BARCO UDX 4K32 Projector User Guide

UDX 4K32 Projecto

Quick Start Guide

Download Product Manual
Product manuals and documentation are available online at www.barco.com/td/R9008600
Registration may be required; follow the instructions given on the website.
IMPORTANT!
Read Installation Instructions before connecting equipment to the mains power supply.

Install Lens

!! ONLY USE TLD+ Zoom Lenses !!

1. Place the primary lens lock in “unlock” position. Handle (ref. 1) towards electrical socket (ref. 3).

2. If present remove the plastic protection cover from the lens holder opening.
   3 . Check if the secondary lens lock stands in the “unlock” position (ref. 2) .

3. Gently insert the lens. Ensure the lens connector matches the electrical socket on the lens holder.

4. Insert the lens until the connector seats into the socket.
   – The secondary lens lock (ref. 2) makes an audible clicking sound when latching.
   – Do not release the lens yet, keep pushing the lens against the front plate!

5. Secure the lens in the lens holder by sliding the primary lens lock handle into the “locked” position.

6. Check if the lens touches the front plate of the Lens Holder.

7. Check if the lens is really secured by trying to pull the lens out of the lens holder.

Connect power
Ensure that the power is properly connected to the power input.
(120-160V / 200-240V [+/-10%, reduced light output] )

Startup

1. Power on. Turn the mains switch to on ( I ).
   – Start up sequence starts. Backlight of the Power on/off button flashes WHITE.
   – When start up sequence is finalized the Power on/off button lit WHITE.

2. Press the Power on/off button.
   – The backlight of the Power on/off button changes from WHITE to BLUE.
   – Local LCD displays a start up screen.

Adjust

1. Adjust the lens settings by pressing the LENS button or via the direct lens keys on the RCU.
   Select the “Greenfocus” test pattern to adjust the lens.
   TIP: Press star button (*) to activate test pattern![BARCO UDX 4K32 Projector

• assembly 4](https://manuals.plus/wp-content/uploads/2024/02/BARCO-UDX-4K32 -Projector-assembly-4.png)

  2. Orientation of the unit is set as standard in table front projection mode. Change the projector set up in the ALIGNMENT > ORIENTATION menu.
     

  3. For Advanced adustments like Warping, Light management, etc. see User Guide of the projector.

Connect and Select source

1. Connect available sources to the appropriate input ports.
2. Select connected source: Image of selected input appears.
   – The LED of the selected source lit up GREEN.
   – The yellow LED indicates if sync/signal is present.

Switch off

1. Press the Power on/off button for three seconds.
2. Wait until the after-cooling cycle is finished (approximately 30 sec.)
3. Turn the mains switch to off (’0’).
4. Unplug the power cord from the projector.

**** Precautions

• Remove the lens before transporting the projector.
• First switch the projector to Standby mode and wait until After Cooling is finished to switch off the main power.
• Ensure the projector is operating with clean filters.
• Do not block the ventilation in and outlets.
• External laser light can cause severe damage to the DMD. This damage is not covered by warranty.

Local Keypad

RCU buttons

Communication Panel

Venues & Hospitality Input (V&H)

Virtual & Augmented Reality Input (V&AR) (Optional)

Button Backlight Status

LED Status

Support
Websitewww.barco.com/esupport
Tel.:
– USA +1 866 374 7878
– EMEA +32 56 36 8019
– APAC +86 400 88 22726

Documents / Resources

| BARCO UDX 4K32 Projector [pdf] User Guide
UDX 4K32 Projector, UDX, 4K32 Projector, Projector
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>