DENVER LED-3279 32 Inch HD Ready LED TV User Manual

DENVER LED-3279 32 Inch HD Ready LED TV

Model: LED-3279
To obtain the best performance and safety, please read this manual carefully. Please keep this manual for future reference.

SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS – PLEASE READ CAREFULLY BEFORE USE. The following safety instructions are located on the back of the TV.

• DANGER OF ELECTRIC SHOCK! NEVER REMOVE THE SCREWS OF THE COVER. NO USER-SERVICEABLE PARTS IN THE DEVICE. REPAIR ONLY BY QUALIFIED SERVICE PERSONNEL.
• The exclamation mark in the equilateral triangle indicates important operating and maintenance instructions
• The flash in the equilateral triangle indicates high voltage in the device, which can lead to electric shock

Please follow the instructions below:

• Do not use this TV near water.
• Only clean the device with a damp cloth.
• Do not block any ventilation openings.
• Set up the television in accordance with the supplied quick guide and these operating instructions.
• Lay the power cable so that it cannot be stepped on or pinched. Pay special attention to the plug and the point at which the cable is led out of the television.
• Do not let the power cord hang over the edge of the table.
• Disconnect the TV from the mains if there is a thunderstorm or if it is not used for a long period

WARNING! EXPOSE THE TELEVISION TO AVOID FIRE OR ELECTRIC SHOCK OR RAIN OR MOISTURE. THE TELEVISION SHOULD NEVER BE EXPOSED TO SPLASH / DRIP WATER AND NO OBJECTS FILLED WITH LIQUID ON THE TELEVISION

NOTE: Open flames (such as candles) should never be placed on the TV
Smells from the TV

• New TVs can cause unusual smells when they are switched on for the first time.
• Due to the manufacturing process of the components, the television and other electronic products may have parts that produce odors when they are first turned on and warmed up.
• The smell usually disappears after a few days of use and does not return.
• This is normal and occurs with many electronic devices. Ensure that there is sufficient ventilation in and around the device so that the smell can disappear.

EXTERNAL SCHEMATIC AND INSTALLATION

• SCART: AV input from a device like VCR
• Coax Out: Digital Audio Output from TV
• DVB-S : Connect RF signal from satellite/DVB-S
• DVB-T: Connect Analog/ATV signal or Digital/ DVB-T or DVB-C signal
• HDMI1/HDMI2: Connect HDMI input signal from signal source such as DVD USB: USB support multimedia  playback and software upgrade
• CI Slot: Insert CI card for Digital TV
• Mini AV In : Mini AV input from video playback device
• Mini YPbPr In: Mini component input from a video playback device
• Earphone Out : Audio output from TV through Earphone

EXTERNAL SCHEMATIC AND INSTALLATION

Antenna/Cable Connection

• a. Connect the Plug of the antenna cable or CATV cable to the cable (not provided with this unit), then connect to the antenna input of this unit for best reception.
• b. If the antenna cable in your home is other than the above two or you have problems in installing the antenna, please contact your dealer.

Notes:

• a. Current outdoor antenna or cable TV use 75 OHM coaxial antenna cable. For better reception suggest this kind of antenna cable
• b. Flat cable or indoor antenna are old designed, the reception may not be good enough

REMOTE CONTROLLER

REMOTE CONTROLLER

SOURCE

• Press INPUT button to display the input source list Press ▼ / ▲ or OK button to select the input source you want
• Press OK button to enter the input source Press EXIT button to quit

BASIC OPERATION

First Time Installation

• Connect an RF cable from the TV’s input called “RF-In” and to your TV Aerial socket. Select Language
• Press ◄ / ► button to select the language to be used for menus and message. Select Country
• Press ▼ / ▲ button to highlight country menu.
• Press ◄ / ► button to select the country you want to

BASIC OPERATION

Auto Tuning
First tuning ATV, press Menu and left arrow button to skip ATV tuning, Second tuning DTV, press Menu and left arrow button to skip DT

Setup

• Press MENU button to display the main menu.
• Press ◄ / ► button to select SETUP in the main menu.
• Press ▼ / ▲ button to select the option that you want to adjust in the SETUP menu. Press Enter button to adjust.
• After finishing your adjustment, Press Enter button to save and return to the previous menu.

Language

• Select an OSD menu language can be displayed. Default English is selected as menu language. Press ▼ / ▲ / ◄ / ► button to select Menu Language.

Audio Languages

• Press ▼ / ▲ button to select Audio Languages, then press Enter button to enter sub-menu.
• Press ◄ / ► button to select the primary of Audio Languages.
• Press ▼ / ▲ / ◄ / ► button to select the Audio Languages.

Subtitle Language

• Press ▼ / ▲ button to select Subtitle Language, then press Enter button to enter sub-menu.
• Press ◄ / ► button to select the primary of Subtitle Language.
• Press ▼ / ▲ / ◄ / ► button to select the Subtitle Language.
• Hearing Impaired
• Press ▼ / ▲ button to select Hearing Impaired, then press Enter button to select On or Off.

PVR File System

• Press ▼ / ▲ button to select PVR File System, then press Enter button to enter sub-menu.
• Press ▼ / ▲ button to select Check PVR File System,
• Then press Enter button to enter, it will check the USB speed.
• Aspect Ratio
  Press ▼ / ▲ button to select Aspect Ratio, then press Enter button to enter sub-menu. Press ▼ / ▲ button to select aspect ratio. (Available options are: Auto, 4:3, 16:9, Zoom1, Zoom2)

Blue Screen

• Press ▼ / ▲ button to select Blue Screen, then press Enter button to select On or Off. First Time Installation
• Press ▼ / ▲ button to select First time installation, then press Enter button to enter. Reset
• Press ▼ / ▲ button to select Reset, then press Enter button to enter sub-menu. Software Update (USB)
• Press ▼ / ▲ button to select Software Update (USB), plug your USB device in the USB slot, then press Enter button to update the right software.

HDMI CEC

• Press ▼ / ▲ button to select HDMI CEC, then press Enter button to enter the sub-menu.
• HDMI CEC Press ◄ / ► button to turn the HDMI CEC On or Off.
• HDMI ARC Press ◄ / ► button to turn the HDMI ARC On or Off.
• Auto Standby Press ◄ / ► button to turn the Auto Standby On or Off.
• Device List Press Enter button to open the main menu of device.

Picture

• Press MENU button to display the main menu.
• Press ◄ / ► button to select PICTURE in the main menu
• Press ▼ / ▲ button to select the option that you want to adjust in the PICTURE menu. Press OK button to adjust.
• After finishing your adjustment, Press MENU button to save and return back to the previous menu

Picture Mode

• Press ▼ / ▲ button to select Picture Mode, then press OK button to enter sub-menu. You can change the value of contrast, brightness, color, sharpness and tint when the picture is in Personal mode.
• TIPS: You can press PMODE button to change the Picture Mode directly
• Contrast/ Brightness/ Color/ Tint / Sharpness
• Press ▼ / ▲ button to select option, then press ◄ / ► button to adjust.
• Contrast Adjust the highlight intensity of the picture, but the shadow of the picture is invariable.
• Brightness Adjust the optical fiber output of the entire picture, it will affect dark region of the picture.
• Color Adjust the saturation of the picture based on your own liking
• Tint Use in compensating color changed with the transmission in the NTSC code. Sharpness Adjust the peaking in the detail of the picture

Color Temp

• Change overall color cast of the picture
• Press ▼ / ▲ button to select Color Temperature, then press OK button to enter sub-menu. Press ▼ / ▲ button to select Color Temperature. (Available Picture mode: Cold, Normal, Warm).
• Change the value of red, green and blue when the color temperature is in User mode
• Cold Increase the blue tone for the white.
• Normal Set to default color temperature.
• Warm Increase the red color for the white

Noise Reduction

• Filter out and reduces the image noise to improve picture quality.
• Press ▼ / ▲ button to select Noise Reduction , then press OK button to enter sub-menu.
• Off Select to turn off video noise detection.
• Low Detect and reduce low video noise.
• Middle Detect and reduce moderate video noise. High Detect and reduce enhanced video noise. Default Set as Default.

Sound

• Press MENU button to display the main menu.
• Press ◄ / ► button to select SOUND in the main menu
• Press ▼ / ▲ button to select the option that you want to adjust in the SOUND menu.2. Press Enter button to adjust.
• After finishing your adjustment, Press Enter button to save and return to the previous menu

Sound Mode

• Press ▼ / ▲ button to select Sound Mode, then press Enter button to enter sub-menu. Press ▼/▲ button to select.

• You can change the value of Treble and Bass when the sound is in Personal mode.
  TIPS: You can press SMODE button on the remote control to change the Sound Mode directly.

• Standard Produces a balanced sound in all environments.

• Music Preserves the original sound. Good for musical programs.

• Movie Enhances treble and bass for a rich sound experience.

• Sports Enhances vocals for sports.

• Personal Select to customize sound settings

• Note: The treble and bass are only available in Personal mode, you can adjust them as you like.

Balance

• Press ▼ / ▲ button to select option, Press ◄ / ► button to adjust.

Auto Volume level

• Press ▼ / ▲ button to select Auto Volume Level, then press ◄ / ► button to select On or Off. SPDIF Mode
• Press ▼ / ▲ button to select SPDIF Mode, then press ◄ / ► button to select Off / PCM / Auto

AD Switch

• Press ▼ / ▲ button to select AD Switch, then press ◄ / ► button to select On or Off. Amblyopia function for the blind, the tracks will be mixed describe the current screen .
• It needs code stream to support.

Note:

• Balance: This item can adjust the speaker’s output, it enables you to listen to best at your position.
• Auto Volume: This item is used for reducing the difference between channel and program’s volume automatically.

Channel

• Press MENU button to display the main menu.
• Press ◄ / ► button to select CHANNEL in the main menu

1. Press ▼ / ▲ button to select the option that you want to adjust in the CHANNEL menu.
2.  Press Enter button to adjust.
3. After finishing your adjustment, Press Enter button to save and return to the previous menu

Auto Tuning
Press ▼ / ▲ button to select Auto Tuning, then press Enter/► button to enter

ATV Manual Tuning

• Current CH>
• Set the channel number.
• Color System>
• Select the color system
• Sound System>
• Select the Sound system
• Fine-Tune>
• Adjust the frequency of the channel finely.
• ( Available System: AUTO, PAL , SECAM ) Search>
• Start searching channel

DTV

• Press ▼ / ▲ button to select Manual Tuning, then press Enter button to enter sub-menu. Press ◄ / ► button to select channel, then press Enter button to search program. Manual
• Tuning

Program Edit

• Press ▼ / ▲ button to select Program Edit, then press Enter button to enter sub-menu
• The three colored key is the shortcut key for programming the channel
• First press ▼ / ▲ to highlight the channel you want to select, then:
• Press the Red button to delete the program in the list.
• Press the Yellow button to move the channel in favorite list.
• Press the Blue button to skip the selected channel.
• Press Fav button to add or remote the channel to your favorite list.
• (Your TV set will skip the channel automatically when using
• CH+/- to view the channels.)

Schedule List

• Press ▼ / ▲ button to select Schedule List, then press Enter button to enter sub-menu. It is available in source
• Press the YELLOW button to enter the interface below:
• When the time appointment is conflict, it will produce a warning message:
• The CHANNEL List in Satellite Source
• Auto Tuning
  Press ▼ / ▲ button to select Auto Tuning, then press Enter/► button to enter

Dish Setup

• Press ▼ / ▲ button to select Dish Setup, and then press Enter/► button to enter.
• Press MENU button to call out the main menu.
• Highlight “Channel” using navigation buttons and press OK to enter it.
• Then highlight “Dish Setup” and press OK to enter it.
• Press LEFT/RIGHT navigation button to highlight Left, Middle or Right column.
• Press EXIT button to return.

A. When the “Satellite” column is highlighted:

1. Press YELLOW button to enter Add menu.
   Satellite Name
   Press RIGHT navigation button to enter rename page.
   Use navigation buttons to complete a new name.
   Longitude Direction
   Press LEFT/RIGHT navigation button to select desired option. Longitude Angle
   Press LEFT/RIGHT navigation button to move the cursor and press number buttons on remote control to input desired value. Band
   Press LEFT/RIGHT navigation button to select desired option

2. Press GREEN button on remote control to enter Edit menu. The operations of Edit menu are the same as Add menu.

3. Press BLUE button on remote control to enter Scan menu. Press UP/DOWN navigation button to highlighted desired item. Press RIGHT navigation button to select desired Scan Mode, Channel Type and Service Type.

4. Press RED button to delete
   Press EPG button to switch satellite and Transponder.

B. When the “Transponder” (Middle) column is highlighted:(1)Press YELLOW button on remote control to enter Add menu. Frequency
Press LEFT/RIGHT navigation button to move the cursor and press number buttons on remote control to input desired value. Symbol (ks/s)
Press LEFT/RIGHT navigation button to move the cursor and press number buttons on remote control to input desired value. Polarity
Press LEFT/RIGHT navigation button to select desired option

1. Press GREEN button on remote control to enter Edit menu The operations of Edit menu are the same with Add menu.
2. Press BLUE button on remote control to enter Scan menu. Press UP/DOWN navigation button to highlighted desired item. Press LEFT/RIGHT navigation button to select desired Scan Mode, Channel Type and Service Type

C. When the “Ku_ASTRA…” (Right) column is highlighted:

• LNB (Low Noise Block) Type
  • Press LEFT/RIGHT navigation button to enter submenu. Then use UP/DOWN navigation button to select desired option.
• LNB Power
  • Press LEFT/RIGHT navigation button to select desired option.
• 22 kHz
  • Press LEFT/RIGHT navigation button to select desired option.
• Toneburst
  • Press LEFTRIGHT navigation button to select desired option.
  • DisEqc1.0 (Digital Satellite Equipment Control)
  • Press LEFT/RIGHT navigation button to select desired option.
• DisEqc1.1
  • Press LEFT/RIGHT navigation button to select desired option.
• Motor
  • Press LEFT/RIGHT navigation button to select desired option
• EPG
  • Press EPG in the remote control to record the programs.
  • Press UP/DOWN navigation button to select preferred program.
  • Press LEFT/RIGHT navigation button to switch between left column and right column. When a program is highlighted (cursor moved to Right column):
  • Press RED button to record program.
  • Press GREEN button repeatedly to set a reminder.
  • Press YELLOW button to display program guide of previous day.
  • Press BLUE button to display program guide of next day.

Time
Press MENU button to display the main menu. Press ◄ / ► button to select TIME in the main menu.

• Press ▼ / ▲ button to select the option that you want to adjust in the TIME menu.2. Press Enter button l to adjust.
• After finishing your adjustment, Press Enter button to save and return to the previous menu Off Time Press ◄ / ► button to select On/Off
• On Time Press ◄ / ► button to select On/Off
• Time Zone Press ▼ / ▲ button to select Time Zone, then press Enter button to enter sub-menu.
• Press ▼ / ▲ / ◄ / ► button to select time zone

Sleep Timer

• Press ▼ / ▲ button to select Sleep Timer, then press Enter button to enter sub-menu.
• Press ▼ / ▲ button to select. (Available options are: Off,10min,20min,30min,60min,90min, 120min,180min,240min).
• Press ▼ / ▲ button to select Auto Standby, then press ENTER button to enter sub-menu
• Press ▼ / ▲ button to select
• Tips : The remote control does not make any operation in the hypothesis time, it will close down automatically. If you do any operation, it will reset time.

OSD Timer

• Press ▼ / ▲ button to select OSD Timer, then press ENTER button to enter sub-menu
• Press ▼ / ▲ button to select

Lock

• Press MENU button to display the main menu.
• Press ◄ / ► button to select Lock in the main menu
• Press ▼ / ▲ button to select the option that you want to adjust in the LOCK menu.
• Press Enter/◄ / ► button to adjust.
• After finishing your adjustment, Press MENU button to return back to the previous menu
• System Lock
  • Press ▼ / ▲ button to select System Lock, Then press ENTER button to make following four options valid.
  • Default Password is 0000, if you forget what you set, please call service center.
• Set Password
  • Press ▼ / ▲ button to select Set Password, then press Enter button to enter sub-menu to set new password.

Channel Lock

Press ▼ / ▲ button to select Channel Lock then press Enter button to enter sub-menu to select. Press GREEN button to lock or unlock the channel.

Parental Guidance

• Press ▼ / ▲ button to select Parental Guidance, then press Enter button to enter sub-menu to select the number of age which is suitable for your children.
• Key Lock
  Press ▼ / ▲ button to select Key Lock, then press ◄ / ► button to select Off or On. When Key Lock’s statue is on, you can’t use the Key panel button.

Hotel

• Press ▼ / ▲ button on the remote control to select hotel mode in the Lock menu.
• Press Enter button on the remote control to enter the sub-menu.
• After finishing your adjustment, Press MENU button to save and return back to the previous menu.
• Hotel Mode
  • Press ▼ / ▲ button to select Hotel Mode, then press ◄ / ► button to select on or off. Source Lock
  • Press ▼ / ▲ button to select Source Lock to lock the source you want, then press Enter button to enter sub-menu to select.
• Default Source
  • Press ▼ / ▲ button to select Default Source, then press ENTER button to enter sub-menu to select.
• Default Prog
  • Press ▼ / ▲ button to select Default Prog, then press ◄ / ► button to adjust.
  • It is available when the default source is TV.
• Max Volume
  • Press ▼ / ▲ button to select Max Volume, then press ◄ / ► button to adjust.
• Clear Lock
  • Press ▼ / ▲ button to select Clear Lock, then press Enter button to clear the setting you have done before

MULTIMEDIA OPERATION

• Media

  • Note: Before operating Media menu, Plug in USB device, then press INPUT button to set the Input Source to Media .
  • Press ▼ / ▲ button to select Media in the Source menu, then press Enter button to enter. Press ◄ / ► button to select the option you want to adjust in the main Media menu,  then press Enter button to enter.

• Movie

  • Press ◄ / ► button to select MOVIE in the main menu, then press Enter button to enter. Press Exit button to return to the previous menu and exit menu to quit. Press ◄ / ►  button to select drive disk you want to watch, then press Enter button to enter.
  • Press media button to play the selected movie.
  • Press display button to select menu in the bottom you want to run, then press Enter button to operate.
  • Press Exit button to back to the previous menu and exit button to quit the entire menu

• Music
  Press ◄ / ► button to select MUSIC in the main menu, then press Enter button to enter. Press Exit button to return to the previous menu and exit menu to quit.

• Press ◄ / ► button to select drive disk you want to watch, then press Enter button to enter.

• Press ◄ / ► button to select return option to the previous menu.

• Photo
  Press ◄ / ► button to select PHOTO in the main menu, then press Enter button to enter.

• Press Exit button to return to the previous menu and exit menu to quit.

• Press ◄ / ► button to select the file you want to watch in the file selecting menu, then press media button to display picture.

• When highlighting the option you select, the file information will appear on the right and picture will be previewed in the center.

Text

• Press ◄ / ► button to select TEXT in the main menu, then press Enter button to enter. Press Exit button to return to the previous menu and exit menu to quit.
• Press ◄ / ► button to select drive disk you want to watch, then press Enter button to enter.
• Press ◄ / ► button to select return option to back to the previous menu.

ENERGY LABEL

Please notice – All products are subject to change without any notice. We take reservations for errors and omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S

• Electric and electronic equipment and included batteries contains materials, components and substances that can be hazardous to your health and the environment, if the waste material (discarded electric and electronic equipment and batteries) is not handled correctly.
• Electric and electronic equipment and batteries is marked with the crossed out trash can symbol, seen above. This symbol signifies that electric and electronic equipment and batteries should not be disposed of with other household waste, but should be disposed of separately.
• As the end user it is important that you submit your used batteries to the appropriate and designated facility. In this manner you make sure that the batteries are recycled in accordance with legislature and will not harm the environment.
• All cities have established collection points, where electric and electronic equipment and batteries can either be submitted free of charge at recycling stations and other collection sites, or be collected from the households. Additional information is available at the technical department of your city.
• Hereby, Inter Sales A/S declares that the radio equipment type LED-3279 is in compliance with Directive 2014/53/EU.
• The full text of the EU declaration of conformity is available at the following internet address : www.denver-electronics.com and then click the search ICON on topline of website.
• Write model number: LED-3279. Now enter product page, and red directive is found under downloads/other downloads.
  • http://www.denver-electronics.com/denver-cau-438/Operating
  • Frequency Range : VHF
  • (50MHz ~ 230 MHz), UHF (474MHz ~ 862 MHz) Max Output Power: 45W
  • DENVER ELECTRONICS A/S
  • Omega 5A, Soeften, DK-8382 Hinnerup, Denmark www.facebook.com/denverelectronics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>