AEROMOTIVE 18673 Camaro Stealth Kits Instruction Manual

: June 17, 2024
: AEROMOTIVE

Table of Contents

AEROMOTIVE 18673 Camaro Stealth Kits
Product Information
Product Usage Instructions
INSTALLATION INSTRUCTIONS
Aeromotive-Related LS Components
AEROMOTIVE, INC. LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AEROMOTIVE 18673 Camaro Stealth Kits

Product Information

Specifications

Product Model: 18673, 19874
Fuel system pressure: Under pressure
Recommended fuel line: Teflon braided line with machine-crimped hose ends
Recommended additional product: 16306-speed pump controller
Installation expertise required: Detailed knowledge of automotive systems and repair procedures
Fuel handling precautions: Work in a well-ventilated area with an approved fire extinguisher nearby, extinguish all open flames, prohibit smoking, and eliminate all sources of ignition in the area of the vehicle
Fuel pump outlet port: AN-08 ORB (O-ring Boss Ports)
Fuel pump return port: AN-08
Fuel compatibility: Pump Gas, Race Gas, E85 Alcohol/Ethanol
Aeromotive Related LS Components:
- Fuel Filters: 12301 (pump/race gas), 12335 (race gas/E85), 12305 (filter bracket)
- Fuel Pressure Regulators: 13101 (10AN ports), 13109 (6AN ports)
- Electrical Components: 16301 (pump wiring kit), 16306 (pump speed controller)
- Check Valves: 15106 (6AN), 15107 (10AN)
- Fuel Pressure Gauge: 15633 (dry 0-100psi)
- Fuel Rails: 14106 (LS1/LS6), 14114 (LS2), 14115 (LS3/L76), 14142 (LS7), 14147 (LS1, Edelbrock 29085), 14156 (Platinum LS1/LS6)

Product Usage Instructions

Installation Precautions

Before starting the installation process, please ensure that you have the following:

Detailed knowledge of automotive systems and repair procedures
A well-ventilated work area
An approved fire extinguisher nearby
All open flames extinguished
No smoking in the area
All sources of ignition eliminated

Fuel System Pressure Relief

Before opening the fuel system, it is important to relieve the pressure.
Follow the procedure and precautions outlined in the appropriate vehicle service manual.

Fuel Line Recommendation

We recommend using a Teflon braided line with machine-crimped hose ends.
This eliminates the possibility of fuel vapors permeating through the fuel line.

Additional Product Recommendation

We highly recommend using the 16306-speed pump controller.
This will keep the fuel cool and reduce noise inside the passenger compartment.

Installation Expertise Requirement

Installation of this product requires detailed knowledge of automotive systems and repair procedures.
We recommend that this installation be carried out by a qualified automotive technician.

Fuel Handling Precautions

Installation of this product requires the handling of gasoline.
Ensure you are working in a well-ventilated area with an approved fire extinguisher nearby.
Extinguish all open flames, prohibit smoking, and eliminate all sources of ignition in the area of the vehicle before proceeding with the installation.

Fuel Pump Installation

Support the rear end (complete IRS subframe) with a suitable jack. A transmission jack works best for this purpose. Remove the four…
Carefully remove the fuel pump assembly so as not to bend the float arm. There will also be a fuel transfer tube located on the bottom side of the assembly.
- Release this connection and let it fall back into the tank. Refer to FIGURE 1-3 for a visual representation of the internal workings of your fuel tank.
With the fuel pump assembly removed from the tank, remove the fuel level sensor. Refer to FIGURE 1-4 for guidance.
Take the Aeromotive fuel pump assembly and slide the leveling unit into it as illustrated in FIGURE 1-5.
- Note that when twisting the bottom tabs inward, be sure not to twist them into the wires on the bottom of the leveling unit.
- Move the leveling arm through its full range of motion to ensure it clears the bracket tabs.

FAQ

Q: What fuels are compatible with this product?

A: This product is compatible with Pump Gas, Race Gas, and E85 Alcohol/Ethanol.

Q: Do I need any additional Aeromotive components for my LS engine?

A: Yes, you may require additional Aeromotive components such as fuel filters, fuel pressure regulators, electrical components, check valves, fuel pressure gauges, and fuel rails. Refer to the specifications section for more details.

INSTALLATION INSTRUCTIONS

WARNING!

The fuel system is under pressure. Do not open the fuel system until the pressure has been relieved.
Refer to the appropriate vehicle service manual for the procedure and precautions for relieving the fuel system pressure.
This pump assembly is a high-performance factory replacement unit.

