Invicta LiFePO4 Hybrid Starter Instruction Manual

Invicta LiFePO4 Hybrid Starter

Product Information

Specifications

• Battery Type: Invicta Hybrid Starter LiFePO4 Battery
• Bluetooth Connectivity: Yes
• Operating Temperature Range: Please refer to the specification sheet for recommended operating temperatures

Warnings

• Please read the instructions and warnings carefully before using the battery
• If there are any signs of damage or malfunction, discontinue use

Tips
For best results, please follow the installation and usage instructions provided

Product Usage Instruction

Installation
Please refer to the Invicta Hybrid fitment guide for installation instructions.

Charging
Ensure the battery is fully charged before use. Use a compatible charger and follow the charger’s instructions for proper charging.

Using the Jump Start Feature
Before activating the Jump Start feature, isolate any external loads such as fridge, inverter, or lights to assist the starting capabilities. The Jump Start feature is designed for convenience and should not be relied upon as the only and last resort for starting your vehicle. It should only be used occasionally to avoid excessive wear and tear on the battery.

Under-bonnet and High-Heat Applications
The Invicta Hybrid Battery is rated to be installed in high-heat applications. However, it is recommended to ensure there is airflow around the battery to reduce the occurrence of BMS over-temp disconnect. The over-temp disconnect will activate once the internal temperature of the battery reaches 80°C and reconnects at 60°C.

Parallel Configuration

1. Ensure all batteries to be in the parallel configuration have been fully charged individually and are all the same model.
2. Ensure the voltage difference between each battery is no more than 0.2V.
3. After charging, set aside and allow to rest for 8 hours.
4. Cable sizing should be suitable for the load requirement. Ensure all connecting cables lengths are of the same length.
5. Be careful not to reverse the polarity of the poles or short circuits while connecting the cables.
6. It is prohibited to series a paralleled configuration.
7. Once in Parallel configuration, ensure a full charge is completed at least every 3 months.
8. A parallel configuration must be a true parallel connection as shown in the manual, any other parallel configuration may result in unexpected issues and void the warranty.
9. Once in Parallel configuration, the system must be charged and discharged as a system.

Accessories/Ignition
Refer to the manual for specific instructions on connecting accessories and ignition systems based on different configurations.

Bluetooth Feature
All Invicta Hybrid Starter batteries come with Bluetooth connectivity. To use the Bluetooth feature:

1. Download the Invicta Hybrid App from the Apple Store or Google Play. Do not download the Invicta Lithium app as it is not compatible with Invicta Hybrid batteries.
2. Open the Invicta Hybrid app on your phone.
3. Find and connect to the battery using the Bluetooth battery ID you recorded.
4. Screen 1 will display the battery capacity as a percentage, its status, and cycles.
5. Screen 2 will display the voltage of the battery, current in/out, and temperature.

FAQ

• Q: Can I use the Jump Start feature frequently?
  A: The Jump Start feature should only be used occasionally to avoid excessive wear and tear on the battery.

• Q: Can I install the Invicta Hybrid Battery in high-heat applications?
  A: Yes, the Invicta Hybrid Battery is rated to be installed in high-heat applications. However, it is recommended to ensure there is airflow around the battery to reduce the occurrence of BMS over-temp disconnect.

• Q: Can I connect multiple batteries in a parallel configuration?
  A: Yes, you can connect multiple batteries in a parallel configuration. Please follow the instructions provided in the manual for proper parallel configuration.

• Q: How often should I charge the parallel configuration system?
  A: It is recommended to perform a full charge on the parallel configuration system at least every 3 months.

• Q: Is the Invicta Hybrid Battery compatible with the Invicta Lithium app?
  A: No, the Invicta Hybrid Battery is not compatible with the Invicta Lithium app. Please make sure to download the Invicta Hybrid App for proper functionality.

Welcome to your new
Invicta Hybrid Starter LiFePO4 Battery. Please read the instructions and warnings on this card carefully to ensure you get the most out of your battery.

Safety Instructions

Warnings

• Keep away from direct heat, high voltage and direct sunlight.
• Never short-circuit the positive and negative terminals.
• Never ship or store batteries along with metal.
• Never disassemble, alter or drill the battery.
• Avoid direct impact on the battery.
• Never throw battery
• Never submerge the battery in water.
• Never place the battery in the fire
• Ensure the charge rate is within the parameters of the battery
• Do not exceed the discharge parameters of the battery
• Do not reverse the polarity of the battery

Tips

• The Invicta Hybrid Starter battery is primarily a starting/cranking battery that has deep-cycle capabilities.
• If the battery goes below the over-discharge protection voltage or the over-discharge protection is activated, charge the battery within 15 days.
• The battery must be charged within 6 months of receipt
• Battery should be maintenance charged every 3 months to extend life
• Ideal storage temperature 20oC – 35oC
• Do not leave the battery in a low state of charge for long periods.
• Isolate battery from system if not in use for more than 7 days
• Keep the battery away from high temperatures of 800C or more
• The Jump Start feature can reserve starting capacity for up to 48 hours. After 48 hours an external jump start/charge may be required.
• If the battery shows signs of deformation, heat or smell, immediately discontinue use.

Installation

• Inspect the battery for any damage and record your Bluetooth battery ID and serial number
• Connect to the battery Bluetooth using the Invicta Hybrid app
• Check you have the right battery for your vehicle
• Check the place of installation, ensuring it is clean and ready
• Ensure you have the right tools, equipment and PPE
• Ensure the application and any accessories are off
• Carefully lift and lower the battery using the handles supplied
• Do not over-tighten any brackets, nuts, bolts or terminals.
• Hand tighten plus half turn is sufficient
• Connect negative cables to the negative terminal and positive cables to the positive terminal. Be careful not to short-circuit the battery.
• If paralleling the battery please follow the instructions in this manual
• If adding a deep-cycle battery, follow the instructions in the paralleling section
• Newer vehicles may require a flash tune and the smart alternator turned off -please refer to the Invicta Hybrid fitment guide for this.

