SohoTeco 1ET2-2R2 Electric Standing Desk Instruction Manual
- June 15, 2024
- SohoTeco
Table of Contents
SohoTeco 1ET2-2R2 Electric Standing Desk Instruction Manual
1ET2-2R2
min.27.9”-max.46.46”
100 kg(220 lbs)
Read the entire instruction manual before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings,
please contact your local distributor for assistance.
CAUTION: Use with products heavier than the rated weights indicated may
result in instability causing possible injury
Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by professionals. Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT:
Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, telephone your local distributor for a replacement.
MAINTENANCE:
Check that the bracket is secure and safe to use at regular intervals (at least every three months).
Checklist and installation
A x1
| 
B x1|
C x2
---|---|---
D x1|  E x1|
F x 2
G x 2| H x1| I x1
J x5|  K x1|  L x1
M x10
Screw List
M-A x1
|
M-B x8| M-C x8|
M-D x18|
M-E 2.5mm Allen Key|
M-F
5mm Allen Key|
Phillips Screw Driver
(Not include)
---|---|---|---|---|---|---
Tool
U x4|
V x8|
W x4
---|---|---
Checklist and installations
STEP : 1| 
| **Checklist
B x1
M-A x1
M-E 2.5mm
E x1
A x1
---|---|---
STEP : 2| 
|
STEP : 3| 
| Checklist
D x1
M-B x4
M-F 5mm
STEP : 4**| 
|
**Checklist
Fx2
M-B x4
M-F 5mm
**
STEP : 5| 
| Checklist
M X 10
STEP : 6| 
| **Checklist
C x2
M-C x8
M-F 5mm
STEP : 7**| 
|
Checklist
**N x1
Ux3
W x4**
STEP :8| 
Put the crews V into the hole of the tabletop be matched| **Checklist
V x4 Phillips Screw Driver
STEP : 9| 
| Checklist
Phillips Screw Driver
STEP : 10| 
| Checklist
V x4 Phillips Screw Driver
STEP : 11| 
| Checklist
J x2
Kx1
Phillips Screw Driver
M-D x6
STEP : 12| 
| Checklist
M-D x 10
Phillips Screw Driver
STEP : 13| 
| Checklist
H x1
M-D x2
Phillips Screw Driver
STEP : 14| 
| Checklist
I x1
STEP : 15| 
| Checklist
J x5**
INITIAL USE
Hold the “▼“ button until the desk reaches its lowest height, then release.
Hold the “▼”button again for about 10 seconds until the desk lowers a bit
more, then slightly rises and stops then release.
TECHNICAL SPECIFICATIONS
| Height Range | 27.9”(71cm) – 46.46”(118cm) |
|---|---|
| Travel Speed | 30mm(1.2”)per second |
| Weight Capacity | 100KG (220lbs) |
| Duty Cycle | 10%, Max. 2 mins on, 18 mins off |
3 Memory presets Soft Start/Stop Adjustable leveling
ADVANCED SETTING
Press the ” S ” button for 5 seconds until the LED flashes. The menu contains
7 items as the table below. Short press the “S” button to select the item
you’d like to set, then use the /▼“ buttons to adjust the value. Long press
the “S” button to save the setting and a progress bar will appear. “SUS” will
be displayed if it is saved successfully, and “FAL” will be displayed if it
fails. The menu will return to the display height automatically if no
operation within 10 seconds.
PROGRAMMING INSTRUCTIONS
MEMORY SETTINGS
Save up to four commonly used desk heights and recall them quickly.
- Use the UP or DOWN button to move the desk to the desired height.
- Press the “S”button.
- Press the “1, 2, or 3”button to assign the current height to a number on the handset.
- To bring the desk back to any of those assigned heights, press the numbered button.
HANDSET LOCK
The handset can be locked to prevent accidental activation or movement of the
desk and to prevent desk
VHWWLQJVIURPEHLQJDFFLGHQWDOO\FKDQJHGE\FKLOGUHQRUFRZRUNHUV
TO LOCK: Press and hold the “ ” and ” ” buttons simultaneously for 5
seconds until the LED reads “Loc”.
