Hangzhou Meari 2AG7C-R833 IP Camera User Manual
- June 17, 2024
- Hangzhou Meari
Table of Contents
- Hangzhou Meari 2AG7C-R833 IP Camera
- Product Information
- Product Usage Instructions
- Information on Test Modes and Additional Testing Requirements
- Module User Manual
- Important Notice to OEM integrators
- End Product Labeling
- Manual Information to the End User
- FCC
- FCC Radiation Exposure Statement
- FAQ
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Hangzhou Meari 2AG7C-R833 IP Camera
Product Information
Specifications
-
Module Type: 802.11a/b/g/n WiFi & BLE 4.2 Module 1T1R
-
Integrated Chip: Single-chip 802.11a/b/g/n 1T1R WLAN and
Bluetooth Low Energy 4.2 combo chip -
Host Interface: USB 2.0
-
Dimensions: QFN40 5 x 5 mm
General
The module is a highly integrated single-chip WLAN and Bluetooth combo chip. It combines a WLAN MAC, a 1T1R capable WLAN baseband, BT Protocol Stack, BT Baseband, modem, and WLAN/BT RF in a single chip. It provides a complete solution for a high-performance integrated wireless LAN and Bluetooth controller.
Product Usage Instructions
Integration Instructions for Host Product Manufacturers
If the end product will involve multiple simultaneous transmitting conditions or different operational conditions for a stand-alone modular transmitter in a host, the host manufacturer must consult with the module manufacturer for the installation method in the end system.
RF Exposure Considerations
The device has been evaluated to meet general RF exposure requirements. When using the device in mobile exposure conditions, maintain a minimum distance of 20 centimeters between the radiator and your body.
Antennas
The radio transmitter with FCC ID: 2AG7C-R833 has been approved by the Federal Communications Commission to operate with the following antennas:
AntennaYJC-6N055-G09
-
Antenna Type: FPC antenna with IPEX connector
-
Gain (dBi): 3.82 (Max.) for 2.4G Band, 3.6 (Max.) for 5G
Band -
Frequency (MHz): 2400-2480, 5150-5250, 5250-5350, 5500-5700,
5745-5825
Antenna112010218
- Antenna Type: Omni antenna with IPEX connector
- Gain (dBi): 2.91 (Max.) for 2.4G Band, 3.81 (Max.) for 5G Band
- Frequency (MHz): 2400-2480, 5150-5250, 5250-5350, 5500-5700, 5745-5825
Label and Compliance Information
The final end product must be labeled in a visible area with the following information: Contains FCC ID: 2AG7C-R833.
Information on Test Modes and Additional Testing Requirements
If the host manufacturer installed this module with single modular approval, they should perform the test of radiated emission and spurious emission according to FCC part 15C, Part 15E, 15.209, and 15.207 requirements. The host can only be sold legally if the test results comply with these requirements.
Module User Manual
802.11a/b/g/n WiFi & BLE 4.2 Module 1T1R
It is a highly integrated single-chip 802.11a/b/g/n 1T1R WLAN, and an
integrated Bluetooth Low Energy 4.2 combo chip with USB 2.0 multi-function. It
combines a WLAN MAC, a 1T1R capable WLAN baseband, BT Protocol Stack, BT
Baseband, modem, and WLAN/BT RF in a combo chip. It provides a complete
solution for a high-performance integrated wireless LAN and Bluetooth
controller.
General QFN40 5 x 5 mm
802.11a/b/g/n 1T1R WLAN and Bluetooth Low Energy (BLE) 4.2 combo chip
Host Interface
- Complies with USB2.0 for WLAN and BT controller
- USB Multi-Function for both BT (USB function 0) and WLAN (USB function 1)
- USB LPM and USB Selective Suspend supported
Important Notice to OEM integrators
- This module is limited to OEM installation ONLY.
- This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b).
- The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations
- For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module’s intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). The Grantee will provide guidance to the host manufacturer for Part 15 B requirements if needed.
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or
co-location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the
end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains Transmitter Module FCC ID:2AG7C-R833 or Contains FCC ID:2AG7C-R833
”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
An intentional radiator shall be designed to ensure that no antenna other than
that furnished by the responsible party shall be used with the device. The use
of a permanently attached antenna or of an antenna that uses a unique coupling
to the intentional radiator shall be considered sufficient to comply with the
provisions of antenna requirements according to 15.203.
Federal Communication Commission Interference Statement This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC
Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Radiation Exposure Statement
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment.
The module must be installed in the host device.
This End equipment should be installed and operated with a minimum distance of
20cm centimeters between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
- (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
- (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
- (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01r01
List of applicable FCC rules
CFR 47 FCC Part 15 Subpart C and F has been investigated. It is applicable to
the modular transmitter
Specific operational use conditions
This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system.
Limited module procedures
Not applicable
Trace antenna designs
Not applicable
RF exposure considerations
The device has been evaluated to meet general RF exposure requirement. The
device can be used in mobile exposure condition with a minimum distance of
20cm centimeters between the radiator and your body.
Antennas
This radio transmitter FCC ID: 2AG7C-R833 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
Label and compliance information
The final end product must be labeled in a visible area with the following”
Contains FCC ID: 2AG7C-R833″.
Information on test modes and additional testing requirements
Host manufacturer installed this modular with single modular approval should
perform the test of radiated emission and spurious emission according to FCC
part 15C, Part 15E, 15.209, 15.207 requirement, only if the test result comply
with FCC part 15C, Part 15E, 15.209, 15.207 requirement, then the host can be
sold legally.
Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with the
module installed with all other applicable requirements for the system such as
Part 15 B.
Note EMI Considerations
Host manufacturers installed this modular with single modular approval should
be recommending “best practice” RF design engineering testing and evaluation
in case non-linear interactions generate additional non-compliant limits due
to module placement to host components or properties.
Host manufacture-installed this modular with single modular approval should be
recommended “For EMC/radio-parameter compliance purposes when an evaluation is
done by the grantee or host provider (see Clause IX in KDB Publication 996369
D01) and there are no additional emissions generated due
FAQ
Q: What is the host interface for this module?
A: The host interface for this module is USB 2.0.
Q: What are the dimensions of the module?
A: The module has dimensions of QFN40 5 x 5 mm.
Q: What is the maximum gain of the AntennaYJC-6N055-G09 for the 2.4G Band?
A: The maximum gain of the AntennaYJC-6N055-G09 for the 2.4G Band is 3.82 dBi.
Q: How far should I maintain a distance between my body and the device in mobile exposure conditions?
A: In mobile exposure conditions, maintain a minimum distance of 20 centimeters between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>