cecotec 2000 ReadyWarm Max Force Instruction Manual
- June 17, 2024
- cecotec
Table of Contents
cecotec 2000 ReadyWarm Max Force
Product Information
Specifications
- Product Name: READYWARM 2000 MAX FORCE BLACK/WHITE
- Type: Termoventilador / Fan Heater
Product Usage Instructions
Parts and Components
The product consists of the following parts and components:
- Main unit (heater)
- Power cable
- Plug
- Control panel
- Thermostat
- Fan
- Heat settings controls
- Safety features (overheat protection, tip-over switch)
Before Use
Before using the product, please ensure the following:
- Check that the mains voltage matches the voltage specified on the device rating label.
- Ensure that the plug is properly grounded.
- Inspect the power cable for any visible damage. If damaged, contact the official Cecotec Technical Support Service for a replacement.
Place of Installation
The product should be installed in a location that meets the following requirements:
- Ensure that the power outlet is easily accessible.
- Do not install the heater as an embedded unit.
- Maintain appropriate safety distances as indicated in the user manual.
Operation
To operate the product, follow these steps:
- Plug the power cable into a suitable power outlet.
- Turn on the heater using the power switch or control panel.
- Adjust the heat settings using the controls provided.
- Set the desired temperature using the thermostat.
- The fan will distribute the heated air.
Preparing for Use
Prior to using the product, ensure the following:
- Place the heater on a stable and level surface.
- Keep flammable materials away from the heater.
- Ensure that there are no obstructions around the heater that could impede proper airflow.
Cleaning and Maintenance
To clean and maintain the product:
- Ensure that the product is turned off and unplugged from the power source.
- Use a soft cloth to wipe the exterior surfaces of the heater.
- Periodically remove dust and debris from the fan and heating elements using a vacuum cleaner or a soft brush.
Tips and Suggestions
Here are some tips and suggestions for optimal use:
- Place the heater in a central location for better heat distribution.
- Adjust the heat settings and thermostat according to your comfort level.
- Do not leave the heater unattended while in use.
Troubleshooting
If you encounter any issues with the product, refer to the troubleshooting section of the user manual or contact the official Cecotec Technical Support Service for assistance.
FAQ
-
Q: Can I use this heater in small rooms?
A: It is not recommended to use the heater in small rooms if the occupants are incapable of leaving by themselves, unless continuously supervised. -
Q: Can I use this heater in commercial establishments?
A: No, this heater is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
PARTS AND COMPONENTS
- Power regulator
- Light indicator
- Temperature knob
- Handle
NOTE:
The graphics in this manual are schematic representations and may not exactly
match the device.
BEFORE USE
- This device is packaged in a way as to protects it during transport. Take the device out of its box and remove all packaging materials. You can keep the original box and other packaging elements in a safe place. This will help you prevent damage to the device when transporting it in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
- Make sure all parts and components are included and in good condition. If there is any piece missing or in bad condition, contact the official Cecotec Technical Support Service immediately.
OPERATION
Power regulator
- Switch off: position 0.
- Ventilation mode: select the first position.
- Heating at reduced power: turn the selector (right) to the second position.
- Full power heating: turn the selector (right) to the third position.
Temperature knob
Turn the temperature knob clockwise to increase temperature, and anticlockwise
to decrease it
CLEANING AND MAINTENANCE
- When your heater needs cleaning, wipe the outside surfaces of the heater with a damp cloth.
- Do not rinse it directly with water. Be sure to unplug the appliance before cleaning.
- To prolong the heater’s lifespan, do not dismantle the heater yourself in the event of a fault.
- Send your heater to a relative ID after-sales service centre or supplier for inspection of suitability.
TECHNICAL SPECIFICATIONS
- Product reference: 08252/08259
- Product: ReadyWarm 2000 Max Force Black/White
- Power: 1800 W – 2000 W
- Voltage: 220-240 V~
- Frequency: 50/60 Hz
08252/08259 ReadyWarm 2000 Max Force Black/White
Item| Symbol| Value| Unit| Item| Unit
Heating power| Type of heat input, for electric storage local space heaters
only (single select)
Nominal
heat output
| Pnom| 1.8 –
2.0
| kW| Manual heat charge control
with integrated thermostat
| [no]
Minimum heat output (indicative)| Pmin| 1.0| kW| Manual heat charge control
with room and/or outdoor temperature feedback| [no]
Maximum
continuous heat output
| Pmax| 2.0| kW| Electronic heat charge control
with room and/or outdoor temperature feedback
| [no]
Auxiliary electricity consumption| | Fan assisted heat output| | [no]
At nominal heat output| elmax|
0,000
| kW| Type of heat output/room temperature control (single select)
At minimum
heat output
| elmin|
0,000
| kW| Single stage heat output and no room temperature control| [no]
In standby
mode
| elSB|
0,000
| kW| Two or more manual stages,
no room temperature control
| [no]
| With mechanic thermostat room temperature control| [yes]
---|---|---
| | | | With electronic room temperature control| [no]
| | | | Electronic room temperature control plus day timer| [no]
| | | | Electronic room temperature control plus week timer| [no]
| Other control options (multiple selections possible)
| | | | Room temperature control, with presence detection| [no]
| | | | Room temperature control, with open window detection| [no]
| | | | With distance control option| [no]
| | | | With adaptive start control| [no]
| | | | With working time limitation| [no]
| | | | With black bulb sensor| [no]
Contact details:| Cecotec Innovaciones S.L
Av. Reyes Católicos nº60 – 46910, Alfafar (Valencia, Spain)
Technical specifications may change without prior notification to improve product quality. Made in China | Designed in Spain
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES
- This symbol indicates that, according to the applicable regulations, the product and/or batteries must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/ batteries/accumulators and take them to a collection point designated by the local authorities.
- Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries.
- Compliance with the above guidelines will help protecting the environment.
TECHNICAL SUPPORT AND WARRANTY
Cecotec shall be liable to the end user or consumer for any lack of conformity
that exists at the time of delivery of the product under the terms,
conditions, and deadlines established by the applicable regulations.
It is recommended that repairs be carried out by qualified personnel.
If at any moment you detect any problem with your product or have any doubt,
do not hesitate to contact the official Cecotec Technical Support Service at
+34 963 210 728.
COPYRIGHT
The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.