Key features:

Drops directly into the factory fuel tank (NO CUTTING REQUIRED).
Utilizes the factory jet siphon system so it operates just like GM intended.
High flow pre-filter built into an inlet of the pump.
Includes fuel level mounting bracket for factory leveling unit.
NOTE: The use of a Teflon braided line with machine-crimped hose ends is recommended.
This eliminates the possibility of fuel vapors permeating through the fuel line.
The use of a 16306-speed pump controller is also highly recommended, this will keep the fuel cool and reduce noise inside the passenger compartment.

CAUTION:

Installation of this product requires detailed knowledge of automotive systems and repair procedures.
We recommend that this installation be carried out by a qualified automotive technician.
Installation of this product requires the handling of gasoline.
Ensure you are working in a well-ventilated area with an approved fire extinguisher nearby.
Extinguish all open flames, prohibit smoking, and eliminate all sources of ignition in the area of the vehicle before proceeding with the installation.
The enclosed Aeromotive fuel pump utilizes an AN-08 ORB (O-ring Boss Ports) style outlet port and AN-08 return port; these ports are NOT PIPE THREAD and utilize NO THREAD SEALANT.

NOTICE TO INSTALLER:

Installation of this fuel pump requires fuel system conversion to a return-style fuel system (use of a bypass-style regulator).
Also, note that a check engine light may be present after installation due to the factory returnless system being modified. This can be turned off with tuning software.
NOTE: Due to tight clearance between the top of the fuel tank and the body, Aeromotive includes fuel tank strap spacers and high-density foam to space the tank down.

Compatible Fuels:

Pump Gas Race Gas E85 Alcohol/Ethanol

Fuel Filters:

12301 (pump/race gas) 10 micron
- 12335 (race gas/E85) 40 micron
12305 (filter bracket)

Fuel Pressure Regulators:

13101 (10AN ports)
- 13109 (6AN ports)

Electrical Components

16301 (pump wiring kit)
- 16306 (pump speed controller)

Check Valves:

15106 (6AN)
- 15107 (10AN)
Fuel Pressure Gauge:
- 15633 (dry 0-100psi)
Fuel Rails:
- 14106 (LS1/LS6)
- 14114 (LS2)
- 14115 (LS3/L76)
- 14142 (LS7)
- 14147 (LS1, Edelbrock 29085)
- 14156 (Platinum LS1/LS6)

TOP PLATE LAYOUT

The following steps are typical of most installations:

Disconnect the negative battery cable and drain the fuel tank.
Raise and support the vehicle.
Remove the exhaust and rear wheels from the vehicle.
Remove the driveshaft heat shield, drive shaft, and fuel tank heat shield.
Remove the emergency brake cables from the three-way tee and swing them towards the rear of the vehicle.
Remove the lower shock bolts.
Disconnect the rear subframe wiring located on the passenger side frame rail.
Disconnect all the following connections in Figure 1-1.
Support the rear end (complete IRS subframe) with a suitable jack (transmission jack works best).
- Remove the four 24mm bolts that hold the subframe in.
- Carefully lower the rear end, paying close attention to the brake lines on each side of the frame.
- There is enough length on the brake lines to get the tank out without removing the calipers.
- Once lowered, support the complete IRS subframe with jack stands.
Remove the evaporator. This is done by unplugging all hoses and wires and removing the two 10mm bolts.
Unplug and remove the wiring harness connection at the tank on the passenger side.
Remove the fuel tank strap mounting bolts (15mm), and tank straps and drop the tank out of the car.
- NOTE: It’s recommended to do this with two people.
Now remove the pressure feed line and pressure sensor.
- Also, remove the lock ring holding the fuel pump module in place.
- NOTE: The fuel pump module is spring-loaded and will pop up. FIGURE 1-2
Carefully remove the fuel pump assembly so as not to bend the float arm.
- There will also be a fuel transfer tube located on the bottom side of the assembly.
- Release this connection and let it fall back into the tank.
- The figure below gives you a visual of the internal workings of your fuel tank. FIGURE 1-3
With the fuel pump assembly removed from the tank, remove the fuel level sensor. FIGURE 1-4
Now take the Aeromotive fuel pump assembly and slide the leveling unit into it as illustrated in FIGURE 1-5.
- NOTE: When twisting the bottom tabs inward, be sure not to twist them into the wires on the bottom of the leveling unit.
- Move the leveling arm through its full range of motion to ensure it clears the bracket tabs.
Cut the two wire connectors off of the fuel level sensor and crimp them onto the two wires provide on the pump.
- NOTE: The sensor is a resistance output only, wiring polarity is bi-directional.
Make sure to place the factory o-ring in the receiver groove on the tank Figure 1-6.
- Failure to do so will result in fuel leakage and require the removal of the tank again.
Now the fuel pump is ready to install in the tank. The siphon connection has to be made as the fuel pump is being lowered into the fuel tank. FIGURE 1-7.
- NOTE: Bend the flex hose with the orange check valve on the Aeromotive pump assembly, so it points toward the float level.
Use the positioning marks on the pump to align the unit. FIGURE 1-8.
- Replace the lock ring on the top of the fuel pump assembly and rotate it to the “locked” position.
- If re-using the factory feed line, attach it to the Aeromotive pump at this time.
- NOTE: You must install a by-pass style regulator with a return line for the fuel pump to function correctly.
- Failure to do so will result in poor performance and fuel pump/system failure.
Affix the supplied foam strip to the top of the tank as shown in FIGURE 1-9.
Cut or splice the factory fuel level wires and attach them to the fuel level studs. Make sure you use stranded, insulated copper wire, with matching crimp-type connectors for all connections.
- Use the supplied rubber terminal boots to protect the terminals from the elements.
- NOTE: Position the fuel tank under the vehicle and allow yourself enough room to make the wire connections.
Since the factory GM fuel pump is pulse-modulated you can not use the factory fuel pump wires to trigger the relay.
- Find a suitable 12V key on the ignition source for the #85 connection on the relay.
- Hooking the factory wiring directly up the Aeromotive unit could result in wiring damage or pump failure
Now the fuel tank is ready to be installed in the vehicle. Attach the return line to the Aeromotive top plate before installing the tank (15605 for the 18673 and 15607 for the 18674). Coil the return lineup to keep it out of your way.
- Take the supplied fuel tank spacers and place them between the tank straps and body. See FIGURE 1-13.
Now reverse steps 12-1 to finish up the tank installation.
Route the return line under the vehicle noting to keep it away from heat and moving suspension components.
Find a suitable place in the engine bay to mount a return-style regulator. Plumb the regulator per the manufacturer’s installation instructions.
Key on to check for leaks and to set fuel pressure. If any leaks are found, immediately discontinue the use of the vehicle and repair the leak(s)! This finishes up the installation of your new Aeromotive Stealth fuel pump.

AEROMOTIVE, INC. LIMITED WARRANTY

This Aeromotive Product, with proof of purchase dated on or after January 1, 2003, is warranted to be free from defects in materials and workmanship for one year from the original date of purchase.
No warranty claim will be valid without authentic, dated proof of purchase.
This warranty is to the original retail purchaser and none other and is available directly from Aeromotive and not through any point of distribution or purchase.
If a defect is suspected, the retail purchaser must contact Aeromotive directly to discuss the problem, and possible solutions and obtain a Return Goods Authorization (RGA), if deemed necessary by the company.
Please call 913-647-7300 and dial option 3 for the technical service dept. All returns must be shipped freight pre-paid to the company and with a valid RGA before they will be processed.
Aeromotive will examine any product returned with the proper authorization to determine if the failure resulted from a defect or from abuse, improper installation, misapplication, or alteration.
Aeromotive will then, at its sole discretion, return, repair, or replace the product.
If any Aeromotive product is determined defective, the buyer’s exclusive remedy is limited in value to the sale price of the good.
In no event shall Aeromotive be liable for incidental or consequential damages.
Aeromotive expressly retains the right to make changes and improvements in any product it manufactures and sells at any time.
These changes and improvements may be made without notice at any time and without any obligation to change the catalogs or printed materials.
Aeromotive expressly retains the right to discontinue at any time and without notice any Aeromotive product that it manufactures or sells.
This warranty is limited and expressly limits any implied warranty to one year from the date of the original retail purchase on all Aeromotive products.
No person, party, or corporate entity other than Aeromotive shall have the right to: determine whether or not this Limited Warranty applies to any Aeromotive product, authorize any action whatsoever under the terms and conditions of this Limited
Warranty assumes any obligation or liability of any nature whatsoever on behalf of Aeromotive under the terms and conditions of this Limited Warranty.
This Limited Warranty covers only the product itself and not the cost of installation or removal.
This Limited Warranty is in lieu of and expressly excludes any and all other warranties, expressed or implied.
This Limited Warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
Aeromotive, Inc. 7805 Barton Street, Lenexa, KS 66214 Phone:913-647-7300 Fax: 913-647-7207