DYNOJET PC6-20016 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for PC6-20016
Model coverage: 2006-2020 Suzuki M109R / C109R
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
1 ZIP TIE
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION.
THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map| (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
---|---
Shifter| (Input 1 or 2) Used for clutch-less full-throttle upshifts. Insert
the wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed| Not needed on Harley applications as the speed signal wire is built
into the main wiring harness of the PC6.
Analog| This input is for a 0-5v signal such as engine temp, boost, etc. Once
this input is established you can alter your
fuel curve based on this input in the Power Core software.
Launch| You can connect a wire to either Input 1 or Input 2 and then the other
end to a switch. This switch when engaged (continuity) will only allow the RPM
to be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the
unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tightens the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and both side covers.
-
Remove the fuel tank.
-
Remove the air box.
There are several hoses going into the air box. We recommend referring to the service manual for proper removal and installation. -
Route the wiring harness from the PC6 behind the left-hand side of the frame and go towards the throttle bodies.
-
Unplug the stock wiring harness from each fuel injector.
-
Plug the connectors from the PC6 in-line with the fuel injectors and the stock wiring harness connectors.
ORANGE – cylinder 1- front
YELLOW- cylinder 2 – rear -
Using the supplied zip-tie, secure the PC6 wiring harness to the high-pressure fuel tube between the throttle bodies such that the PC6 harness will not interfere with reinstalling the intake plenum or interfere with throttle blade movement.
-
Unplug the Throttle Position Sensor connector.
This connector is located on the right-hand side of the throttle bodies and is GREY in color. Do NOT unplug the BLACK 3-pin connector for the upper secondary throttle plates. -
Plug the connectors from the PC6 in-line with the TPS and the stock wiring harness.
-
Route the ground wire from the PC6 thru the front hole in the battery box.
-
Secure the ground wire from the PC6 wiring harness with the small ring lug to the negative (-) terminal of the bike’s battery.
FOR THE M109R -
Install the PC6 to the face of the metal bracket under the left-hand side cover using the supplied Velcro.
Make sure to clean both surfaces with the alcohol swab before attaching the Velcro.
FOR THE
C109R -
Install the PC6 to the face of the ECU using the supplied Velcro.
Make sure to clean both surfaces with the alcohol swab before attaching the Velcro. -
Reassemble the bike.
When reinstalling the intake plenum, be sure the rubber boots are completely over and around the top of the throttle bodies. This piece can be very diffi cult going back on.
Download the latest map files from our website at
dynojet.com/tunes.
Optional inputs:
Speed input – PINK wire of BLACK 3-pin connector.
The sensor is located behind the left side cover near the ignition switch.
Temperature input – BLUE/BLACK wire from temp sensor behind right side dummy
air box cover.
12v source for Auto-tune – BROWN wire in 6-pin connector for the tail light.
Located under the driver seat.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
800-992-4993
DYNOJET.COM
© 2006-2022 DYNOJET RESEARCH
ALL RIGHTS RESERVED
PC6-20016
06-20 SUZUKI M109/C109
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>