GLOMEX WeBBoat 4G Lite EVO High Speed Antenna User Guide

June 9, 2024
GLOMEX

GLOMEX WeBBoat 4G Lite EVO High Speed Antenna logo

GLOMEX WeBBoat 4G Lite EVO High Speed Antenna

GLOMEX WeBBoat 4G Lite EVO High Speed Antenna product

Assembly steps

STEP 1 Open the weBBoat 4G Lite EVO upper radome using a screwdriver (not supplied).
STEP 2 Pull out the SiM card tray by pushing the button with a SIM card needle (not supplied) or a pen tip. Place the SIM card into the SIM card tray and slide the SIM card tray back into the slot.
IMPORTANT: Insert the SIM card when weBBoat 4G Lite EVO is off. We recommend to remove the SIM PIN code before inserting the SIM card into the weBBoate SIM slot. Also, the SIM PIN code can be inserted from the App (STEP 8).
NOTE: Please note that US carriers do not use PIN codes.
STEP 3 Connect the weBBoat 4G Lite EVo to a 12 or 24 Vdc source
IMPORTANT: This unit is not protected against excessive current or short circuit. It is recommended to use a 1 amp fuse for protection. purposes during installation.
STEP 4 Download and install the weBBoat APP on your device from the APP store (for iOs devices) or from Goggle Play (for Android devices) Scan the QR code below NOTE: This Quick Reference Guide refers to the iOS version. The screens for the Android will differ slightly.
STEP 5 Connect your mobile device (e.g. smartphone) to the weBBoat 4G Lite EvO WiFi network . GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
03The default wiFi network name (SSID) is weBBoat XXXX (where XXXX is a unique string for each weBBoat” 4G Lite EVO) and it’s not password protected.
NOTE: It is advised after initial setup to create a password (minimum 8 characters) to secure the weBBoat 4G Lite EVO network. (see STEP 12).
STEP 6 Open the weBBoat App. Tap the “+” button in the top right corner .GLOMEX WeBBoat 4G Lite EVO High Speed Antenna 04 Tap the QR Code button. Scan the QR Code on the router and press “Save . GLOMEX WeBBoat 4G Lite EVO High Speed Antenna 05After scanning the QR code, you can rename the device if desired. Alternatively, you can connect the we BBoat 4G Lite EVO by tapping the “+ button on the top (Fig. 4) and insert manually the Serial Number located below the QR Code on the label (Fig. 5).
NOTE: The QR code and the Serial Number can be found on the bottom-right of page 2 of this quick reference guide.
STEP 7 Select the weBBoat 4G Lite EVO from the list .GLOMEX WeBBoat 4G
Lite EVO High Speed Antenna 06 Type the administrator password: admin . GLOMEX WeBBoat 4G Lite EVO High
Speed Antenna 07Then, tap Login button. NOTE FOR IOS
USERS: for quick access, tap the star icon to select weBBoat device in the list.
STEP 8 In the “Setup Wizard”, select the language (English, Italian, French, Spanish and German). English is the default setting . GLOMEX WeBBoat
4G Lite EVO High Speed Antenna 08To unblock the SIM card, enter the PIN code (if necessary). By default, the “Auto APN” option, which allows automatic connection, is selected (Fig. 8). To enter an APN manually, deselect the “Auto APN” option and a drop- down menu will be shown with a list of possible APNS. By selecting the value “none” from this list, it will be possible to manually enter a custom APN. GLOMEX WeBBoat 4G Lite EVO High Speed Antenna 09 NOTE: Check the correct APN with the Internet Service Provider (SP) of the SIM card. If the APN you need is not included in the default list, please contact us at
webboat@glomex.it.
STEP 9 In “Setup Wizard”, the Auto switch option is disabled by default. Enable “Auto switch” function to switch automatically from WiFi to 4G/3G if the external WiFi Hotspot signal (i.e. marina WiFi) is lost. While using the 4G/3G connection, if the same external WiFi Hotspot (i.e. marina WiFi) is detected again, weBBoat 4G Lite EVO will switch the connection back from 4G/3G to WiFi automatically. To enable this option, tap “Enable” button (Fig. 8). Tap WiFi Scan button, GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
10select one of the available external WiFi networks. Tap OK button to join the network and then enter the password (if required). Tap “Save button to proceed .GLOMEX WeBBoat 4G Lite EVO High
Speed Antenna 12 WARNING: During the Auto switch configuration, the connection between the mobile device and weBBoat 4G Lite EVO will be lost. Please check the connection between the devices and if needed reconnect before proceeding. To skip the Setup Wizard, tap “Skip” button (not recommended).