TO UNLOCK: Press and hold the
“UPµDQGµ’RZQµEXWWRQVVLPXOWDQHRXVO\IRUVHFRQGVXQWLOWKH/(‘VZLWFKHV from “Loc”to
the height display
Press” ” key till hear the second “di” sound (around 55 . use “A” or ” W ”
key| to choose (See the LED Flashes)| 1.Minimum Height| | 108CM / 43°| Press
°S” to fretum to the numerical display interface Set up SUS
---|---|---|---|---
Click “S” Key One Time| 69CM/27″
2.Maximum Height| | 116CM / 46″
Click “s” Key Two Times| 81CM/ 32″
3.Starting Height| | 0-30CM/0-11.8″
Click “S” Key Three Times
4.Upward Anti-Collision| |
-
PCO
shut down. -
PC1
-
PC2
-
PC3
The higher the number, the higher the sensitivity -
PC4
-
PC5
Click “S” Key Four Times
5.Downward Anti-Collision| |
-
DCO
shut down -
DC1
-
DC2
-
The higher the number, the higher the sensitivity
-
DC3
-
DC4-DC5
Click “S” Key Five Times
6.Sensor Anti-Collision| |
-
SSO
shut down -
SS1
-
SS2
-
SS3
The higher the number, the higher the sensitivity -
SS4
-
SS5
Click “S” Key Six Times
7.Display Unit| |
-
U-0
Change the numeric display to show heights in centimeters -
U-1
Change the numeric display to show heights in inches
Click “S” Key Seven Times
TROUBLESHOOTING
- If your desk does not respond when you try to raise it or lower it, or if the handset displays error messages,
check to make sure all the cables are secure(Legs to cables, cables to Control box). If the problem persists,
perform the reset procedure below.
RESET PROCEDURE
- Unplug the power cord and hold the S ” button on the Handset for 30 seconds.
- Plug the power cord backin.
- Hold the “W “ button until the desk reaches its lowest height, then release. Hold the “W”button again for about 10 seconds until the desk lowers a bit more, then slightly rises and stops then release.
- The handset will then display the current height, and you should be able to operate the desk.
- You may also need to do this if the desktop is ever unplugged or loses power.
If the error message persists after performing the Reset procedure, contact us or local distributors to get support.
| DESCRIPTION | CODE | TROUBLESHOOTING SOLUTION |
|---|---|---|
| Abnormal Standby Current | SO | Power on again. If the code persists, replace |
the Control Box
Abnormal Power Supply Board| SC1| Power on again. If the code sersists,
reolace the Control Box Power on again. If the code persists, replace the
Control Box
Abnormal Memory| SC2
Abnormal Sensor| SC3| Power on again. If the code persists, replace the
Control Box
Collision Protection by Sensor| R-2| The desktop will stop and retract 5cm(2″)
Overheated| HOT| Let the desk rest for 18 minutes
Communication Failure| R-5| Check the connection between Handset and Control
Box or replace Handset
Abnormal Voltage| R-6| Power on again. If the code persists, replace the
Control Box
Mechanical Failure| R-8| Perform Reset procedure. If the code persists,
replace the Leg
Rest not completed| RST| Perform Reset procedure
Short Circuit| EXO| Power on again. If the code persists, replace the Control
Box
Overload| EX1| Reduce the load on desk
Motor Open Phase| EX2| Perform Reset procedure. If the code persists, replace
the Leg
Wrong Running Direction| EX3| Perform Reset procedure. If the code persists,
replace the Leg
Collision Protection| EX4| The desktop will stop and retract 5cm (2″)
Motor Stalling| EX5| Perform Reset procedure. If the code persists, replace
the Leg
Disconnections of Motor Cable| EX6| Check the connection between leg and
control box
Remarks: X means 1(the first leg), 2(the second leg), 3(the third leg)
In the event of a power outage or if the power cord is unplugged, a manual
reset may be necessary (see Reset Instructions above)
This product is designed with a duty cycle of 10% (2 min. On, 18 min. off)
Keep Children away from electric height-adjustable desks, control units and
handsets.
There is a risk of injury and electric shock.
Do not open any of components: lifting columns, control box, or handset. There
is a danger of electric shock.
Keep all electrical components away from liquids
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>