Elite Screens F60NWV Portable Floor Pull Up Screen User Guide
- June 17, 2024
- ELITE SCREENS
Table of Contents
Elite Screens F60NWV Portable Floor Pull-Up Screen
Product Information
Specifications
- Product Name: Portable Floor Pull-Up Screen
- Series: Elite ez Cinema
- Models: F60NWV, F72NWV, F84NWV, F100NWV, F84NWH, F100NWH
- User’s Guide: Included
- Color: Matte White
- Website: https://manual-hub.com/
- Revision: 1.0
Precautions
Warning! Screen damage can result from product mishandling if the
enclosed precautions are not followed.
- In accordance with practicing home fire safety and to avoid screen damage, do not place the screen near or beside a fireplace or high-temperature appliances such as a gas stove, BBQ, or heater. ( Refer to Fig. 1 )
- Place the screen beyond the reach of children. ( Refer to Fig. 2 )
Product Usage Instructions
Installation
- Extend the base feet: Locate the base feet on the bottom of the box cover at each end and rotate the base foot until it forms a right angle between the footboard and the cover box.
- Open the box cover: Unlatch the buckles on both ends of the box and open the box cover. Next, secure the box with one hand while removing the support rod with your other hand.
- Installing the support rod: First, make sure that the hanging hook is pointing toward the front facing the same direction as the screen, then insert the square end of the support rod into the support plate as shown below.
- Pull up the screen: Hold the pull hook with one hand, pull the screen up gently, and hang it on the bracket hook.
- Vertical Adjustment: First loosen the locking sleeve, and then hold the small support rod with the left hand so as to slowly raise it upwards until the screen is fully stretched to the desired position.
- Adjusting the screen: Hold the screen with the left hand when the screen has been stretched to the desired position, and then rotate the locking sleeve clockwise with the right hand until the rod is properly locked into position.
Preparing screen for storage
- Pulling down the screen First, hold the telescoping support rod with the left hand and loosen the locking sleeve counterclockwise with the right hand. Then shorten the telescoping support rod slowly into the full retracted position and tighten the locking sleeve to secure it in place.
- Retract the screen: Remove the pull hook from the support bracket by lifting it about 2 cm up and then hold on to the pull hook and lower the screen gently into the box.
- Pulling out the support rod: After telescoping the small supporting rod to its shortest position and tightening the locking sleeve, take out the supporting rod from the support plate.
- Storing the support rod: Properly center the supporting rod in the middle to maintain the weight balance in the box when carrying.
- Draw the base feet back: Slightly lift each end of the box in turn rotating the two base feet underneath until they are back into alignment with the box.
- Storing the screen: The recommended place for storage would be a corner of the room or in a closet, but the ultimate choice is up to you.
FAQ
Q: How far should I place the screen from high-temperature appliances?
A: To avoid screen damage, it is recommended to not place the screen near
or beside a fireplace or high-temperature appliances such as a gas stove, BBQ,
or heater.
Q: Can children handle or reach the screen?
A: No, it is advised to place the screen beyond the reach of children.
Q: How do I adjust the screen vertically?
A: To adjust the screen vertically, loosen the locking sleeve, hold the
small support rod with your left hand, and slowly raise it upwards until the
screen is fully stretched to the desired position. Then rotate the locking
sleeve clockwise to lock the rod into position.
Q: How do I prepare the screen for storage?
A: To prepare the screen for storage, follow these steps:
- Pull down the screen by shortening the telescoping support rod and securing it with the locking sleeve.
- Remove the pull hook from the support bracket and gently lower the screen into the box.
- Telescope the small supporting rod to its shortest position, tighten the locking sleeve, and remove it from the support plate.
- Properly center the supporting rod in the middle for weight balance during storage.
- Draw back the base feet by rotating them underneath until they align with the box.
- Store the screen in a recommended place such as a corner of the room or in a closet.
Q: How should I store the support rod?
A: The support rod should be properly centered in the middle to maintain
weight balance in the box when carrying.
PARTS IDENTIFICATION
Precautions
Warning! Screen damage can result from product mishandling if the enclosed precautions are not followed.
In accordance with practicing home fire safety and to avoid screen damage, do not place the screen near or beside a fireplace or high-temperature appliances such as a gas stove, BBQ or heater. (Fig. 1)
Place the screen beyond the reach of children. (Fig.2)
Operational Instructions
Installation
The EZ-Cinema screen is designed to be used as an easy-to-operate portable
screen for a variety of presentation environments. Its design enables it to be
versatile for use in either classroom, conference room, home or patio
presentations. When packed, the unit carries with ease and opens up for
projection presentations within seconds. As a general rule, portable projector
screens should be installed in an area free from wind and heat or open flame
sources such as a heater, BBQ grill or fireworks display.
Extend the base feet
Locate the base feet on the bottom of the box cover at each end and rotate the
base foot until it forms a right angle between the footboard and the cover
box.
Open the box cover
Unlatch the buckles on both ends of the box and open the box cover. Next,
secure the box with one hand while removing the support rod with your other
hand.
Installing the support rod
First, make sure that the hanging hook is pointing toward the front facing the
same direction as the screen, then insert the square end of the support rod
into the support plate as shown below.
Pull up the screen
Hold the pull hook with one hand, pull the screen up gently and hang it on the
bracket hook.
Vertical Adjustment
First loosen the locking sleeve, and then hold the small support rod with the
left hand so as to slowly raise it upwards until the screen is fully stretched
to the desired position.
Adjusting the screen
Hold the screen with the left hand when the screen has been stretched to the
desired position, and then rotate the locking sleeve clockwise with the right
hand until the rod is properly locked into position.
Screen completely assembled
Preparing screen for storage
Pulling down the screen
First, hold the telescoping support rod with the left hand and loosen the
locking sleeve counter-clockwise with the right hand. Then shorten the
telescoping support rod slowly into the full retracted position and tighten
the locking sleeve to secure it in place.
Retract the screen
Remove the pull hook from the support bracket by lifting it about 2 cm up and
then hold on to the pull hook and lower the screen gently into the box.
Pulling out the support rod
After telescoping the small supporting rod to its shortest position and
tightening the locking sleeve, take out the supporting rod from the support
plate.
Storing the support rod
Properly center the supporting rod in the middle to maintain the weight
balance in the box when carrying.
Draw the base feet back
Slightly lift each end of the box in turn rotating the two base feet
underneath until they are back into alignment with the box.
Storing the screen
The recommended place for storage would be a corner of the room or in a
closet, but the ultimate choice is up to you.
The following points should be noted to assure the sound performance of the screen
- Never use your hand to touch the screen surface.
- Never scrabble on the screen with anything.
- Don’t touch the screen with hard or sharp objects.
- Please use a clean cotton cloth or soft dust brush to remove any dust particles on the screen.
- The screen material may be cleaned
Warranty Policy – Manual, Tripod, Pull-up Floor, and Fixed Frame Screens
*Warranty policy applies to claims made in the United States of America. Warranty issues outside of the US must go through their international distributor.
- Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified below):
- Refurbished units carry a 90-day parts and labor warranty.
- Demo units or open box items are AS IS items and do not carry a warranty.
- Elite Screens will cover ground shipping charges on warranty claims made within 7 days of receiving per our DOA (Defective On Arrival) policy
- Each party will be responsible for one way shipping during the regular warranty period if the claim is made after the 7 day DOA period.
- An RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite Screens will either replace or repair the defective unit with a brand new replacement (see exceptions below) after the defective unit is received and/or confirmed defective. Once the product is received, Elite Screens will send out a new unit to the customer by ground service (subject to inventory availability).
- Missing Parts must be reported within the 7-days of receipt. If reported after 7 days, customer will only be responsible for shipping and handling fees. If reported after 30 days of receipt, the customer is responsible for cost of the parts and shipping & handling fees.
