SelectBlinds 1-2 Inch Single Cell Day Night Honeycomb Shades Owner’s Manual
- June 4, 2024
- SelectBlinds
Table of Contents
CordlessCellular
FabricShade
including Top-Down/Bottom-Up
& Day/Night Shades
owner’s handbook
1-2 Inch Single Cell Day Night Honeycomb Shades
INSTALLATION INSTRUCTIONS
Step 1. Check Package Contents
Missing part? Call 1-800-264-1190
The mounting hardware kit includes the following:
Part | Quantity |
---|---|
a. Mounting Brackets | 2 (for 18” to 36” wide shades) |
3 (for 361/8” to 48” wide shades)
4 (for 481/8” to 72” wide shades)
Shades ordered over 72” wide, will be (2) shades joined by a Connector Device.
The above bracket quantities apply for each shade.
b. 11/8” Screws| 2 per bracket
c. Hold Down Brackets| 2 per shaded
. 3/8” Screws| 2 per bracket (for hold downs)
e. Handle for Bottom Rail| 1
2 (for shades over 59” wide)
f. Handle for Middle Rail| 1 (for TDBU and Day/Night Shades)
2 (for shades over 59” wide)
g. Head Rail Connector| 1 for shades over 72” wide
[Note: one extra screw of each noted size is included for convenience]
Step 2. Tools Required
Screwdriver, tape measure, pencil, drill, drill bits, step ladder.
Note: use #6 plastic anchors for drywall or plaster mounting (not included).
Drill Bits: for screws, use a 3/32″ drill bit – for wall anchors, use a 1/4″
drill bit.
Step 3. Bracket Location and Installation
Your shade may be installed either inside the window frame or outside the
window frame.
A mounting bracket should be positioned about 1” to 6” from each end of the
headrail. For wider shades that require 3 or more brackets, these should be
spaced evenly between the two outermost brackets.
Always position the brackets such that there is no interference with the cords
and/or mechanisms inside the headrail. The procedure outlined below will
assure proper bracket placement.
Attaching the brackets:
The shape of head rails and mounting brackets varies by the style of shade.
For style ‘A’ [see illustrations below]: Lift the head rail into position such
that the inner front edge of the headrail slides into the slot at the front of
each bracket. Push the headrail upward until the flexible tab at the bottom of
each bracket snaps onto the back of the headrail. Check carefully to assure
that each bracket is properly secured.
For style ‘B’ [see illustration below]: Lift the Head Rail into position such
that the front edge of the bracket is under the inner front edge of the head
rail, and then push the head rail upwards until the flexible tab at the bottom
of each bracket snaps onto the back of the headrail. Check carefully to assure
that each bracket is properly secured.
For style ‘C’ [see illustration below]: To attach the brackets the locking arm should be facing out. Then position the bracket so that it engages the inner front and outer back of the head rail and then push the locking arm inward to lock it in place.
For Outside Mounting:
Clip the brackets onto the headrail as described above. Hold the shade level
at the height desired and center it over the window opening. Mark the exact
location of each bracket with a pencil. Remove the brackets from the head rail
and position the top of each bracket at the marked location and screw each
bracket into the wall or window molding using the 11/8” screws, pre-drill the
screw holes using a 3/32” drill bit.
For Inside Mounting:
Clip the brackets onto the headrail as described above. Hold the shade in
place and make a pencil mark at the rear of each bracket where it contacts the
inside of the window frame. Remove the brackets from the head rail and align
them with the marks. Attach each bracket using the 11/8” screws, and pre-drill
the screw holes using a 3/32” drill bit.
Step 4. Attach Handle(s)
Attach the Handle to the bottom rail as illustrated. The handle is designed to
minimize contact with the shade fabric. Always raise and lower the shade
SLOWLY(!) to assure that the pleated fabric stacks neatly.
Wider shades have (2) Handles – to precisely determine the correct position
for each handle, divide the total width of the shade by 4, and then attach one
handle that distance from each outside edge of the shade – always grasp both
handles when lifting and lowering the shade.
For TDBU and Day/Night cordless shades, attach the 2nd handle to the Middle
Rail as illustrated.
Step 5. How to Operate
IMPORTANT
Operating & Care Instructions for Cell Shades
READ CAREFULLY
- Make sure that the Handles have been attached to the rail(s) as described above (see Step 4)
- To maintain optimal performance of the springs that make your cordless shade function, lift and lower your shade through its full range of motion – all the way up and down – every day if possible.
