypted data communication is enabled.
– Use Untrusted Certificates: Whether or not to allow untrusted certificates
The following menu is activated when setting Authentication Type to Kerberos.
Kerberos Realm: Kerberos realm data
KDC Host: KDC Host URL
KDC Port: KDC Host port number
2nd| 3rd| Description
---|---|---
Advanced Settings| LDAP| • LDAP Query Configuration
Set the query for the connected LDAP.
– UID: Change the user UID that is used in LDAP.
– Email: Change the Email that is used in LDAP.
– Name: Change the user name (common name) that is used in LDAP.
– Last Name: Change the surname of the user that is used in LDAP.
– Position: Change the title that is used in LDAP.
– Company name: Change the company name that is used in LDAP.
– Department: Change the department name that is used in LDAP.
– Use Custom Query: Fetches the user defined query from LDAPQuery.txt (case sensitive) stored on the USB.
For more information, refer to “How to create a text file for use of LDAP”.
When the mapping does not match, the search result does not include the attributes.
| Server Network Settings| Set up your server network connection and related functions.
• Connect to server: Connect to MagicInfo server.
• Server Access: Allow or deny access to MagicInfo server.
• Proxy server: Set up your proxy server connection and related functions.
| Certificate Manager| Manage the certificate files for this device.
• App Certificate: View and manage the app certificates installed on this device. Connect a USB flash drive that contains certificates to install them on this device.
• Wi-Fi Certificate: Manage the certificates installed on this device. Connect a USB flash drive that contains certificates to install them on this device.

How to create a text file for use of LDAP
The LDAP configuration basically consists of many long sentences.
During LDAP configuration, FLIP can be fetched using the text file to prevent typos and make a batch setting.
Input of file name and content should be case sensitive for correct operation.
• Format of LDAPConnectionConfig.txt

1. Example of the text file
   User ID=cn=Manager, dc=example, dc=com
   Server Address=123.456.789.012
   Server Port Number=12345
   Base DN=dc=samsung, dc=example, dc=com
   SSL/TLS=Don’t Use
   Use Untrusted Certificates=Don’t Use
   Authentication Type=Basic
   Kerberos Realm=MYLDAP.COM
   KDC Host=krb1.myldap.com
   KDC Port=88

2. Allocation of values (VAL) for each key
   User ID: Enter User ID.
   Server Address: Enter the IP or URL of the LDAP server.
   Server Port Number: Enter the Port of the LDAP server.
   SSL/TLS: Enter Use or Don’t Use.
   Use Untrusted Certificates: Enter Use or Don’t Use.
   Authentication Type: Enter Basic or Anonymous.
   – The following three items will be added if you select Kerberos type verification.
   Kerberos Realm: Fill in the Kerberos field (Example: MYLDAP.LDAP)
   KDC Host: Enter the KDC Host URL (Example: krb1.myldap.com)
   KDC Port: Enter the KDC Host Port (Example: 88)
     If you select to use Kerberos type verification, use the original Kerberos User ID for a User ID instead of User ID in DN(Distinguished Name) format. (Example: Mirko)

• Format of LDAPQuery.txt

1. Example of the text file
   UID=uid
   Email=mail
   Name=cn
   Last Name=sn
   Position=title
   Company Name=o
   Department=departmentNumber
   Query=(|(mail=)(cn=))

2.  Allocation of values (VAL) for each key

1. Mapping part (all rows except the last)
   – Includes all rows except the last, in the order of UID, Email, Name, Last Name, Position, Company name, and Department.
   – Values are mapped in the following manner.
   On the left of “=” syntax is the name that is seen in the LDAP Query Configuration menu (also on the left) and mapped to the values on the right side of “=” (the actual LDAP Server attributes).
   – You can choose attributes to change values. For instance, you can change the right-side values without changing the left-side values.
2. Query part
   – is the Keyword that is used for a Search.
   – The syntax for the Use Custom Query complies with the LDAP Query rule excluding .
   For example, when is included in the mail or cn attribute, you can create it as follows.
   Query=(|(mail=)(cn=))

Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu. For information on the Open Source Licence Notice, contact Samsung Open Source (http://opensource.samsung.com).

References

• US | Business Solutions, Services and Technology from Samsung
• Samsung US | Mobile | TV | Home Electronics | Home Appliances | Samsung US
• Samsung India | Mobile | TV | Home Appliances
• US | Business Solutions, Services and Technology from Samsung

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>