AEROMOTIVE 17310 Fuel System Kit Instruction Manual

June 17, 2024
AEROMOTIVE

AEROMOTIVE 17310 Fuel System Kit

AEROMOTIVE-17310-Fuel-System-Kit-PRODUCT

Installation Instructions

17310 Installation Instructions

CAUTION:

  • Installation of this product requires detailed knowledge of automotive systems and repair procedures.
  • We recommend that this installation be carried out by a qualified automotive technician.
  • Installation of this product requires the handling of gasoline.
  • Ensure you are working in a well-ventilated area with an approved fire extinguisher nearby.
  • Extinguish all open flames, prohibit smoking, and eliminate all sources of ignition in the area of the vehicle before proceeding with the installation.
  • When installing this product, wear eye goggles and other safety apparel as needed to protect yourself from debris and sprayed gasoline.

WARNING!

  • The fuel system is under pressure.
  • Do not open the fuel system until the pressure has been relieved.
  • Refer to the appropriate vehicle service manual for the procedure and precautions for relieving the fuel system pressure.
  • Aeromotive system components are not legal for sale or use on emission-controlled motor vehicles.
  • Fuel Systems are designed for use with gasoline-based fuels only, up to 15% ethanol mix maximum with proper filter.

Kit Parts

This kit contains the following parts:

  • 1ea p/n 14116 Fuel Rails
  • 1ea p/n 13101 Fuel Pressure Regulator
  • 1ea p/n 18682 Fuel Pump Assembly
  • 1ea p/n 16307 Fuel Pump Wiring Kit
  • 1ea p/n 12305 Filter Bracket
  • 1ea p/n 12335 Filter Assembly, 40-micron
  • 1ea p/n 15107 One-Way Check Valve
  • 6ea p/n 15607 ORB-08 to AN-08 Fittings
  • 4ea p/n 15610 ORB-10 to AN-08 Fittings
  • 1ea p/n 15649 ORB-06 to AN-08 Fitting
  • 1ea p/n 15674 Y-Block, AN-08
  • 1ea p/n OR002-2910 AN-10 O-Ring

The enclosed Aeromotive Fuel System Kit is designed to give the end user a basic EFI fuel system, excluding the AN fuel lines and hose ends. It is intended to support a return-style, dual-fuel rail V-8 EFI application. The kit includes an AN-08 Y-Block in order to support dual fuel rail engines, plumbed in parallel, for optimum fuel flow and pressure control. A return line of AN-08 or 1/2” minimum size must be installed from the regulator back to the tank, after which base fuel pressure will be adjustable in a range between 30-120 PSI. The included regulator also provides a 1:1 ratio vacuum/boost reference, making the system suitable for all EFI engines, both Naturally Aspirated and Forced Induction. This installation instruction provides a diagram that outlines the overall layout of the fuel system intended with the enclosed components. The system diagram illustrates the components used, their locations relative to each other, and about fuel flow, including general fuel line routing and the AN fuel line sizes required. This is a system overview. Please refer to each component’s installation instructions for detailed installation help with that particular component. Please contact Aeromotive for any recommendations on fuel line or additional fitting requirements. Failure to follow the above recommendations may result in fuel leakage, bursting of the fuel lines, poor vehicle performance, and/or decreased fuel pump life! Improper installation will void all warranties for this product!

Aeromotive Commonly Used Hose-Ends:

  • 15650 – AN-06 Straight Hose End
  • 15651 – AN-06 45-Deg. Hose End
  • 15652 – AN-06 90-Deg. Hose End
  • 15653 – AN-08 Straight Hose End
  • 15654 – AN-08 45-Deg. Hose End
  • 15655 – AN-08 90-Deg. Hose End
  • 15663 – AN-08 180-Deg. Hose End

Aeromotive Commonly Used SS Braided Fuel Line;

  • 15701 – AN-06 4′ Length
  • 15702 – AN-06 8′ Length
  • 15703 – AN-06 12′ Length
  • 15704 – AN-08 4′ Length
  • 15705 – AN-08 8′ Length
  • 15706 – AN-08 12′ Length
  • 15711 – AN-08 16′ Length

