KEON JINN K1MIFZ014A LED Mirror User Manual
- June 11, 2024
- KEON JINN
Table of Contents
KEON JINN K1MIFZ014A LED Mirror
Product Information
Specifications
- Product: LED Mirror
- Voltage Range: 100V-240V
- Warranty: 1 year from date of purchase
- Anti-fog Feature: Yes
Product Usage Instructions
Installation Instructions
Before Installation
- Important Safety Instructions:
- Read all instructions carefully before assembly.
- Assemble with two or more adults.
- Qualified technician or electrician recommended for wiring.
- Disconnect power before installation.
- Ensure the fixing location can support the weight.
- Follow installation instructions to prevent injury.
- Pre-assembly:
- Inspect product for damage or missing parts upon receipt.
- Maintain voltage between 100V and 240V.
- Connect wires to junction box or plug.
- Do not remove silicone protector before installation completion.
Installation of LED Mirror
- Mounting Point Measurement:
- Mark holes for hanging board on wall.
- Use spirit level for straight alignment.
- Drill pilot holes and insert anchors.
- Screw the mounting plate.
- Connect the Power:
- Identify live (black), neutral (white), and ground (green) wires.
- Connect wires to lighting circuit or plug.
Frequently Asked Questions
- Q: What cleaning agents can be used on the mirror?
- A: It is recommended to use gentle liquid detergent or colorless cleanser to remove dirt. Avoid abrasive materials.
- Q: What should I do if the voltage exceeds 240V?
- A: In case the voltage exceeds 240V, use a transformer to regulate the voltage within the safe range.
- Q: How does the anti-fog feature work?
- A: The anti-fog pad converts electric energy into heat energy, warming the mirror surface to prevent condensation of water vapor.
BEFORE INSTALLATION
Thank you very much for using Keonjinn products, in order to facilitate the use of Keonjinn products, please read this instruction carefully before you begin installation.
Important Safety Instructions:
- Please read all instructions carefully before assembling the item.
- Assembly by two or more adults is highly recommended.
- To connect the wires to electrical junction box, a qualified technician or electrician is highly recommended.
- Disconnect power before installing, adding or changing any components.
- Ensure that the fixing location is able to take the weight of the complete fitting. (solid stone / brick walls).
- To prevent injury, the mirror must be installed according to these instructions.
Pre-assembly:
- After opening the package, inspect the product immediately upon receipt for transit damage or missing parts.
- Keep the voltages between 100V and 240V. If the voltage exceeds 240V, please use a transformer.
- You can connect the wires directly to your junction box or the plug.
- Do not remove the transparent silicone protector before completing the installation.
Before installation, please check to make sure the mirror is working properly :
After connecting the power, the two round buttons will turn white. At the moment the LED and anti-fog function are already turned on automatically. If you don’t need to use any one of them, just touch it to turn it off, then the button will be dimmed.
The above button is the anti-fog switch.
When you are not using it, remember to turn off the switch to prevent wasting
energy.
Anti-fog pad working principle: Anti-fog pad converts electric energy into
heat energy efficiently, and transmits heat directly to the mirror surface to
warm the mirror surface. The specific power is kept at a constant temperature,
which effectively prevents water vapor from condensing on the surface of the
mirror and acts as an anti-fog.
The below button is the smart switch.
This switch can control the light brightness and color temperature switching. Keep holding it and the brightness will change. You could adjust the color of light according to your preference: the first touch is white light, the second touch is yellow light, and the third touch is natural light. If no button is pressed within 15 seconds, pressing again will turn the light off immediately.
CONTACT US
Note: After opening the package, Please inspect the product immediately for damage in transit or missing parts. If there is any missing, Please contact us by (sales@keonjinn.com). or you can contact us at Amazon by following these steps:
- Open “Orders” at Amazon
- Find the product you have purchased and open the product page
- Click Sold by “Keonjinn” -Click”Ask a question”
- Click “An order I have placed”
- Click “Your product” -Click “Other” -Click “Troubleshooting”
Then you can send us messages,we will reply within 24 hours.
PACKING LIST
INSTALLATION TOOLS
INSTALLATION OF LED MIRROR
Mounting point measurement
Mark the holes for the hanging board on the wall.Then use a spirit level to make sure the hole is on a straight horizontal line.
Drill pilot holes on the marked spots
Insert the screw
Screw the mounting plate
Connect the power
There are three power wires behind the mirror, including the live wire (black), the neutral wire (white) and the ground wire (green). You can connect the wires to standard switched lighting circuit or plug.
If you want to connect power wires to the plug (For test power only), you can refer to the steps
- Remove the plug cover.
- Unscrew the screws on each of the plug’s pins.
- Insert the twisted copper wires into the holes in the pins.
- Tighten the little screw on each of the plug’s pins.
- Make sure the wire is tightly clamped by the brake or clip.
- Replace the cover of the plug.
Other power connection methods are on the same principle.
Mount the mirror on the wall and ensure it is sturdy
hang the mirror onto the board in wall.
PRODUCT SPECIFICATION
| Dimension | Watts | Lumens |
|---|---|---|
| Φ24 | 24W | 2130LM |
| Φ28 | 36W | 2570LM |
| Φ32 | 36W | 2943LM |
| Φ36 | 36W | 3551LM |
| Φ40 | 36W | 3820LM |
| PARAMETER | SPECIFICATION | |
| --- | --- | |
| Color Temperature | 3000-6000K | |
| Input Voltage | AC100-240V | |
| Output Voltage | 12V DC | |
| CRI | ≥90 Ra | |
| Working Temperature | -20~50℃ | |
| Life Span | ≥20000 hours | |
| Anti-fog | Yes | |
| Safety Compliance | ETL | |
| IP Rate | IP44 | |
| Mirror Glass | 5 mm | |
| Wiring Method | Hardwired / Plugin | |
| Switch | Touch Sensor Switch | |
| Mounting Method | Wall Mount |
USE AND CLEANING INSTRUCTION
In order to keep the LED mirror look perfectly, we suggest using and cleaning the mirror regularly.
- Please use in safe voltage range. (100V-240V).
- Use electrical tape to wrap around the wires to prevent leakage.
- Do not strike mirror glass with hard or pointed items.
Please obey the following procedure when you clean the mirror.
- It is recommended that the product is cleaned with a soft, nonabrasive cloth.
- Do not use Irritating cleaning agents or abrasive materials on any type of unfinished surface. Please use the any following cleanser to remove the dirt.
- Gentle liquid detergent.
- Colorless cleanser.
Product Warranty
Manufacturer warranty for 1 year from date of purchase.
If you have any problem, please feel free to contact us on
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>