BIXOLON SPP-R220 Series 1×12 Guitar Speaker Cabinet User Manual

BIXOLON SPP-R220 Series 1×12 Guitar Speaker Cabinet

Manual Information

This user manual contains basic information for product usage as well as for emergency measures that may be required.

• The following separate manuals provide more detailed content on various technological issues and areas.

Software Manual

These manuals provide information for development. Please refer to each manual for more information.

• Windows Driver Manual
• OPOS Driver Manual
  • OPOS Installation manual
  • OPOS Setup Utility guide manual
  •  OPOS Application programming guide manual
• JPOS Driver Manual
  • JPOS Installation and Configuration Utility guide manual
  • JPOS Application Programming Guide manual
• Windows SDK Manual
• Android SDK Manual
• iOS SDK Manual
• Unified Mobile Utility Manual
• Android Utility Manual
• Net Configuration Tool Manual

Bluetooth & Wireless Manual

• Bluetooth: This manual describes how to connect terminals (PDAs, PCs, etc.) with Bluetooth functionality.
• Wireless LAN : This manual describes how to connect wireless LAN in infrastructure or ad-hoc mode.

Commands Manual

This manual provides information on the protocol and functions of the control commands that can be used with this product.

Code Pages Manual

This manual provides information on each character code page that can be used with this product. We at BIXOLON maintain ongoing efforts to enhance and upgrade the functions and quality of all our products. In following, product specifications and/or user manual content may be changed without prior notice.

Safety Precautions

In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage.

WARNING

Violating following instructions can cause serious injury or death.

CAUTION
Violating following instructions can cause a slight wound or damage to the appliance.

Battery Safety Precautions

Make sure to review the user manual carefully prior to product use.
Neglecting to heed the following instructions can result in battery overheating, combustion, explosion, damage and/or decline in performance and product life.

Danger

1. Do not allow water, seawater or moisture to enter or leak into the battery. If the safety mechanism within the battery becomes oxidized, the battery may overcharge with abnormal electrical current and/or voltage so that it may overheat, ignite and/or explode.
2.  Do not place the battery near open flames or heating devices, such as stoves. Exposure to excessive heat may cause damage to the resin case and/or insulating materials, thus causing a short circuit within the battery that may result in battery overheating, combustion, and/or explosion.
3. Charge the battery only with the exclusive charger specified (optionally provided) by BIXOLON. The use of an incorrect charger may result in overheating, combustion and/or explosion of the battery.
4. Charging the battery with a modified charger may result in overheating, combustion and/or explosion of the battery by abnormal chemical reaction caused by incorrect polarity.
5. Do not directly connect the battery to an electrical power outlet not specified by BIXOLON or an automobile’s cigarette lighter jack. Doing so may result in overheating, combustion and/or explosion of the battery by over-current and/or over-voltage.
6. Do not heat the battery or place it near a fire. Doing so may melt insulation materials, damage the safety mechanism/equipment, and/or ignite the electrolytic solution. There is a potential risk of battery overheating, combustion, and/or explosion.
7. Do not reverse the connection of (+) and (-) electrodes of the battery. Charging the battery in reverse polarity may produce an undesired chemical reaction inside the battery cell, causing unexpected behaviour during discharging such as overheating, explosion, or fire.
8. Do not allow the battery’s (+) or (-) pole to come into contact with any metal. In addition, do not carry or store the battery with metallic items, such as necklaces and hairpins. Doing so may cause a short circuit of the battery generating an over-current. There is the potential risk of overheating, igniting and/or exploding the battery or overheating the metallic items, such as necklaces, hair pins etc.
9. Do not throw the battery or subject it to strong shock. If the safety mechanism in the battery is damaged, the battery may be overcharged and, consequently, an adverse chemical reaction may be generated in the battery. There is a potential risk of battery overheating, combustion, and/or explosion.
10. Do not pierce the battery with a pointed object, such as a nail or awl, or strike with a heavy object, such as a hammer, and take care not to step on the battery. There is a potential risk of battery overheating, combustion, and/or explosion caused by an internal short circuit.
11. Do not solder the battery directly. Doing so may melt the insulating materials and/or damage the safety mechanism or safety equipment, resulting in battery overheating, combustion, and/or explosion.
12. Do not disassemble and/or modify the battery. The battery contains safety equipment and a safety mechanism to prevent danger. There is a potential risk of overheating, combustion, and/or explosion caused by disassembly.
13. Do not charge the battery near open flames and/or under direct sunlight. Because exposure to high temperatures triggers the operation of the safety mechanism, the battery may not charge or may overcharge due to the destruction of the safety mechanism. There is a potential risk of overheating, combustion, and/or explosion.
14. Do not expose the battery to high temperatures over 60 C, and do not use or store it in a hot or humid place.
15. Do not use the battery if it is damaged or the exterior is deformed due to external shock or if it is swollen.