- For shades with a single handle, which must be centered on the rail(s), lift or lower the shade slowly and evenly, keeping the rail(s) level, until the shade is positioned as desired.
- For wider shades with a double set of handles, grasp the handles using both hands and lift the shade slowly and evenly, being sure to keep the rail(s) level.
- If you have trouble lifting your cordless shade:
If the shade is left in one position for a long period of time, it might be necessary to lift and lower the shade several times to restore normal function.
If the shade has been fully raised for a long period of time, it might tend to spring back (rebound) slightly from the desired length position. This can also be remedied by lifting and lowering the shade several times.
Standard Shade
Always raise and lower the shade SLOWLY(!) to assure that the pleated fabric
stacks neatly. To lower the shade: grip the bottom rail handle and slowly pull
straight down. To raise the shade, grip the bottom rail handle and push it up
slowly.
Always keep the bottom rail level.
Top-Down Bottom-Up & Day/Night Cordless Shades
To raise and lower the shade from the bottom, follow the directions above. To
lower and raise the shade from the top: grip the middle rail handle and slowly
pull straight down/up.
Step 6. Installing Hold-Down Brackets
Hold-down brackets are provided for optional use. These brackets should be
used only if the shade is to be in a permanently lowered position. With the
shade fully lowered, make pencil marks at the outside ends of the bottom rail.
Brackets should be lined up to the pencil marks and screwed into place using
the 3/8” screws. Insert the pins protruding from the brackets into the holes
on both ends of the bottom rail (see illustration).
Step 7. 2-in-1 Connector for Wide Windows
Connect the Head Rails using the 2-in-1 Connector, as shown.
CLEANING
The vinyl head rail and bottom rail can be wiped clean with a damp sponge. To
clean the shade fabric, use a feather duster or vacuum lightly using the soft
brush attachment.
REPLACEMENT PARTS
In the event that replacement parts are ever needed, you may call:
1-800-264-1190
Please be sure to provide the following information, if possible:
- The complete model or catalog number of your product
- A description of the product
- A description of the part needed
LIMITED LIFETIME WARRANTY
The enclosed product is warranted to the original residential retail purchaser
as long as the product remains in the original window.
Covered:
Lifetime: Entire product against manufacturing defects (i.e. a flaw in the
product design, materials, or workmanship that causes the product to no longer
function)
5 years: All fabric
Not Covered:
Normal Wear and Tear
Any product that fails due to • abuse • exposure to salt air • improper
installation • accident • extraordinary use • improper operation • alterations
• improper cleaning • misapplication • damage from pests/ insects/pets •
improper handling • misuse Costs associated with • product removal •
transportation to and from the retailer • brand label removal • product re-
measure • incidental or consequential damages • product reinstallation •
shipping
In the event there are multiple blinds/shades in the same room, only the
defective blind/shade will be replaced.
To Report Shipping Damage: If damage occurred during shipping, call the
place of purchase and report within 7 calendar days, or else you may be denied
credit for your damaged product.
To Obtain Service: If you suspect this product has a manufacturing defect
in materials or workmanship: 1. Locate the sales receipt 2. Call place of
purchase. Any unauthorized returns will not be accepted.
Warranty Remedy: THIS SHALL BE YOUR SOLE REMEDY UNDER THIS LIMITED
WARRANTY.
If this product is found to have a manufacturing defect in materials or
workmanship, we will (at our discretion) do one of the following:
• repair the product • replace the product • refund the cost of the product
Colors vary from lot to lot and may not exactly match sample swatches or
previous purchases.
Discontinued items or color selections will be replaced with the closest
equivalent current product.
YOUR RIGHTS UNDER STATE LAW:
This lifetime limited warranty gives you specific legal rights, and you may
have other rights, which vary from state to state. Some states do not allow
limitations on how long a warranty lasts, so the above limitations may not
apply to you. No agent, representative, dealer, or unauthorized employee has
the authority to increase or alter the obligation of this warranty. This
lifetime limited warranty supersedes any previous versions.
WARNING
STRANGULATION HAZARD — Young children can be strangled by cords.
Immediately remove this product if a cord longer than 22 cm or a loop
exceeding 44 cm around becomes accessible.
Cordless
Cellular Fabric Shade Including
Top Down / Bottom-Up
& Day / Night Shades
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>