Aeromotive Replacement Element Part Numbers;

  • 12601 – 10-M Fabric Element (For all ORB-10 Filters)
  • 12635 – 40-M SS Element (For all ORB-10 Filters)
  • 12001 – Filter O-Ring, 10-Pack (For all ORB-10 Filters)

General Guidelines

General Installation Cautions and Guidelines:

  • CAUTION: Ensure all components are mounted, and fuel lines are routed through the chassis per the diagram, and in a manner to clear any exhaust system components, especially exhaust headers, turbocharger down-pipes, mufflers, and tail-pipes, etc.
  • CAUTION: Ensure all components are mounted, and fuel lines are routed through the chassis per the diagram, and in a manner to safely clears any suspension components in the vehicle.
  • CAUTION: Ensure all components are mounted, and fuel lines are routed through the chassis per the diagram, and in a manner to safely clear any transmission, bell-housing, and or drive-line components.
  • CAUTION: Pressurize the fuel system and thoroughly check for fuel leaks, repairing any leaks found first, before cranking and/or starting the engine. Once the engine is running, again carefully check for fuel leaks, shutting down the vehicle immediately if necessary to perform any required repairs.
  • GUIDELINE: Mount the fuel pressure regulator in the engine bay, as close to the fuel rail/carb as possible.
  • GUIDELINE: Terminate the main, 10-gauge power for the included fuel pump wiring harness directly from the back of the alternator charging stud, or directly off the battery (+) post. Terminate the 10-gauge fuel pump ground wire to either end of the battery ground (-) cable, at the battery or chassis connection point.
  • GUIDELINE: Acquire and install quality AN-style hose and hose ends. Teflon or PTFE-based fuel line, though more costly, offers both long service life and resistance to permeation or vapor walk (where fuel vapors can “walk” through the line and contribute fuel smell to the area around where the car is stored).

Installation Outline:

Use the diagram below as an outline for the system installation. See individual installation instructions for specific recommendations.

AEROMOTIVE-17310-Fuel-System-Kit-FIG-1

LIMITED WARRANTY

AEROMOTIVE, INC. LIMITED WARRANTY

  • This Aeromotive Product, with proof of purchase dated on or after January 1, 2003, is warranted to be free from defects in materials and workmanship for one year from the original date of purchase. No warranty claim will be valid without authentic, dated proof of purchase.
  • This warranty is to the original retail purchaser and none other and is available directly from Aeromotive and not through any point of distribution or purchase.
  • If a defect is suspected, the retail purchaser must contact Aeromotive directly to discuss the problem, and possible solutions and obtain a Return Goods Authorization (RGA), if deemed necessary by the company. Please call 913-647-7300 and dial option 3 for the technical service dept. All returns must be shipped freight pre-paid to the company and with a valid RGA before they will be processed.
  • Aeromotive will examine any product returned with the proper authorization to determine if the failure resulted from a defect or from abuse, improper installation, misapplication, or alteration. Aeromotive will then, at its sole discretion, return, repair, or replace the product.
  • If any Aeromotive product is determined defective, the buyer’s exclusive remedy is limited in value to the sale price of the good. In no event shall Aeromotive be liable for incidental or consequential damages.
  • Aeromotive expressly retains the right to make changes and improvements in any product it manufactures and sells at any time. These changes and improvements may be made without notice at any time and without any obligation to change the catalogs or printed materials.
  • Aeromotive expressly retains the right to discontinue at any time and without notice any Aeromotive product that it manufactures or sells.
  • This warranty is limited and expressly limits any implied warranty to one year from the date of the original retail purchase on all Aeromotive products.
  • No person, party, or corporate entity other than Aeromotive shall have the right to: determine whether or not this Limited Warranty applies to any Aeromotive product, authorize any action whatsoever under the terms and conditions of this Limited Warranty, assume any obligation or liability of any nature whatsoever on behalf of Aeromotive under the terms and conditions of this Limited Warranty.
  • This Limited Warranty covers only the product itself and not the cost of installation or removal.
  • This Limited Warranty is in place of and expressly excludes any other warranties, expressed or implied. This Limited Warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

CONTACT

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals