i sears Toilet Bowel Pipe High Tank Toilet User Manual
- June 2, 2024
- i sears
Table of Contents
i sears Toilet Bowel Pipe High Tank Toilet
Specifications
| Feature | Description |
|---|---|
| Product Type | High Tank Toilet |
| Pipe Type | “L” Pipe |
| Mount Type | Wooden Pull Chain |
FAQ
- Q: What should I do if the water leaks after installation?
- A: Ensure all connections are tight and squarely aligned, and double-check that the rubber gasket and washers are properly seated. If the leak persists, disassemble the affected area, check for damage to components, and reassemble with new parts if necessary.
- Q: Can I install this toilet if I don’t have studs in the wall?
- A: If studs are not accessible, you can install a wood backing between the studs to provide a secure material to mount the moulding bracket.
- Q: How do I adjust the water level in the tank?
- A: Water level is pre-adjusted from the factory but may need to be re-adjusted. Consult the manufacturer’s instructions for adjusting the water level.
- Q: What cleaning agents are safe to use on this toilet?
- A: Avoid using abrasives, detergent, or acids as they can damage the unit and void the warranty. Use mild cleaning agents and a soft cloth for cleaning.
Preparation and Disassembly
- Shut off the water supply to the existing toilet
- Disconnect the water supply tubing from the existing tank and angle stop valve
- Remove existing toilet and tank from the floor
- Remove old wax seal and clean area around the drain
- Draw a line from the centre of the drain to the wall. Continue the line up the wall and draw a horizontal line at 60 inches. (this marks the moulding bracket position
Installation
- urn toilet bowl upside-down. Place a new wax (remove any paper cover) ring and sleeve over the drain horn. Press down firmly. (FIG 1)
- Make sure the toilet flange is clean and the bolts point straight up. carefully position the toilet bowl over the flange and align the floor bolts with the holes in the toilet base. (FIG 2)
- Press down on the toilet bowl to compress and create a tight seal. Attach washers and nuts to floor bolts and tighten. (use an adjustable, non-scratch wrench and do not over-tighten bolts). (FIG 3)
overview
| Part Letter | Part Description | QTY |
|---|---|---|
| A | Flush Arm | 1 |
| Al | Fill Valve | 1 |
| A2 | Flush Valve | 1 |
| A3 | Small Plastic Locknut (for Fill Valve) | 1 |
| A4 | Large Plastic Locknut (for Flush Valve) | 1 |
| AS | Rubber Fill Tube | 1 |
| A6 | Plastic Tank Liner | 1 |
| A7 | Wood Tank | 1 |
| B | Hanger Bracket | 2 |
| C | Pull Chain | 1 |
| D | Moulding Bracket | 1 |
| E | Coupler | 1 |
| G | 49″ Long Hard Flush Line | 1 |
| Gl | Donut Gasket | |
| J | Large Decorative Nut | 1 |
| K | Rubber Washer | 2 |
| L | ½” Dia. Hard Fill Line | 1 |
| N | Shut Off Valve | 1 |
| 0 | 12″ Flex Supply Line | 1 |
| p | Nipple | 1 |
| Q | Flange | 1 |
| s | Shook | 1 |
| 51 | Hook Screw (for Handle) | 1 |
| T | Bracket Screw | 2 |
| T2 | Moulding Bracket Screw | 7 |
| T3 | 5/5 Pin Head Screw | 6 |
| u | Bracket | 1 |
| V | Small Brass Decorative Nut | 1 |
| w | Cone Washer | 1 |
| X | Brass Cradle | 1 |
| y | Handle | 1 |
| Zl | Large Metal Locknut | 1 |
| Z2 | Large Rubber Gasket | 1 |
| Z3 | Small Rubber Gasket | 1 |
| ZS | Plastic Slip Joint Washer | 2 |
| Z6 | Brass Slip Joint Nut | 1 |
| Z7 | Rubber Water Restrictor | 1 |
INSTALLATION PROCEDURE
- Install toilet as per manufacturers’ instructions.
- Attach brass cradle (X) to the front right side of wood tank (A?) using two S/S pinhead screws (T3). Make sure the cradle is positioned over the inside of the tank. Using the S hook (S) attach the chain (C) to the right side of the flush arm (A). Attach handle (Y) to chain. (FIG 1
- Check and make sure the refill tube (A5) is inserted and securely connects the fill valve (A1) to the flush valve (A2) . Insert Fill Valve (A 1) and Flush Valve (A2) into the tank liner (A6) and secure using the provided plastic lock nuts (A3,A4). (FIG 2)
- To mount moulding bracket (D), locate the centerline on the wall behind the bowl and mark the tank height using the instructions on page 1 . We recommend that the bottom edge of the moulding bracket (D) be about 60 inches from the floor for a regular 16-inch toilet bowl. Secure moulding bracket (D) to studs with mounting screws (T2). If necessary, drill holes on the moulding bracket (D), make sure not to drill within 1 inch of the perimeter. This area will be exposed. (FIG 3) If studs are not accessible, a wood backing can be installed between the studs. The backing must be installed behind the finished wall to provide a secure material to mount the moulding bracket (D).
- Make sure the rubber doughnut gasket (G1) (in the rear port of the toilet bowl) is fully seated. Push/twist the bottom end of a flush pipe (G) into the donut gasket (G1) until pipe meets stop at the far end of the gasket (G 1) and is fully seated in the rear entry port of the toilet bowl. (FIG 4)
- Align hanger brackets (B) on the wood tank to the inside notch of the moulding bracket (D) and hang the wood tank (A7) onto the moulding bracket (D). (Fig 5)
- Slide brass slip joint nut (Z6) followed by plastic joint washer (Z5) and large decorative nut (J) with rubber washer (K) into the top end of the flush tube (G). Inset the rubber water restricter (Z7) inside a flush tube (G) and loosely attach the large decorative nut (J) to the receiving thread of the flush valve (A2) on the wood tank. Slightly Tighten all joints. (FIG 6)
- Install the nipple (P) to the water fitting from the wall. Make sure to wrap both sides of the nipple (P) with thread sealer. Slide the flange (Q) onto the nipple (P) and install the shut-off valve (N). (FIG 7)
- Slide the small decorative nut (V) from the opposite end of the fill line (L) (non collared end). Inset the cone washer (W) between the fill line (L) and the small decorative nut (V) and loosely attach the small decorative nut (V) to the receiving thread of the fill valve (A 1 ). (FIG 8) Slide bracket (U) onto fill line (L) and secure to wall using provided screws (T). Use the coupler (E) to connect the 12-inch flex line (0) to the fill line (L) and attach to the shut-off valve (N). (FIG 7) Tighten all connections with a wrench and make sure all connections are squarely aligned to ensure no leakage. Do a final check to make sure all connections are tight.
- Turn off the shut-off valve (N) and fill the tank to its waterline and test the flush system, checking for leaks. Water level is pre-adjusted from the factory and in some cases may need to be re-adjusted. CAUTION: Before turning on water please make sure all parts are secure and installed properly. Never use abrasives, detergent, or acids to clean the unit as they will damage the unit and void the warrenty.
PART
SUPPLEMENTAL PART IMAGES
Documents / Resources
| i
sears Toilet Bowel Pipe High Tank
Toilet
[pdf] User Manual
Toilet Bowel Pipe High Tank Toilet, Toilet, Bowel Pipe High Tank Toilet, Pipe
High Tank Toilet, High Tank Toilet, Tank Toilet
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>