Warm Living WL-1500R-T3 Electric Fireplace Stove Heater Owner’s Manual

Electric Fireplace Stove with Heater

OWNER’S MANUAL

Model No. WL-1500R-T3

PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.

Thank you for choosing Warm Living Electric Stove. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.

IMPORTANT INSTRUCTIONS

When using this electric unit, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read ALL instructions before using this unit.
2. CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
3. This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater.
4. Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and curtains at least 3 ft from the front of the heater and keep them away from the sides, top, and rear. DO NOT place towels or other objects on the heater.
5. Extreme caution is necessary when any heater is used by or near children or the disabled, or when the heater is left operating and unattended.
6. DO NOT operate any heater with a damaged cord or after the heater malfunctions, has been dropped or damaged in any manner. Return heater to authorized service facility for examination, electrical or mechanical adjustment, or repair.
7. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER locate heater where it may fall into a bathtub or other water container. To protect against electrical hazards, DO NOT immerse in water or other liquids.
8. DO NOT touch the control panel or plug with a wet hand.
9. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
10. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
11. To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.
12. A heater has hot components or sparking parts inside. DO NOT use in areas where gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away from heated surfaces and open flames.
13. Always plug heaters directly into a wall outlet receptacle. Never use with an extension cord or relocatable power tap (outlet/power strip).
14. To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
15. To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly on the plug, DO NOT unplug by pulling on the cord.
16. Always unplug the unit before moving or cleaning, or whenever the heater is not in use.
17. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments is not recommended.
18. Always use on a dry, level surface. Use on floor only.
19. DO NOT use outdoors.
20. WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any solid-state speed control device.
21. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. Qualified personnel should perform all servicing only.

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

SAFETY FEATURES

Overheat Safety Feature
This heater is equipped with a overheat safety feature. When the heaters internal components reach a certain temperature that could cause overheat and possible fire, the heater will automatically shut off.

IN THE BOX
REMOTE CONTROL (2 AAA Batteries Not Included)
ELECTRIC STOVE LEG(4pcs) SCREW(12pcs) *INSTRUCTION BOOKLET

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents above. If any part is missing or damaged, do not attempt to assemble the product. Contact customer service for replacement parts.

Tools Required for Assembly (not included): Phillips screwdriver

ASSEMBLY INSTRUCTIONS

Lay stove upside down on a padded surface with the underside accessible. Attach leg to stove by inserting the tab on the top of the leg into the corresponding slot on the bottom of the stove. Insert three screws into predrilled holes and tighten securely. Repeat with remaining three legs

PRODUCT DIAGRAM

1. Display window

A Control panel

1. Power indication light: After light shows red, press the power button to display the red light and flame open.
2. Power button: Powers the display on and off.
3. Flame light
4. Flame light button: Adjusts the brightness of the flame
5. Timer light
6. Timer button: User setting timing on or shutdown
7. Up button: For setting temperature or time upward
8. Down button: For setting temperature or time downward
9. Heater button: Set up the heater mode and turn off the heat.
10. Low range mode lights: Low range mode indicator lights up for low-grade heat.
11. High range mode lights: High range mode indicator lights up for high-grade heat.

Digital display: Indicates set temperature or time value according to the timer or high and low heating mode display. After 5 seconds, the display window will blink, press any key to automatically display except for the power button

Remote Control

Power button: Powers the display on and off.
Up button: For setting temperature or time upward
Down button: For setting temperature or time downward
Flame light button: Adjust the brightness of the flame
Heater button: Set up the heater mode and turn off
Timer button: User setting timing on or shutdown

PREPARATION

Place the heater on a firm, level surface and plug into a 120V 60Hz power outlet. Turn on the power switch in the rear of the unit. Only operate heater in upright position. Insert 2 AAA batteries into the remote control before using (Batteries Not Included)

OPERATING YOUR HEATER

Once the Electric fireplace has been properly assembled and connected to a 120V 60Hz electrical outlet, and make sure the power switch is “ON”(main switch light is shining).it is ready to operate:

1.Start and select working mode

Power
or :

POWER

| Turn the heater on by pressing the ON/OFF button on the control panel or by pressing the Power button on the supplied remote control.

Once power is off, heating element will stop working at first. Fan will prolong working for 3 min to emit plenty of heat inside. This mark will indicate running during the 3 min.

---|---

Heater
Or

HEATER

| Select a heat setting.

Press the HEATER button to toggle between the two heat settings.

1. High
2. Low
3. Turn off

| Power for heat-up mode is 1500W; heat-down is 750W,and turn off the heat.

2. Setting room temperature

UP     DOWN
Or

UP    DOWN

| Adjust the thermostat by pressing the arrows on the control panel or remote control.
---|---
| Set temperature indication varies from 59°F to 86°F , or from 15°C to 30°C. Once you have chosen the desired temperature, the heater will remain on until the room temperature increases to the temperature on the digital display. The heater will cycle on and off to maintain the desired room temperature.

3. Setting flame

FLAME
Or

FLAME

| Adjust the brightness of the flame and turn off
---|---

4. Setting timer-power- off
Caution! ONLY under power-off mode can you set timer-power-off function.

TIMER
Or

UP DOWN
Or

UP DOWN| Adjust the time by pressing the arrows on the control panel or remote control.
| Digital display turns set temperature to time value for the timer. Press the UP and DOWN button more than once, the value will vary from 0 to 12hr (1 hr interval) in circulation.
Timer
| The light is on when timer -power-off is set.

5. Setting timer-power-on
Caution! ONLY under power-off mode can you set timer-power-on function.

TIMER
Or

UP DOWN
Or

UP DOWN| Adjust the time by pressing the arrows on the control panel or remote control.
| Digital display indicates time value for the timer. Press the UP and DOWN button more than once, the value will vary from 0 to 12hr (1 hr interval) in circulation.
Timer
| The light is on when timer -power-on is set.

6. Setting electro lock
Function of electro lock can avoid mis-operation from children. Locking can be set in both power-on and power-off modes.

UP
And

DOWN| Press Temp Up and Temp Down buttons once for 3 seconds. Locking is fulfilled when a buzzer rings. When locked, control panel and remote control failed to function.
---|---

UP
And
DOWN| When release is needed, please re-press Temp Up and Temp Down buttons once for 3 seconds. Release is fulfilled when a buzzer rings. Lock indication disappears. Control panel and remote control return to function.

MAINTENANCE

1. Glass Information

• Under no circumstances should this product be operated with missing or broken glass.
• Do not strike or slam the glass.
• Do not use abrasive cleaners to clean the glass.
• Replacement glass is available from the manufacturer and replacement should be carried out by a qualified service person.

2. Cleaning

• To clean the unit, first turn off controls on unit and unplug unit from power source.
• To clean the glass door: remove dust with clean dry cloth or to remove finger prints and other marks clean glass with clean damp cloth. Do not use abrasive cleaners or spray liquids on glass door surfaces.
• Metal and metal painted parts should be cleaned with clean damp cloth only. Do not use abrasive cleaners or spray liquids on this surface.

3. If you do not use the heater for a long time, please take out the remote batteries (to prevent corrosion) as shown below. Store the remote in a safe place.

1. lid
2. Battery

TROUBLE SHOOTING

If the heater will not operate, please check the following before seeking repair of service:

1. Check if the power cord is plugged into an electrical outlet, if not, plug in.
2. Check if electricity to the outlet is working.

Note: The heater may not be operating if the thermostat is set lower than the room temperature. To begin operation, increase the thermostat temperature for a higher heat setting.

STORAGE

Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up, use the original packaging to repack the unit.

For Customer Service Call
1-800-752-5262

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>