LURACO L0903A iFill 5 Smart Spa Overflow Control System User Manual
- June 12, 2024
- LURACO
Table of Contents
L0903A infill 5 Smart Spa Overflow Control System
User Manual
infill 5 Intelligent Spa Control System
MODEL L0903A
L0903A infill 5 Smart Spa Overflow Control System
When using electrical equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury. Safety precautions are as follows:
- Read and follow all instructions before using the equipment.
- Keep the cord out of heavy traffic area. To avoid fire hazard NEVER put the cord under rugs or near heat generating devices.
- Always turn off the equipment before servicing.
- Do not drop or insert any object into any openings.
- Do not operate any equipment with damaged parts.
- This system is for indoor use only.
- Do not attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty.
- As a condition of acceptability UL requires that this product be installed over a non-combustible surface; if this product is installed over a combustible surface, a non-combustible layer must be installed between the device and the surface.
- Any other use not recommended by the manufacturer may result in electrical shock or injury.
After reading this owner’s guide, if you have any questions or comments, please call 817-633-1080 or contact our technical support department at support@luraco.com or visit our website at www.luraco.com for more information
PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
FEATURES and OPERATIONS
iFill 5 Features
- Complete spa controller with intelligent automatic fill features.
- Digital water temperature and session elapsed time display.
- Volume setting from 1 to 10 gallons.
- Can be used with or without disposable liners.
- 3 switched and 1 continuous outlet.
- Drain pump-controlled outlet with timer.
- Heavy duty industrial graded brass water valve and flow sensor package.
- Can be operated in both automatic or manual modes.
- Built-in 1-hour timer.
- Reliable, simple and easy to use.
- 120VAC, 60Hz (2 Amps max per outlet).
- UL Recognized
Installation Guide
I) Overall System Integration
ATTENTION: BACKFLOW “PREVENTERS ARE” REQUIRED FOR EVERY SPA CHAIR. THEY MUST BE INSTALLED ON BOTH HOT AND COLD-WATER LINES TO AVOID LOSING HOT WATER FROM ONE CHAIR TO ANOTHER.
II) System Installation
Follow the steps below for iFill 5 installation
a) Connect the Flow Sensor/Water Valve Package to the output of water
mixer/faucet. Be sure the water flow direction is correct.
b) Connect the Control Keypad and Flow Sensor/Water Valve Package to Master
Box
Automatic Fill Volume Setting:
The volume of each Auto infill can be set by the knob located next to the
power cord on Master box.
Depending on the knob position, water valve shuts off when water volume
reached the set value.
How To Change the Temperature Unit (Fahrenheit or Celsius):
Be sure all buttons on keypad are off, press and hold the END/DRAIN button for
5 seconds until F or C is displayed on the keypad.
III) How to operate the if ill 5 (Be sure that the faucet is open)
ATTENTION: BEFORE PRESSING AUTO infill BUTTON. BE SURE PREVIOUS SESSION
IS COMPLETE AND DRAIN OUT WATER IN THE BASIN. TO UNLOCK THE AUTO BUTTON, PRESS
END BUTTON
– Press the Auto/infill button to turn On or Off the Automatic fill.
– Press the JET button to turn On or Off the JET and color light manually (1
hour timer)
– Press the Wash button to turn On or Off the water manually (5 minute safety
timer)
– Press End/Drain button to end the session and unlock the Auto fill button.
This button will also turn on the drain pump.
Understanding The Display Screen
IV) How to reboot the iFill 5
Please follow the steps below
– Completely drain all water from the tub.
– Unplug the Masterton power cord from the power outlet.
– Wait about 5 seconds and then plug power cord back into the power outlet.
WARRANTY INFORMATION
One (1) YEAR LIMITED WARRANTY
- This Warranty applies only to the original purchaser of this product.
- This Warranty applies ONLY to repair or replacement of any supplied or manufactured parts of this product. The warranty does not cover normal wear, coating, dropped or abused units or any related shipping costs.
- Unless otherwise proscribed by law, Lirico shall not be liable for any personal injury, property or any incidental or consequential damages of any kind resulting from malfunctions, defects, misuse, improper installation or alteration of this product.
Attention: Any modification to the product will void the warranty
Important Instructions
If you need to send a unit to Lirico for repair, please follow the steps
below.
- Call 800-483-9930 or 817-633-1080 to get a case number.
- Carefully pack the item in its original carton or other suitable container to avoid damages during shipping.
- Before packing your unit, be sure to enclose:
• Your name with full shipping address and telephone number.
• A dated receipt for PROOF OF PURCHASE.
• The case number that will be given to you in Step 1.
• Include a detailed description of the problem you are having.
• All shipping costs must be prepaid by the sender.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>