MPORTANT: Tap “Save” button in “Setup Wizard” to save all configuration settings (Fig. 10). In the “Advanced Settings” section there is a “Auto switch Configuration” section GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
11 in which it is possible to customize the operation of the “Auto switch mode by redefining the priority of the various internet sources: WiFi (Default Priority 1), Mobile ( Default Priority 2) and SAT (Default Priority 3).
STEP 10 After tapping “Save” button, the Control Panel will be shown automatically. This section includes all information related to the signal, the SIM card and the APN in use (Fig. 13). If the Auto switch function is not enabled, enable it by tapping “Auto switch” button .GLOMEX WeBBoat 4G Lite
EVO High Speed Antenna 13 STEP 11 In the “Control Panel”, choose one of the following Mobile modes (Fig. 13) Auto: weBBoat 4G Lite EVO is connected to the network that provides the best Internet connection 4G only: weBBoat 4G Lite EVO is connected to the 4G network only. 3G only: weBBoat 4G Lite EVO is connected to the 3G network only. Other ways of managing Mobile /WiFi operations from the Control Panel are: Auto switch: as described on step 9.
Mobile Only: the weBBoat is forced to work in Mobile regardless of other available Internet sources. WiFi Only: the weBBoat is forced to work in WiFi regardless of other available Internet sources. SAT Only: the weBBoat is forced to work using the SAT input regardless of other available Internet sources.
NOTE: Please note that other Wifi networks nearby could affect the speed performance of the weBBoat 4G Lite EVO.
STEP 12 To customize the name of the Wi-Fi network generated by weBBoat 4G Lite EVO (SSID) and its password, tap the Menu button (Fig. 14) and select “Advanced settings”. Go to “WiFi Configuration” section. Change the SSID in the related field and select the encryption type. Type the password and tap Save button.GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
15 Suggestion: Choose WPA2-PSK encryption for better security.
NOTE: Do not use spaces or special characters in the name of the Wi-Fi network (SSID) and password network (SSID) and the password, the weBBoat 4G Lite EVO will be rebooted automatically. Close the weBBoat App, reconnect your mobile device (e.g smartphone) to the new Wi-Fi network of the weBBoat 4G Lite and then reopen the App. After changing the name of the Wi-Fi
STEP 13 To change the Administrator password, tap the Menu buttonGLOMEX
WeBBoat 4G Lite EVO High Speed Antenna 14 and tap “Advanced settings”. In the “Administrator Password” section enter the new administrator password in both fields and tap Save button
IMPORTANT: Keep the new password in a safe place and do not forget it. if the administrator password is lost, you must restore the device to the default factory settings using the Reset button placed in the back of the router.GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
16 To restore the device, push and hold the Reset button for at least 5 seconds. The Reset button can be released when all 5 signal strength LEDS  GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
17are ON. When the weBBoat 4G Lite EVO reboots, it will reset all custom changes to factory defaults. Close the weBBoat App, reconnect your mobile device (e.g. smartphone) to the Wi-Fi network of the weBBoat 4G Lite EVO and then reopen the App.
STEP 14 When firmware and Auto APN database updates are available, they will appear as an Upgrade Button in the “System Updates” menu GLOMEX WeBBoat
4G Lite EVO High Speed Antenna 18 Tap “Upgrade” button to perform the upgrade and wait for a few minutes.
IMPORTANT: When the Firmware upgrade is completed, weBBoat 4G Lite EVO will reboot automatically. Close the weBBoat App, reconnect your mobile device (e.g. smartphone) to the Wi-Fi network of the weBBoat” 4G Lite EVO and then reopen the App. PLEASE DO NOT POWER OFF THE WEBBOAT 4G UTE EVO DURING THE INSTALLATION
STEP 15 SMS MANAGEMENT The SMS section on the menu (Fig. 14) shows a number that indicates the number of received and unread SMS on the SIM installed in the weBBoat”. By clicking on SMS you access the SMS section where you can read the SMS, monitor your credit and, if the SIM is enabled send messages .GLOMEX WeBBoat 4G Lite EVO High Speed Antenna
19www.glomex.it
info@glomex.it
www.glomex.uS-info@glomex.us

FCC ID: 2AET4RUT240A
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals