BARCO G62 Replacement Set Dust Filter Instruction Manual

BARCO G62 Replacement Set Dust Filter

Changes

Barco provides this manual ‘as is’ without warranty of any kind, either expressed or implied, including but not limited to the implied warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or the program(s) described in this publication at any time without notice.

This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this publication; these changes are incorporated in new editions of this publication. The latest edition of Barco manuals can be downloaded from the Barco web site www.barco.com.

Copyright ©

All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or stored in a retrieval system without the prior written consent of Barco.

Guarantee and Compensation

Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing faults Barco must be informed immediately in writing of any complaints.

The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning, at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.

If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributed to programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normal maintenance are not subject to the guarantee provided by Barco either. The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the customer.

Patent protection

Please refer to www.barco.com/about-barco/legal/patents.

Trademarks

Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders. All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for the products or their manufacturers.

Introduction

Purpose of the dust filter kit

The dust filter kit is:

• compatible with G60 and G62 projectors,
• highly recommended in areas with polluted air,
• designed to be mounted on the projector externally.

CAUTION: The filters are not washable and are designed for disposable use only

Projector usage after filter installation

To ensure sufficient air flow into the projector for cooling, take care to:

• Raise the projector’s feet to the highest position possible to ensure continued airflow beneath the bottom filter.
• Select High Altitude Mode for the Cooling Mode to enable maximum fan speed.

Take care not to use the projector on too high ambient temperature conditions:

Altitude (m)| Ambient temperature without filter| Ambient temperature with filter
---|---|---
0-750| 0-40°C| 0-35°C
750-1500| 0-35°C| 0-30°C

1500| 0-30°C| 0-25°C

Dust filter kit package overview

Contents of the dust filter kit

• Left filter holder (reference 1)
• Left filter (reference 2)
• Bottom filter holder (reference 3)
• Bottom filter (reference 4)
• Three Phillips PH2 screws
  

Installation procedures

Installing the left dust filter

Required tools

Phillips screwdriver PH2

Required parts

• Left dust filter holder
• Left dust filter
• Two Phillips PH2 screws

How to install the left dust filter

1. Insert the filter in the filter holder.
   Caution: Make sure the soft side of the filter faces the grid of the filter holder.
   

2. Remove the second and fourth screws (reference 1) on the left side of the projector as illustrated in the following image.
   

3. Attach the filter assembly onto the projector using the four clips (reference 2) positioned at the bottom of the filter holder.
   Tip: Ensure that the filter assembly is properly aligned by verifying that the top screw holes of the filter holder match with the screw holes on the projector.
   

4. Secure the filter assembly to the projector with two Phillips PH2 screws (reference 3).
   

Installing the bottom dust filter

Required tools

• Phillips screwdriver PH2
• Clean blanket

Required parts

• Bottom dust filter holder
• Bottom dust filter
• Phillips PH2 screw

How to install the bottom dust filter

1. Insert the filter into the filter holder.
   Caution: Make sure the soft side of the filter faces the grid of the filter holder.
   

2. Turn the projector upside down to access the bottom of the projector.
   Caution: Use a blanket to not damage the top cover of the projector.
   

3. Place the filter assembly (reference 1) onto the air inlet as illustrated in the following image. Hook the filter assembly to the air inlet with the clips ( reference 2 ).
   

4. Secure the filter assembly to the projector by tightening a Phillips PH2 screw (reference 3) into the designated screw standoff.
   

Filter replacement

 It is recommended to replace the filter every six months.

Replacing the left dust filter

Required tools

Phillips screwdriver PH2

Required parts

• Left dust filter holder
• Left dust filter
• Two Phillips PH2 screw

How to replace the left dust filter

1. Remove the two screws (reference 1) securing the filter assembly to the projector. Use a Phillips PH2 screwdriver.
   

2. Detach the filter assembly from the projector, pushing slightly up to release the clips on the bottom.
   

3. Remove the dirty filter from the filter holder and insert the new filter (reference 2).
   Caution: Make sure the soft side of the filter faces the grid of the filter holder.
   

4. Attach the filter assembly onto the projector using the four clips (reference 3) positioned at the bottom of the filter holder.
   Tip: Ensure that the filter assembly is properly aligned by verifying that the top screw holes of the filter holder match with the screw holes on the projector.
   

5. Secure the filter assembly to the projector with two Phillips PH2 screws (reference 4).
   

Replacing the bottom dust filter

Required tools

• Phillips screwdriver PH2
• Clean blanket

Required parts

• Bottom dust filter holder
• Bottom dust filter
• Phillips PH2 screw

How to replace the bottom dust filter

1.  Turn the projector upside down to access the bottom of the projector.
   Caution: Use a blanket to not damage the top cover of the projector.
   

2. Remove the screw (reference 1) securing the filter assembly to the projector. Use a Phillips PH2 screwdriver.
   

3. Remove the filter assembly (reference 2) from the air inlet using the clips (reference 3) as illustrated in the following image.
   

4. Remove the dirty filter from the filter holder and insert the new filter (reference 4).
   Caution: Make sure the soft side of the filter faces the grid of the filter holder.
   

5. Place the filter assembly (reference 5) onto the air inlet as illustrated in the following image. Push towards the front to hook the filter assembly to the air inlet with the clips (reference 6).
   

6. Secure the filter assembly to the projector by re-tightening the Phillips PH2 screw into the designated screw standoff.
   

Customer Support

www.barco.com

References

• Inspired sight and sharing solutions - Barco
• Patents - Barco

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>