Please visit the link below for full warranty information
http://www.elitescreens.com/services.html
*A new or refurbished replacement will be sent out to the customer depending on the type of purchase (new or refurbished) and is based on stock availability.
TWO WAYS TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC.
- A. On Line (Faster and Easier) www.elitescreens.com/register.html
- B. Fill out & Fax to 562-483-8498, Attn: Customer Service Dept.
If you have pictures of your screen you’d like to share with us, please email your pictures to eliteinfo@elitescreens.com or call us at 877-511-1211 www.elitescreens.com For any technical inquiries, techsupport@elitescreens.com
Precautions
- Warning! Screen damage can result from operational errors if the enclosed precautions are not followed.
- In accordance with practicing home fire safety and avoiding screen damage, do not place the screen near or beside a fireplace or high-temperature objects such as a gas stove, BBQ or heater.
- Place the screen beyond the reach of children.
*Note: The Flex Bar is a feature designed to evenly distribute the tension of the screen out to the sides. The Flex Bar is designed to “bow” out from the Top Support Bar. It may bow out a few inches depending on the size of the screen. (Fig.3)
Operational Instructions
Installation
The screen should be installed in an area free of very strong wind and away from any fire activity such as a heater, BBQ grill or fireworks display.
-
Extend base feet
Locate the base feet on the bottom of the box at each end and rotate them until they form right angles.
-
Open the box cover
Unlatch the buckles at both ends of the box and open the box cover.
-
Pulling up the screen
Carefully lift the screen by its handle and stop at the desired height position. The screen’s “scissor back” spring configuration will support it .
Note : The screen will only stop shortly after the bottom black rise has been exposed.
Putting screen away
-
Retract the screen into case
Press the screen’s handle slowly in a downward motion and allow the screen to retract back gently into the housing.
-
Closing it up
Snap the buckles into place at both ends and verify that the screen’s box is closed securely.
-
Draw the base feet back
Slightly lift one end of the box at a time and rotate the two feet on the bottom of the box until they are in parallel alignment with the box.
-
Storing the screen
The recommended place for storage would be a corner spot or in a closet, but the ultimate choice is up to you.
The following points should be noted to assure the sound performance of the screen.
- Never use your hand to touch the screen surface.
- Never scrabble on the screen.
- Don’t touch the screen with hard or sharp objects.
- Please use clean cotton cloth or soft dust brush to remove dust particles from the screen.
Warranty Policy – Manual, Tripod, Pull-up Floor, and Fixed Frame Screens
- Two (2) year warranty parts and labor from purchase date as follows (except for refurbished units as specified below):
- Refurbished units carry a 90-day parts and labor warranty.
- Demo units or open box items are AS IS items and do not carry a warranty.
- Each party will be responsible for one way shipping during the warranty period.
- DOA (Defective On Arrival): Must be reported within 7 business days of receipt. A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement. Elite Screens will replace the DOA (Defective On Arrival) unit with a brand new replacement (see exceptions below) after the DOA unit is received and/or confirmed defective. Once the product is received, Elite Screens will send out a new unit to the customer by ground service (subject to inventory availability). Should a problem be reported after the 7-day grace period, the item must be shipped to us for warranty repair.
- Missing Parts must be reported within the 7-day (DOA) grace period. If reported after 7 days, customer will be only be responsible for shipping and handling fees. If reported after 30 days of receipt, customer is responsible for cost of the parts and shipping & handling fees.
TWO WAY TO REGISTER YOUR WARRANTY WITH ELITE SCREENS INC.
- On Line (Faster and Easier) www.elitescreens.com/register.html
- Fill out & Fax to 562-483-8498, Attn: Customer Service Dept.
If you have pictures of your screen you’d like to share with us, please email your pictures to eliteinfo@elitescreens.com or call us at 877-511-1211 www.elitescreens.com For any technical inquiries, techsupport@elitescreens.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>