SOPHOS XGS 116 Security Appliance User Guide
- June 6, 2024
- SOPHOS
Table of Contents
SOPHOS XGS 116 Security Appliance
For more information about your appliance, scan the QR code or visit www.sophos.com/get-started-firewall
Before you begin, please confirm that you have a working Internet connection and make sure you have the account information available that was provided by your ISP.
Before Deploying
Congratulations on the purchase of your Sophos XGS appliance. This Quick Start Guide describes in short steps how to connect your appliance and explains how to open the web-based Admin Console from your administration PC. The Admin Console allows you to configure every aspect of the appliance.
What is included in the box
Appliance images: front and back XGS 116(w)
Interfaces
Mount and Connect the Appliance
Mount the antennas (for wireless models only)
Connect the provided antennas to the connectors on the back of your appliance
and align them in a vertical position.
Connect the ports to the internal and external networks
- Connect the port 1/LAN via a switch to the internal network. For this purpose, use the RJ45 Ethernet cable provided. Note that your Administration PC must also be connected to this network.
- Connect Port 2/WAN to the external network. The connection to the WAN depends on the type of Internet access.
XGS appliances are shipped with the following default settings:
Mount
the appliance to the rack
If you want to mount the device within a rack please use the optionally
available rackmount kit for this device.
Power Up the Appliance
Connect the power cable and turn on the appliance
Connect the appliance to the power supply using the power cable(s). Turn the
appliance on. The power switch is on the back of the appliance near the power
connection. During boot up the Status LED on the front will blink green. Once
the device has booted completely the Status LED will turn to solid green.
Connect Your Administration PC
Administration PC connection properties:
Use the settings below to configure your (PC/laptop) network interface:
- IP address: 172.16.16.2
- Netmask: Enter 255.255.255.0
- Default Gateway: Enter the IP address of the appliance’s internal network card (Port1/LAN): 172.16.16.16
- DNS Server: Enable this option and enter the IP address of the internal network card (Port1/LAN): 172.16.16.16
Connect your PC/laptop to Port 1/LAN of the appliance:
Start the browser and enter the IP address of the appliance’s LAN port that
your PC is connected to: https://172.16.16.16:4444
Login with the default details below:
Username: admin
Password: admin
Set Up the Appliance
Start network configuration
Select ‘Click to begin’ on the ‘Welcome’ screen to start your basic appliance
configuration. Change the interface IP addresses, default gateway, DNS
settings and date/time zone to match your local network settings.
Register the appliance
If you have not previously registered your appliance on MySophos, you will see
the registration screen “Register Your Firewall.” The appliance requires
Internet connectivity for it to be registered with MySophos. If you want to
register later, click the check box “I do not want to register now” and
proceed with section c).
If you have a serial number provided on your License Schedule please enter it into the first field and click “I have an existing serial number,” otherwise click “I don’t have a serial number (Start a Trial).”
If you are upgrading from an existing UTM/SG appliance and want to migrate your existing UTM license to your new firewall, click the respective button on the screen and browse for your UTM license to upload it to your firewall.
After clicking ‘Continue’, you will be redirected to the MySophos portal. If you already have a MySophos account, enter your login credentials under ‘Log in to MySophos’. If you are a new user, sign up for a MySophos account by entering the details under ‘Register for MySophos’.
Click ‘Continue’ to complete the registration process. Please wait while the process completes – it will take a few seconds. After successful registration, you will see a screen with the message, ‘Your device is now registered’. Please note that you should proceed with the next step, i.e. ‘Synchronize License’ only after the appliance is successfully registered.
Synchronize license
Click ‘Initiate License Synchronization’ to get the license information from
Sophos onto the appliance. After synchronization, you will see a screen with
the message, “Synchronization with server was successful.”
Connecting PoE Powered Devices
Ports 8 (on XGS 116(w) and 11/12 (on XGS 126(w)/136(w) are able to provide
power over Ethernet (PoE) to a connected PoE device which conforms to the
standards 802.3af (max. 15.4W) or 802.3at (max. 30W). Each port can provide up
to 30 watts max.
Please note: If a high performance expansion module is used in a XGS 126(w) or
XGS 136(w) module slot then the max. power of one PoE port will be limited to
15.4 watts.
Please visit www.sophos.com/en-us/support or contact your local Sophos reseller for more information about
high performance expansion modules.
Appliance LED codes
Support and Documentation
For more information and technical support, please visit www.sophos.com/en-
us/support or contact your local Sophos
reseller.
Check our Getting Started resources to find out how you can get the most out
of your purchase www.sophos.com/get-started-firewall
United Kingdom Sales Tel.: +44 (0)8447 671131 Email: sales@sophos.com
© Copyright 2021. Sophos Ltd. All rights reserved.
Registered in England and Wales No. 2096520, The Pentagon, Abingdon Science
Park, Abingdon, OX14 3YP, UK Sophos is the registered trademark of Sophos Ltd.
All other product and company names mentioned are trademarks or registered
trademarks of their respective owners.
References
- Introducción al soporte | Sophos
- Présentation du support | Sophos
- Sophos Community
- サポート概要 | Sophos
- Visão geral de suporte | Sophos
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>