Charging

• The Invicta Hybrid Starter can be charged from most car alternators.
• When using an AC-DC or DC-DC charger, a lithium setting is recommended.
• If the battery is in sleep mode, you may need to wake the battery up using the Jump Start feature to enable the charge
• Please ensure your charger is matched to the current rating of your battery.
• Specifications for your battery can be found at invictalithium.com.au
• To fully charge a lithium battery to 100% you will need to bulk charge the battery between 14.4V and 14.6V
• We recommend a top-up charge using a lithium-specific charger every 3 months.

Using the Jump Start feature

• The BMS in the Invicta Hybrid Starter will automatically reserve a small amount of capacity for the Jump Start feature. When the main capacity is fully discharged the BMS will reserve the ‘Jump Start’ capacity for up to 48hrs. To activate the Jump Start feature and use the reserve capacity simply use the mobile app or press the button on top of the battery until the light flashes red one time. This will release the reserve capacity for approx. 30 seconds and allow you to start your engine. Once the application is started allow the battery to charge for at least 15min before turning the engine off again.
• Before activating the Jump Start feature we recommend isolating any external loads (i.e. fridge, inverter, lights) to assist the starting capabilities.
• The Jump Start feature is designed for convenience and not to be relied upon as your only last resort for starting your vehicle. It should only be used occasionally to avoid excessive wear and tear on the battery.

Under-bonnet and high-heat applications

• The Invicta Hybrid Battery is rated to be installed in high-heat applications. Although the battery can withstand high heat, every effort should be made to ensure there is airflow around the battery to reduce the occurrence of BMS over-temp disconnect.
• The over-temp disconnect will activate once the internal temperature of the battery reaches 80oC and reconnects at 60oC. Please see the specification sheet for recommended operating temperatures.

Parallel Configuration

There are strict conditions under which the Invicta Hybrid Starter range can be configured in Parallel systems. Please note these conditions below.

• Invicta Hybrid Starter batteries can only be paralleled in systems up to 6. They cannot be placed in a series configuration.
• All negative connections from accessories and ignition should go to battery one.
• All positive connections from accessories and ignition should go to battery two.
• If adding a deep-cycle battery to the system, this must be separated from the hybrid via a DC-DC charger (fuse-relay is required if DC-DC doesn’t have an inbuilt fuse-relay)

1. Ensure all batteries in the parallel configuration have been fully charged individually and are all the same model.
2. Ensure the voltage difference between each battery is no more than 0.2V
3. After charging, set aside and allow to rest for 8 hours.
4. Cable sizing should be suitable for the load requirement. Ensure all connecting cables lengths are of the same length.
5. Be careful not to reverse the polarity of the poles or short circuits while connecting the cables.
6. It is prohibited to series a paralleled configuration.
7. Once in Parallel configuration ensure a full charge is completed a minimum of every 3 months
8. A parallel configuration must be a true parallel connection as shown below, any other parallel configuration may result in unexpected issues and void the warranty.
9. Once in Parallel configuration, the system must be charged and discharged as a system.

Bluetooth Feature

• All Invicta Hybrid Starter batteries come with Bluetooth connectivity. The app is available to download on the Apple Store and Google Play and is compatible with most smartphones.
• To download the app you can scan the QR code. Ensure that you download the Invicta Hybrid App and NOT the Invicta Lithium app. The Invicta Lithium app will not work on Invicta Hybrid batteries due to the different features of each.

How To Use The Bluetooth Feature

1. Open the Invicta Hybrid app on your phone
2. Find and connect to the battery (if using multiple batteries refer to the Bluetooth battery ID you recorded)
3. Screen 1 – Capacity as a percentage, its status, and cycles. There are four status options (Standby/Discharge/Charge/Protection)
4. Screen 2 – Voltage of battery, Current In/Out (+/-), Temperature (Orange internal temperature), Capacity is shown as Ah.
5. Screen 3 – Contact Details and general information
6. Jump Start Feature – Only available once the battery has used its main capacity. The reserve must be activated within 48 hours of being available

If you cannot connect to the battery Bluetooth, please check the following

• You have downloaded the correct app
• No one else is connected to the app
• Your Bluetooth is on and you have allowed location services

Warranty

• Invicta Hybrid Starter batteries have a 3-year full replacement warranty, If you would like to register your battery you can do this via the Invicta Lithium website www.invictalithium.com.au/warranty-registration/. A copy of the warranty statement can be found at www.invictalithium.com.au.
• If you’re unsure if your battery will be covered under warranty in its current application or if you are having issues with your Invicta battery, please contact the team at SPB on 1300 001 772 or info@spb.net.au.
• To claim a warranty please return the product to your retailer or contact SPB and ensure you have your proof of purchase and serial number. Do not send the product without a Return Authority.

Contact Details and Information

• A range of resources can be found at invictalithium.com.au. This includes specifications, product registration and our warranty statement. If you require further assistance with your Invicta battery, please contact the team at Sealed Performance Batteries (SPB) at 1300 001 772 or info@spb.net.au.
• Invicta is a brand of SPB, a company that has over 25 years of experience in energy storage and is located in Brisbane, Sydney and Melbourne. For more information on SPB please visit spb.net.au.

References

• Invicta Lithium Batteries | LiFePO4 Lithium Batteries
• Invicta Lithium Batteries | Product Warranty Registration
• Invicta Lithium Batteries | LiFePO4 Lithium Batteries

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>