Warning

1. Do not place the battery within the reach of small children to prevent any swallowing accidents. If a small child has swallowed the battery, consult a physician immediately.
2. Do not place the battery in a microwave oven and/or high-voltage appliance. Doing so can cause rapid overheating and/or destruction of the sealing, resulting in battery overheating, combustion, and/or explosion.
3. Do not combine and use any battery of different capacity and/or type with the primary battery. Doing so can cause excessive electrical discharge during use or excessive charging during charging, resulting in an abnormal chemical reaction within the battery that can cause battery overheating, combustion, and/or explosion.
4. If during battery usage, storage, or charging, a strange odour or conditions differing from the normal, such as overheating, color changes, warping, etc., are detected, remove the battery from the product or charger and discontinue use. Continued use may cause battery overheating, combustion, and/or explosion.
5. When recharging, if the battery is not charged after the normal fixed charging time, discontinue charging. Continued charging can result in battery overheating, combustion, and/or explosion.
6. If the battery appears to be coated with condensation or emits a strange odour, immediately place it far away from any heat source. The condensation may be caused by a leak of electrolytic solution that can ignite to cause battery combustion and/or explosion.
7. If the battery is leaking electrolytic solution and any of the solution enters the eyes, immediately wash out with clean water, and then consult a physician to receive treatment. Neglecting to do so can cause permanent eye injuries.

Caution

1. Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight, such as within an automobile. Doing so can cause battery overheating and/or combustion. In addition, battery performance and product life may be reduced.

2. The battery contains a safety mechanism to prevent danger. Do not use the battery in a location that is prone to static electricity (above the amount covered by the manufacturer’s product warranty) that can cause damage to this safety mechanism. Damage to the safety mechanism can result in battery overheating, combustion, and/or explosion.

3. The temperature ranges for battery usage are as follows. Any usage outside of these ranges can result in battery overheating and/or damage. In addition, battery performance and product life may be reduced.

4. Charging: 0 ~ 40 oC

5. Product Usage: -20 ~ 60 C

6. Storage: -20 ~ 60 oC (30 days)

7. Long-Term Storage: -20 ~ 40 oC (90 days)

8. Please review the exclusive charger manual carefully for charging instructions.

9. If you observe any abnormal symptoms, such as a strange smell and overheating, on first use after purchasing the product, contact your local dealer immediately.

10. If a child must use the battery, the child’s parent or legal guardian should clearly explain the instructions from the user manual prior to use. In addition, the parent or legal guardian should periodically confirm that usage is being conducted in accordance with user manual instruction during use.

11. Store the battery in a location that is out of the reach of small children. During usage, make sure to also place the charger and/or product out of the reach of small children.

12. If the battery is leaking electrolytic solution, and the solution comes in contact with the skin or clothing, immediately wash thoroughly with clean water. Contact with skin can result in skin disorders.

13. Make sure to review the user manual and precautions carefully prior to use.
    In addition, after carefully reviewing the user manual and precautions, place them in a secure location for future reference when needed.

14. There is a risk of explosion when replacing with an incorrect battery. Only exchange it for another one of the same or equivalent model specified by BIXOLON. Insulate the used battery by attaching insulation tape to its port, and then dispose of the battery according to local regulations.

