MATTER MADE 1CH Switch Module Instruction Manual
- June 17, 2024
- MATTER MADE
Table of Contents
INSTRUCTION MANUAL
Matter Switch Module
(1CH,2CH,3CH,4CH)
Mounting Clip
1. Reset Key
2. Indicator Light
Wiring Instructions and Diagrams
- Turn off the power supply before carrying out any electrical installation work.
- Connect wires according to the wiring diagram.
- Insert the module into the junction box.
- Turn on the power supply and follow switch module configuration instructions.
Without Switch
TECHNICAL SPECIFICATIONS
| Product type | Matter Switch Module |
|---|---|
| Voltage | AC100-240V 50/60Hz |
| Max. load | 1CH : 16A 2CH : 2x5A |
3CH : 3×3.3A 4CH : 4×2.5A
Operation frequency| 2.412GHz-2.484GHz
Operation temp.| -10℃ + 40℃
Protocol| Matter
Operation range| <100m
Dims (WxDxH)| 39.2×39.2×18 mm
IP rating| IP20
Warranty| 2years
Certificates| CE ROHS
with mounting clip
1CH Matter Switch Module
Single Control
Double Switch
INSTALLATION
Warnings:
- Installation must be carried out by a qualified electrician in accordance with local regulations.
- Keep the device out of reach of children.
- Keep the device away from water , damp or hot environment.
- Install the device away from strong signal sources such as microwave oven that may cause signal interruption resulted to abnormal operation of the device.
- Obstruction by concrete wall or metallic materials may reduce the effective operation range of the device and should be avoided.
- Do NOT attempt to disassemble, repair or modify the device.
2CH Matter Switch Module
Without Switch
Single Control
Double Switch
3CH Matter Switch Module
Without Switch
Single Control
4CH Matter Switch Module
Without Switch
Single Control
Double Switch
Home APP Instruction (1)
Pay attention:
(1) The mobile phone lOS system version must be 16.0 or later.
(2) A home hub (such as HomePod, HomePod mini, App ble TV, or iPad)must be set
up to add the Matter accessory to the home App;
(3) The Wi-Fi configured when pairing must be in the LAN with the hub.
Download App
(1) Open the APP Store, search the “Homekit” and download the APP.
(2) After the download,open the APP and log in using the local iCloud account.
Add device
Be default, the device is in standby mode (the pairing indicator flashes);
without the network status, please press the reset key for 5 seconds, and then
add the device.
The Device only supports 2.4GHz Wi-Fi signal, need to use the home hub to add.
Scan the device QR code to add (2)
Add via Serial number (3)
a, The APP automatically searches for the nearby devices, clicks the device
icon, and input the serial number to add
(4)
b. If no device is found, clicks “My Accessory Isn’t Shown Here”
Share device (5)
FAQ
Q1: What should I do if I can’t configure the switch module?
a. Please check whether device is powered on.
b. Make sure your mobile and switch module are under the same 2.4 Ghz WIFI
network.
c. Whether it’s in good internet conditions.
d. Make sure the password entered in App is correct.
e. Make sure the wiring is correct.
Q2: What device can be connected to this Wi-Fi switch module?
Most of your household electrical appliances can be, such as lamps, laundry machine, coffe maker, etc.
Q3: What happens if the WIFI goes off?
You can still control the device connected the switch module with your traditional switch and once WIFI is active again the device connected to module will connect automatically to your WIFI network.
Q4: What should I do if I change the WIFI network or change the password?
You have to re-connect our Wi-Fi switch module to the new Wi-Fi network accordingly as per the App User Manual.
Q5: How do I reset the device?
press the reset key for about 10 seconds until the indicator light inside the module is flashing quickly for pairing.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>