MATTER MADE Discus Vine 6 Pendant Installation Guide

June 12, 2024
MATTER MADE

MATTER MADE logo Discus Vine 6 Pendant
**Installation Guide

**

Included for installation

1x Discus Vine 6

| | | |
---|---|---|---|---
1x Drop| 1x Canopy| 1x LED Driver| Slip ring, set screw, & hex key| 2x Nipple
| | | |
1x Crossbar| 1x Ground wire| 2x Crossbar screw| 1x Hex nut & lock washer| 5x Wire nut

Step 1.

  1. Caution : Turn off power at the circuit breaker before beginning installation. Matter Made recommends the Discus Vine 8 be installed by a qualified electrician.
    Carefully remove the Discus Vine 8 from the packaging and lay flat on a protected surface.
    Attach the threaded nipple (A) into the top of the fixture. Step 2

  2.  Feed the wires of the fixture through the drop (B) and attach the drop to the nipple at the top of the fixture.MATTER MADE Discus Vine 6 Pendant - Step 2 Step 3.

  3.  Slide the slip ring (C) over the drop and tighten the set screw using the hex key (D). Slide the canopy over the drop and rest it on the slip ring.MATTER MADE Discus Vine 6 Pendant - Step 3 Step 4.

  4. Attach the nipple (E) to the top of the drop.MATTER MADE Discus Vine 6 Pendant - Step 4 Step 5.

  5.  Attach the crossbar (F), lock washer (G), and hex nut (H) to the nipple on the top of the drop. Tighten the hex nut with a wrench.MATTER MADE Discus Vine 6 Pendant - Step 5 Step 6.

  6. Lift the fixture toward the ceiling. Insert the crossbar screws (I) through the crossbar slots and attach the crossbar to the junction box.MATTER MADE Discus Vine 6 Pendant - Step 6 Step 7.

  7. Using the provided wire nuts, connect the following pairs of wires from the junction box to the driver:
    – Connect the AC live wire from the junction box to the AC live wire of the driver (J)
    – Connect the AC neutral wire from the junction box to the AC live wire of the driver (J)
    – Connect the red wire (Vo+) from the fixture to the red wire (Vo+) of the driver (K)
    – Connect the black wire (Vo-) from the fixture to the black wire (Vo-) of the driver (K)
    – Connect the DIM+ wire from the junction box to the DIM+ wire of the driver (L)
    – Connect the DIM- wire from the junction box to the DIM- wire of the driver (L)
    – Connect the ground wire from the junction box to the bare copper wire attached to the crossbar (M)MATTER MADE Discus Vine 6 Pendant - Step
7 Step 8.

  8. Lift the canopy toward the ceiling and carefully tuck the wires and driver into the canopy. Using the hex key (N), loosen the slip ring set screw (O) and raise the slip ring towards the canopy.
    Retighten the set screw to secure the slip ring and canopy. Step 9.

  9. Locate the arm (P) pictured below left. Rotate the arm to the horizontal position.MATTER MADE Discus Vine 6 Pendant - Step 9Step 10.

  10. Using the hex key (Q), remove the set screw (R) from the arm. Align the hole in the arm with the hole in the internal hardware. Reinsert the set screw and tighten until the set screw is flush with the arm.MATTER MADE Discus Vine 6 Pendant - Step 10Step 11.

  11. Turn on the power and test switch and dimming function. Installation is now complete.
    Enjoy!MATTER MADE Discus Vine 6 Pendant - Step 11

MATTER MADE logo

+1 212 343 2600
mattermade.us
[email protected]

Documents / Resources

| MATTER MADE Discus Vine 6 Pendant [pdf] Installation Guide
Discus Vine 6, Pendant, Discus Vine 6 Pendant
---|---

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

MATTER MADE User Manuals

Related Manuals