EDIMAX IC-7000 Pan Tilt IP Surveillance Camera Installation Guide
- June 17, 2024
- EDIMAX
Table of Contents
Quick Installation Guide IC-7000 Pan Tilt IP Surveillance Camera
IC-7000 Pan Tilt IP Surveillance Camera
Copyright© by Edimax Technology Co, LTD. all rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or
by any means, electronic, mechanical, magnetic,optical, chemical, manual or
otherwise, without the prior written permission of this company
This company makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any
warranties, merchantability or fitness for any particular purpose. Any
software described in this manual is sold or licensed “as is”. Should the
programs prove defective following their purchase, the buyer (and not this
company, its distributor, or its dealer) assumes the entire cost of all
necessary servicing, repair, and any incidental or consequential damages
resulting from any defect in the software. Further, this company reserves the
right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or
changes.
The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about
this product, please refer to the User’s Manual on the CD-ROM.The software and
specifications subject to change without notice. Please visit our web site
www.edimax.com for the update. All right reserved
including all brand and product names mentioned in this manual are trademarks
and/or registeredtrademarks of their respective holders.
Linux Open Source Code
Certain Edimax products include software code developed by third parties,
including software code subject to the GNU General Public License (“GPL”) or
GNU Lesser General Public License (“LGPL”). Please see the GNU
(www.gnu.org) and LPGL
(www.gnu.org) Web sites to view the terms of each
license.
The GPL Code and LGPL Code used in Edimax products are distributed without any
warranty and are subject to the copyrights of their authors. For details, see
the GPL Code and LGPL Code licenses. You can download the firmware-files at
http://www.edimax.com under “Download” page.
※ The product you have purchased and the setup screen may appear slightly
different from those shown in this QIG. For more detailed information about
this product, please refer to the User’s Manual on the CD-ROM.
※ Software and specifications subject to change without notice. Please visit
our web site for the update.
※ All rights reserved. Trademarks or registered trademarks are the property of
their respective
OVERVIEW
1.1 PRODUCT DESCRIPTION
IC-7000 is an effective and easy-to-use IP Camera for remote monitoring. The
setup procedure required for this device is very simple. Built-in Web server
allows you to use web browser (e.g., Microsoft IE) through LAN or internet in
any time and any place. Type
the IP address of the IP-CAM camera on the address bar of web browser to carry
out the works of remote image monitoring and administration. Also, the user
can control the motor of the camera to change the direction of camera over
internet, and obtain the real-time image of the monitored location.
In addition, the camera supports many network protocols such as PPPoE, DHCP,
STATIC IP, DDNS, SMTP, FTP and NTP with high-performance SDRAM control and
memory card access. The built-in TV-out decoding/coding feature can display
monitored image on TV screen (NTSC or PAL TV) in families with combining fast
Motion Detection and SD Expansion Card in hardware. Moreover, IC-7000 is
equipped with IR LED, so it is capable to work in environments without light.
Besides, this device also has the function of video recording and real-time
photographing. To a family, such remote monitoring can reach professional
security and have great fun.
1.2 PACKAGE CONTENTS
- IC-7000 Pan/Tilt IP-Camera
- Power adaptor, 5V/ 1.5A .
- Ethernet Cable(red), used to connect to the network card of PC for testing purpose and camera configuration.
- Ethernet Cable (blue), used to connect to Hub, ADSL modem, residential router.
- TV-OUT A/V Cable
- Setup CD
- User’s Guide
- Accessory for mounting camera.
If any item is missing or damaged, please contact your local resellers for
service.
1.3 SYSTEM REQUIREMENT
PC
◆ Processor: Intel Pentium 4 ® 1.4GHz or above is recommended
◆ RAM: 256MB or more.
◆ Operation System: Windows 2000® or Windows XP
◆ Hard Disk: More than 10MB or more available disk spaces.
Network
◆ Network Interface: 10/100/1000 Ethernet interface..
◆ Web Browser: Microsoft Internet Explorer 6.0 or above
◆ Internet connectivity.
◆ Active-X plug-in.of IE.
1.4 INTRODUCTION OF IC-7000 EXTERIOR FUNCTIONS®
Usage of Reset Switch:
In case the system is working abnormally, press and hold Reset Switch for a
short period of time (about 3 to 5 seconds) until Status LED is illuminated.
The system will restart and the device will recover to the factory default
settings.
How to insert SD card: 1.5 PRODUCT SET-UP
UTILITIES AND TOOLS
2.1 CAM_EZ SEARCH
Insert the CD Disk into your CD-ROM drive. The Autorun.exe program should be
executed automatically. If not, run Autorun.exe manually from “Autorun” folder
in the CD. You can click the Setup Utility to configure WAN connection or
click QIG , Manual to study . If your PC do not install Adobe Reader , you
should click “Adobe Reader ” iconto install . 
When the installation is completed, you will get ”
CAM_EZ Search “ as follows ：
CAM_EZ Search is a camera search utility comes with this product. It can
search all IP CAMs connected to LAN by sending broadcasting packets. After IP
CAM responds the inquery packet, the utility will display a list of all IP CAM
found on LAN. And it allows you to modify the settings of specified IP CAM,
such as IP address or the name of IP CAM.
CAM_EZ Search Screen
2.2 USE
IP-CAM AND TEST THE FUNCTIONALITY FOR THE FIRST TIME
※ The following network architecture is suitable for IP-CAM test/ IP address
change (static IP address) /firmware update (strongly recommended).
Please refer to the following instructions:
A. Installing the camera for the first time:
- You computer must be equipped with network card and RJ-45 network connector.
- Connect the RJ-45 jack which is located at the rear of IP-CAM with the red test network cable. One end is connected to the network jack of computer; the other end is connected to the network jack located at the rear side of the IP-CAM.
- Connect the power adaptor to the power port (on the rear) of IP-CAM. Now, the status LED on the top of IP-CAM will be illuminated.
B. Make sure the IP addresses of PC and IP CAM are on the same network section:
- Usually, static IP address will be used to access Internet, so the IP address will vary. When you want to change IP address, please write down the original IP address on your computer first. Then you have to modify the IP address of your computer for testing if the IP-CAM can be operated normally or not. After finishing the test, IP address for your computer should be recovered to original settings.
- In general, the IP address for your computer in LAN will be set with “Obtain an IP address automatically”. To test the IP-CAM is working properly or not, the IP address of your computer must be changed temporarily. After the test is finished, it can be changed back to original setting.
C. Next, choose Control Panel->Network Connections->choose the activated area
Network Connections—> right click your mouse —>select Properties(P)—> Select
Internet Protocol (TCP/IP)—> Select Properties(R) , then you can check the
current IP address status for the computer. The way to modify IP address as
follows：192.168.2.5 / 255.255.255.0 / 192.168.2.254 
D. Open and execute CAM_EZ Search (as shown in Figure 2). The
system will scan the IP-CAM that you just installed automatically. Then, you
will find 255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left
mouse button. You can see the default settings of IP-CAM. 
2.3 NETWORK SETUP
Before you set up IP CAM, you have to know how your ISP provide you with IP
address (static or dynamic). If you do not know, please contact your ISP and
ask for help.
Common network architecture (1 ~ 7 types).is listed in section 2.4 of manual ,
you can refer to the listing to find out which type is suitable for your
computer and finish the setting as the instructions given in section 2.4. To
set up IP-CAM and IP address, the common way that people use is to change the
obtaining of IP address of IP-CAM. You can see the following example：
2.4 SETTING THE WAY HOW IP-CAM OBTAIN IP ADDRESS
2.4-1 STATIC – IP Address Setting**
- You computer must be equipped with network card and RJ-45 network jack.
- Connect the RJ-45 jack on the rear of IP-CAM with the red test network cable. One end is connected to the network card of computer; the other end is connected to the network jack located at the rear of the IP-CAM.
- Connect the power adaptor to the power jack (on the rear of IP-CAM). Now, the status LED on the top of IP-CAM will be illuminated.
- Open and execute CAM_EZ Search (as shown in Figure 3). The system will scan the IP-CAM that you just installed automatically. Then, you will find 255IC-7000 in the column of Camera Lists. Click 255IC-7000 with left mouse button. You can see the default settings for IP-CAM.
- Fill static IP Address as shown below. (If you do not know your IP address, please contact your ISP. An example of static IP Address modification.is shown below)
IC-7000 USER’S GUIDE
Rev. PV1.0
References
- EDIMAX - Netwoking Solution Provider including SMB Wi-Fi Access Point, AP Controller, SMB and Industrial PoE++ L2+ Switch, Industrial Embedded Wirless (Wi-Fi, Bluetooth) USB Dongle (Adapter), Wi-Fi Smart Plug, IoT, Smart Home
- The GNU Operating System and the Free Software Movement
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>