Donut 2BD8W-I5 All in One Turntable System User Manual
- June 17, 2024
- Donut
Table of Contents
guidebook
Donut for close friends
2BD8W-I5 All in One Turntable System
User Manual
SAFETY INSTRUCTIONS
-
Read this manual.
-
Keep this manual.
-
Note all warnings.
-
Comply with all notices.
-
Do not use this product near water.
-
Clean the product only with a dry cloth.
-
Do not block any vents, and install according to the manufacturer’s instructions.
-
Do not install near any heat sources, such as radiators, hot air regulators, stoves or other instruments that generate heat.
-
Protect the power cord from being stepped on or pinched, especially plugs, sockets, and product power outlets.
-
Only use accessories specified by the manufacturer.
-
All maintenance work should be carried out by qualified maintenance personnel.
When the product is damaged due to the following conditions, maintenance should be carried out: when liquid is splashed into the product or foreign objects fall into the product, the product is exposed to rain or moisture, does not work properly, or falls to the ground. -
In case of thunderstorm weather or long-term non-use, please unplug the product.
-
Unplug the power cord from the AC power socket to completely disconnect the AC power of product.
-
Do not place open flame sources, such as lighted candles, on this product.
Warning
It is strictly forbidden to expose this product to rain and humidity to
reduce the risk of fire and electric shock. This product should be protected
from exposure to water.
It is strictly forbidden to put liquid containers on this product, such aswine
bottles, vases, etc.
Attention
Product has been tested for level adjustment before leaving factory it is
recommended to be placed on a horizontal table for use.
Only applicable to areas below 2000 meters.
Only suitable for non-tro-pical climatic conditions.
Product List
Unboxing method
- The package contains small spare parts.
To avoid omissions, please check the product list carefully.
Parts name
- Turntable
- Remote control
- Power /Volume button
- Belt
- Platter
- Anti-Slip mat
- Spindle
- Stylus protective cover
- Tonearm
- Tonearm buckle
- Tonearm lifter
- Control knob
- Counterweight
14. Pulley
15. Bugle
16. Bugle base
17. Bugle support rod
18. Bugle mount seat| 19. Power cable
20. Power interface
21. Power switch
22. Audio IN
23. 3A insurance
---|---
Assembly
Place the package in the direction indicated by ↑, remove the protective film of package, remove the top cover of the carton, tear off the Velcro from the side of the package, take out the product accessories from top to bottom, and install it according to the following steps:
Step 1
Remove the transport screws on the platform of the turntable.
Step 2
Insert the bugle support rod into the bugle mount seat, fasten it with the
plug cable of the bugle base. After the cable being fastened, push the bugle
Support rod all the way to the bottom before tightening up.
Step 3
Tighten the bugle along the screw thread in the bugle support rod.
Step 4
Insert the bugle support rod into the bugle mount seat with the front of
the bugle facing forward.
Step 5
Install the belt on the inner ring of platter along the same direction.
Step 6
Insert the spindle into the turntable shaft sleeve hole, place the platter
with the belt installed on the spindle.
Step 7
Pull the belt out from the hole of platter and install it on the pulley.
Step 8
Lay the anti-slip mat flat on the platter.
Step 9
Connect the power cable to the power interface on the rear panel of
turntable and the power socket.
Instructions
-
Connect the power cable to the power interface on the rear panel of turntable and the power socket.
-
Long press power/volume button for 3 seconds, will hear the power-on prompt tone (turntable has 3 modes, press power/volume button to switch mode: a. Vinyl Mode; b. Blue tooth Reception; c. Audio Input).
-
After powering on, press power/volume button once to enter Vinyl Mode, will hear the prompt tone Vinyl Mode.
The steps of vinyl playback are as follows:
a. Lay the record flat on the platter.
b. Move the tonearm above the record.
c. Switch the speed switch knob to the required speed (33/45).
d. Put the tonearm lifter down, stylus touches the record slowly, music playing.
e. Rotate the power/volume button to adjust the volume. -
The steps to stop vinyl playback are as follows:
a. Raise tonearm lifter, stylus leaves record.
b. Move the tonearm to the cradle.
c. Switch the speed switch knob to 0 position.
d. Place the record in the record sleeve. -
After powering on, press power/volume button twice to enter Bluetooth Reception mode, will hear the prompt tone Bluetooth Reception.
The steps of Bluetooth Reception are as follows:
a. Search for the Bluetooth name “i5” on Bluetooth device.
b. Click “i5” to connect (will hear the prompt tone after the successful connection).
c. Choose music on Bluetooth device, turntable will play music. -
After powering on, press power/volume button 3 times to enter Audio Input mode, will hear the prompt tone Audio Input.
The steps of Audio Input are as follows:
a. Connect audio cable to the AUDIO IN interface on the rear panel of turntable.
b. The external playback device plays music, turntable will play music synchronously. -
Power off (long press power/volume button for 3 seconds, will hear the power-off prompt tone).
Remote controller
01 Mute
02 Power
03 Play / Pause
04 Volume +
05 Last track
06 Next track| 07 Volume –
08 Treble-
09 Treble+
10 Mode
11 Bass-
12 Basst+
---|---
Parameters
| Input voltage | AC 220V/50Hz |
|---|---|
| Tonearm Parameter | Mounting Distance 200mm |
Effective Length 218mm
Overhang 18mm
Offset Angle 26°
Tracking force 2.5-3.5g
Phono pre-amplifier| Built in HiFi MM phono amplifier
Speaker Parameter| 1″ treble speaker (8Ω 10W)
6.5″ inch midrange speaker (4Ω 40W)
8″ woofer (4Ω 60W)
SNR| Bluetooth ≥ 65dB
vinyl ≥ 90dB
Output powe| 110W (max)
Unit dimension| 4403971565mm
N.W.| 30KG
Package dimension| 6155051155mm
G.W.| 37.5KG
i5
FENNESST. x Jasmine’ Co-productionhttp://www.fennessy.hk/
Scan code for more information
Copyright@Fennessy
Subject to change without notice
www.fennessy.hk
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any inte rference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interferenceto radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.