15. If using the printed side of preprinted paper, this may cause malfunction.

Recommended

1. Review the user manual for instructions concerning the insertion/removal of batteries into/from the product.
2. The battery shipped with the product is partially charged, and it is good for checking the operation of the equipment. Charge the battery first with the supplied charger if the equipment does not work or long hours of operation are required.
3. To avoid improper use of the battery, review the product user manual carefully.
4. Do not charge the battery for long times in excess of the normal charging time indicated in the user manual.
5. If the battery is not to be used for a long period of time, remove it from the product and store in a location with low humidity. If the battery is stored while still inserted in the product in a highly humid location, oxidization may occur along with a decline in battery performance.
6. Turn off the power after using the equipment. Otherwise, the performance of the battery will be degraded over time.
7. The battery may fail to charge if it is not used for a long period of time. Charge the battery with the supplied charger at least once every six months if the equipment is not used for a long time. Leaving the battery for a long time without charging may degrade the performance of the battery or cause system trouble.
8. If the battery terminal is contaminated, clean the contact with a dry cloth before using it. Using the battery with contaminated contacts may cause problems when supplying power to the equipment or charging due to irregular electric contact.
9. Each battery has a life cycle. If the usage time of the product is shortened, replace it with a new battery. Insulate the used battery by attaching insulation tape to its port, and then dispose of the battery according to local regulations.

Other Precautions

The copyright for this user manual and various other manuals is property of BIXOLON Co., Ltd. Any copying or conversion into electronic firm and saving of this material without the express written permission of BIXOLON Co., Ltd. is strictly prohibited.
Use of the information contained in this manual is not subject to any patent liability. This manual has been prepared with utmost care and attention to detail but may contain certain errors and/or omissions. BIXOLON Co., Ltd. is not legally liable for any damages resulting from the use of the information in this manual. BIXOLON Co., Ltd. and its affiliates are not legally liable for any damages, loss, costs, and/or expenses that result from the breakdown, malfunction, and/or misuse of the product due to violation or neglect of the operation and maintenance information and instructions provided by the BIXOLON Co., Ltd., as well as from the unauthorized alteration, repair, and/or modification of the product by the user and/or third party. BIXOLON Co., Ltd. is not legally liable for any damages and/or issues resulting from the use of options and/or parts that are not authentic BIXOLON products or authorized products.

Content Confirmation

The following items should all be contained in the printer package. Contact the dealer from which the purchase was made if any item is damaged and/or missing.

Product Part Names

Front

Rear

Installation & Usage

Battery Installation

1. Insert the battery on the rear side of the printer, aligning the battery hook properly.
2. Push the battery into the slot until a snapping sound is heard.v

NOTE As the battery is not charged at the time of purchase, charge the battery prior to product use. (Use the battery charger)

Battery Charging

Using Battery Charger

1. Turn off the printer power.
2. Connect the power cord ② to the battery charger ①, and then connect AC power.
3. Open the external interface cap in the direction of ③.
4. Connect the battery charger to the power connector.

CAUTION
The printer may incur serious damage if the battery charger provided by BIXOLON is not used. BIXOLON is not legally liable for any such damages. (The voltage and electrical current specifications of the printer and battery charger must match.)
WARNING
Turn off the power before charging the battery for the printer.

Using Single Battery Cradle (Optional)

1. Connect the power cord ② to the battery charger ①.
2. Connect the battery charger ① to the power connector of the single battery cradle ③.
3. Plug the power cord ② into an electrical outlet.
4. Insert the battery ④ into the single battery cradle ③ until a snapping sound is heard.

Using Vehicle Charger (Optional)

1. Turn off the power to the printer.
2. Connect the vehicle charger ① to your car’s cigarette lighter jack.
3. Open the external interface protection cap in the direction of ②.
4. Connect the vehicle charger to the power connector.

CAUTION
The printer may be seriously damaged if a battery charger not provided by BIXOLON is used. BIXOLON is not liable for such damage.
WARNING
Turn off the power before charging the battery for the printer.

Using Single Docking Cradle (Optional)

1. Turn the printer off.
2. Slide the printer in the single docking cradle as shown in the picture.
3. Push the printer in until a clicking sound is heard.
4. Charging will begin when the printer is installed.
5. Pull out the printer to separate it.

CAUTION
Please be sure to use the battery with external power contacts.

Using Quad Battery Charger / Quad Docking Cradle (Optional)

Connecting the cables

1. Connect the power cord to the adaptor, and Connect the adaptor to the power connector of the quad battery charger /quad docking cradle.
2. Plug the power cord into a power Outlet. Input power is 100 ~ 240VAC, 50/60Hz, 1.0A.
3. When the power is supplied, the yellow, green and red lamps are on for three seconds and do the self-test.

WARNING
Use only the designated AC/DC adaptor. (12VDC, 3A)

Charging Battery (Printer)

1. Fasten batteries via the battery hooks into the quad battery charger as shown above.
2. Push the battery in until a snapping sound is emitted.
3. Charging begins as soon as the battery is completely inserted. (Batteries are charged to 8.4VDC, 0.8A.)
4. Push the hook and pull up to extract the battery.

1. Turn the printer off.
2. Slide the printer in the quad docking cradle as shown in the picture.
3. Push the printer in until a clicking sound is heard.
4. Charging will begin when the printer is installed.
5. When charging is complete, Pull out the printer to separate it.

CAUTION
Please be sure to use the battery with external power contacts.

NOTE
Battery charging status descriptions are as follows.

2.5 hours

Green Lamp Blinking| Over 80% Charged
Green Lamp On| Fully Charged
Red Lamp Blinking| Error Replace or Reinstall Battery

CAUTION

1. If the red lamp of the charger blinks, install the battery again.
2. If the red lamp continues to blink despite several attempts (4 ~ 5 times) to install the battery, contact your local dealer.
3. The charging time may vary depending on the type of charger or ambient temperature.

Paper Installation

1. Press the Open button to open the paper cover.
2. Insert the paper as shown in the image. (Remove any remaining core of a fully used paper roll.)
3. Take care to align the paper correctly
4. Pull the paper out as shown in the image and close the paper cover.
5. Tear off any excess paper in the direction of the side of the printer

Using Belt Clip

1. Insert the screw of the belt clip to the belt clip mounting hole.
2. Fasten the screw of the belt clip with an object like a coin as shown in the picture.(Be careful to fasten in the correct direction.)
3. Insert the clip to the belt.

Using Belt Strap (Optional)

1. Insert the belt strap screw into the belt strap hole.
2. Use a coin to tighten the belt strap screw as shown in the image.
3. Undo the belt strap Velcro.
4. Fasten the belt strap to a belt.
5. Close the Velcro as shown in the image.

Using Case (Optional)

1. Open its top cover.
2. Insert the printer in the case in the direction shown in the picture.
3. Close the Velcro.
4. Attach it to the belt using the clip on the back of the case.

Note

The clip of the protective case can be rotated in two steps of 30° for each step (up to 60°)

Using Control Panel

Power Button

This button is used to turn the printer on and off.

1. When the printer is off, press this button for approximately 2 seconds to turn on the power.
2. When the printer is on, press this button for approximately 2 seconds to turn off the power.

Paper Feed Button

To feed paper manually, press this button. In addition, self-testing and Hexadecimal Dumping can be done.v

1. Refer to “4. Self-Test” for self-test information.
2. Refer to the service manual regarding Hexadecimal Dumping.

Battery Status LED (Blue or Red)

1. If the blue LED is lit, the battery is fully charged.
2. If the blue LED is blinked, the battery is half charged.
3. If the red LED is blinked, the battery must be charged or replaced.

Error LED (Left-sided)

1. If the red LED is lit, the paper cover is open.
2. If the red LED is blinking, either the paper has been fully used or the print head is overheated. (Replace the roll of paper or turn off the printer for at least 10 minutes.)
3. If the red LED continues to blink, it may indicate a more serious problem with the product. Call your authorized service dealer.

Bluetooth & Wireless LAN LED (Right LED)

1. When using Bluetooth If the printer is ready for wireless communication with any Bluetooth, the green LED as well as the battery status LED is turned on.
2. When using wireless LAN The right indicator shows the signal strength from wireless LAN. The green LED blinks for acceptable signal strength while the green LED blinks for weak signal strength.

In power save mode, only the Status LED is lit.

NOTE
The power saving mode is activated after the first communication, with the default time interval being 10 seconds.

Using MSR

1. Insert the card as shown in the image and swipe in the direction of the arrow.(This can be done in both directions)

NOTE
If the card does not register, first check to see if it is properly aligned. When swiping the card, the recommended swiping speed is 100 ~ 1200 mm/sec.

Recommended Papers

• Receipt paper
  • TF50KS-E (Paper Thickness: 65μm): Nippon Paper Industries Co., Ltd.
  • PD 150R (Paper Thickness: 75μm): New Oji Paper Mfg. Co., Ltd.
  • PD 160R (Paper Thickness: 75μm): New Oji Paper Mfg. Co., Ltd.
  • P350 (Paper Thickness: 62μm): Kansaki Specialty Paper, Inc. (USA)
  • P220AG (Paper Thickness: 65μm): Mitsubishi Paper Mills Limited
  • P220A (Paper Thickness: 65μm): Mitsubishi Paper Mills Limited
  • F5041 (Paper Thickness: 65μm): Mitsubishi HitecPaper Flensburg Gmbh
• Linerless paper: T6087 (Paper Thickness 76μm), Blumberg GmbH & Co. KG

Self-Test

Run the self-test when first setting the printer or when encountering a problem, and check the following.
Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch Settings If no issue is found with the printer after running the self-test, examine the other devices or peripherals and software. This function is independent of such other devices and

Self-Test Instructions

1. Turn the printer power off and close the printer paper cover.
2. Press and hold the paper feed button and power button simultaneously to turn on the printer.
3. After printing begins, release the two buttons.
4. To view a printout of the ASCII pattern, press the paper feed button once more.
5. After the ASCII pattern is printed out, the self-test is automatically terminated. software.

Self-Test Sample (For Bluetooth)

Self-Test Sample (For Wireless LAN)

Label Printing Function

Label Function Setting

Label paper and black mark paper are available at the label mode.

Setting Operations

1. Turn on the printer power.
2. Open the paper cover and press and hold down the paper feed button for longer than two seconds.
3. After the buzzer tone is emitted, insert paper and close the cover.
4. Repeat the steps above to return to receipt mode.

Setting Via Memory Switch

1. Please refer to the memory switch changing section of the Commands Manual.

Auto Calibration Function

The label printing function requires the recognition of label paper gaps and black mark paper black bar in order to print. If label paper gaps are not properly recognized, use the auto calibration function.

Auto Calibration Instructions

1. Turn the printer power off while in label print mode.

2. Press and hold down the paper feed button and then press the power button.

3. After the following printout is outputted, press the power button to perform auto-calibration.
   Select the mode
   Auto Calibration: Power Button Self Test: Feed Button

4. One page of label paper is outputted when performing auto-calibration.

Peripherals Connection

This product can communicate with other devices via wireless communication and cable.

Bluetooth & Wireless LAN Connection

1. The printer can be connected to devices equipped with Bluetooth communication capacity (PDAs, PCs, etc.).
2. Use the Bluetooth connection function supported by the device to connect to the printer. The NFC tag built into the printer enables automatic pairing with devices.

NOTE
Tap your host device to the logo on the side of the printer for NFC auto pairing
NOTE
The device must support NFC Auto Pairing. It may display a message that the device cannot be connected as NFC Auto Pairing is supported up to the B/T pairing and the devices must be connected manually, but this is normal.

1. The printer can be connected to other stations, such as PDAs and PCs supporting wireless LAN communication in Ad-hoc mode, Soft AP mode and AP in Infrastructure mode.

NOTE
Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection. You can check the bluetooth environment  (authentication, encryption, connection mode) and the wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page.

Interface Cable Connection

1. Open the Interface Cap ①.

2. Connect the interface cable (optional) ② to the cable connector of the printer.
   NOTE Use only the cables (optional) provided by BIXOLON. (USB)

3. Connect the interface cable to the USB port of the device (PDAs, PCs, etc.).
   NOTE The interface cable that can be connected with the printer is available in USB type. Refer to the service manual for detailed interface cable specifications.

Printer Cleaning

If the interior of the printer is dusty, print quality can decline. In such a case, follow the instructions below to clean the printer.

1. Open the paper cover and remove the paper, if present.
2. Clean the printhead (A) using the cloth or cotton swab soaked in alcohol for medical.
3. Using the cloth or cotton swab soaked in alcohol for medical, remove the paper dust from the black mark sensor (B). (Sensor could be located in the middle or on left or on right)
4. Do not use the printer for one to two minutes after cleaning until the alcohol for medical has completely evaporated and dried.
5. Insert the paper and close the paper cover.

Caution

• Make sure the printer power is turned off before cleaning.

• Wait for two to three minutes after power-off before head cleaning because the head part may become very hot during printer operation.

• Take care not to touch the heating region of the head with your hand while cleaning the head part.
  → The printer head may be damaged by static electricity.

• Take care to avoid scratching the head.

• Clean the printer head periodically if linerless paper is used. Recommended cleaning period is after consuming ten rolls of linerless paper (100 meters), or more than once a week. Printing quality may be degraded or printer life may be shortened if the head is not cleaned periodically.

Warning

Use only the linerless paper that is provided by BIXOLON. Use of other paper voids product warranty.

 Appendix

Specifications

Printing

| Printing Method| Thermal printing
Printing Speed| 100 mm/sec (Receipt Paper), 80 mm/sec (Linerless Paper)
Resolution| 203 DPI
Paper Supply Mode| Easy paper loading
Character Size| Font A: 12 × 24     Font B: 9 × 17     Font C: 9 × 24
Characters Per Line| Font A: 32            Font B/C: 42
Character Set| English: 95

Expanded Graphics: 128 × 33 pages

International: 32

Barcode

| 1   Dimension: UPC A, UPC E, CODE 39, CODE 93, Code 128,

EAN 8, EAN 13, ITF, Codabar

2  Dimension: PDF417, DATAMATRIX, MAXI, QR Code,

GS1 DataBar, Aztec

Emulation| BXL/POS
Windows Driver OPOS/JPOS Driver| Windows XP SP3(32bit) / SP1(64bit) / 2003 Server(32/64bit) / VISTA(32/64bit) / 2008 Server(32/64bit) / 7(32/64bit) /

8(32/64bit) / 10(32/64bit)

Linux Driver| Kernel 2.6.32 and later
Windows SDK| Windows XP / 2003 Server / VISTA / 2008 Server / 7 / 8 / 10 / CE 5.0 and later
Android SDK| Android 4.0 and later
iOS SDK| iOS 8.0 and later
Utility| Unified Mobile Utility, Net Configuration Tool, Android Utility, iOS Utility
Sensor| Paper End Sensor, Paper Cover Open Sensor, Black Mark Sensor (Option)
Cutter Type| Tear-Bar
Language| User language supported

Paper

| Paper Shape| Receipt| Linerless
Paper Type| Thermal Paper| Thermal Paper
Outer Diameter of Paper Roll| Max. ø40 mm (1.57”)| Max. ø39 mm (1.54”)
Width| 57.5 ± 0.5 mm (2.26” ± 0.2”)| 57.5 ± 0.5 mm (2.26” ± 0.2”)
Thickness| 0.07 ± 0.003 mm| 0.08 ± 0.008mm
Reliability| Printer| 50 km (Receipt Paper), 10 km (Linerless Paper)
Battery| Rechargeable up to 500 times

Communications

| ****

Interface

| USB, Bluetooth V4.1(Classic / LE), NFC Auto paring Wireless LAN 802.11 a/b/g/n

• Wireless communication is enabled only for devices with Bluetooth or Wireless LAN function.

Battery Charger

| Input| Voltage: 100 ~ 250 VAC  Current: 0.5A (Max. at 110VA)
Output| Voltage: 8.4 VDC  Current: 0.8A

• Charging current and charging time may depend on the type (option) of the charger.

Battery

| Type| Lithium-ion
Output| Voltage: 7.4 VDC (Available 8.4 ~ 6.8VDC) Capacity: 1200 mAh
Charging Time| 2.5 hours

Usage Conditions

| ****

Temperature

| Printer: -15~50℃ (5~122℉) Battery: 0~40℃ (32~104℉)

Battery discharge: -20~60℃ (-4~140℉)

Humidity| Printer: 10~80% RH (No condensation)

Battery: 20~70% RH(Non-condensing, refer to the tempera ture conditions on page 8)

Dimensions| Printer| 79.6mm × 114.2mm × 44.3mm (3.13″ × 4.5″ × 1.74″)

Weight

| ****

Printer

| Printer: 160g (0.35lbs)

Printer + Battery: 215g (0.47lbs)

Printer + Battery + Paper : 250g (0.55lbs) Package: approx. 720g (1.59lbs)

Accessories| Basic Package| Battery Pack, Battery Charger, Belt Clip, Paper, Power Cord, CD, Manual Quick
| ****

Sold Separately

| Belt Strap, Vehicle Charger, Interface Cable, Single Battery Cradle, Shoulder Strap, Case, Cleaning Pen, Battery Pack_V2 (with outer contacts), Single Docking Cradle, Quad Docking

Cradle, Quad Battery Charger, Wall Mount(for Quad Battery Charger)

---|---|---

Certification

WEEE (Waste Electrical and Electric Equipment)

This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office for details of where and how they can conduct environmentally safe recycling of such items. Commercial users should contact their suppliers and check the terms and conditions of purchase contracts. This product should not be combined with other commercial waste for disposal.

Rating Label Symbol Information

DC (Direct current)

1. This equipment is indoor use and all the communication hiring is limited to inside of the building.
2. The switch is the disconnecting device. Turn off the switch from any hazard.

Warning
Lithium-ion Battery pack The battery has the potential risk of overheating, fire and/or explosion. To avoid such risks, observe the following instructions:

• A visibly swollen battery may be dangerous. Contact BIXOLON or your local dealer.
• Only use an eligible charger.
• Keep away from open flames. (Do not place in a microwave.)
• Do not leave the battery pack inside a vehicle in the summertime.
• Do not store or use in a hot and humid place like a sauna with sleeping rooms.
• Do not place the battery pack on a quilt, an electric blanket or a carpet for a long time.
• Do not store the battery pack switched on in an enclosed place for a long time.
• Do not allow the battery port to touch metal items, such as necklaces, coins, keys or clocks etc.
• Use the lithium secondary cell guaranteed by the mobile phone manufacturer or BIXOLON.
• Do not disassemble, compress or pierce the battery pack.
• Do not drop the battery pack from a high place or subject it to strong shock.
• Do not expose the battery to high temperatures over 60oC.
• Do not be exposed to humidity.

Disposal Directions

• Do not dispose of used battery packs carelessly.
• Do not burn or throw in a fire to dispose of the battery pack. There is a risk of fire and/or explosion.
• Dispose of battery packs according to the methods defined by your country or region.

Recommendation for Charging

• Charge your battery pack according to the instruction manual to avoid risks of fire or explosion.

FCC STATEMENT

FCC compliance Information

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to the user
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING : Exposure to Radio Frequency radiation. To conform to FCC RF exposure requirements this device shall be used in accordance with the operating conditions and instructions listed in this manual. Note that there are several radio options available with this printer. Additional regulatory information is contained in later sections devoted to each radio individually.

Label Types
The labels used on this product are composed of the following materials;

• BIXOLON logo label: PC
• Rating Label: PP
• Other labels: PET

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>